Parts for Ge HST22IFMCCC: 02 - Sealed System & Mother Board Parts

Replace your refrigerator water filter every 6 months to maintain clean water and ice. Removes contaminants for fresh taste. Easy DIY install in minutes.

Replaces lost or stripped 8-36 threaded mounting screws in dishwashers, ice makers, and refrigerators. Secures panels, brackets, and components.

Secures the drain tube to prevent water pooling or dripping. Replace if the clip is cracked, broken, or the tube has come loose. Verify fit with your model.

Replacement rear wheel for refrigerators. Mounts to the bottom rear frame to enable smooth rolling for cleaning and repositioning. Order if cracked or missing.

Replaces a cracked, severed, or frozen ice maker fill tube and grommet. Delivers water from valve to ice maker. Includes tube, grommet, and plate.

Water line fitting that connects the ice maker supply tube. Replace if cracked, leaking, or damaged to restore a secure seal and prevent water leaks.

Replaces a cracked, severed, or frozen ice maker fill tube and grommet. Delivers water from valve to ice maker. Includes tube, grommet, and plate.

The Lid Bumper is an OEM part for GE refrigerators. It is designed to provide cushioning and protection for the refrigerator lid, preventing damage and ensuring smooth, quiet closing. 

Causes of a bad Lid Bumper can include deterioration over time due to frequent use, exposure to temperature variations, or damage from accidental impacts. A worn or damaged bumper may no longer provide adequate cushioning, leading to potential damage to the lid or the refrigerator itself.

Symptoms of a bad Lid Bumper include:

• The refrigerator lid closing too hard
• Unusual noises when closing the lid
• Visible wear or cracks on the bumper

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

This access cover protects internal components and wiring behind the appliance cabinet, keeping parts secure and helping maintain proper airflow. It replaces a cracked, missing, or damaged cover to restore safe, finished appearance. What it does

• Covers and protects control boards, wiring, or service areas inside the cabinet
• Prevents debris entry and reduces risk of accidental contact with electrical components
• Stops rattling or vibration caused by a loose or broken cover
• Helps restore the appliance's finished look after damage or repair

• One access cover

• Disconnect power before starting any work to avoid shock hazard
• Typically secured with screws or clips; retain hardware for reinstallation or replace if damaged
• Handle gently to avoid cracking; align tabs and fasteners before tightening

Rubber grommet that mounts the evaporator or condenser fan motor to its bracket. Replace when worn, cracked, or missing to reduce vibration and noise.

Supplies electrical power from wall outlet to refrigerator. Replace this cord if cut, frayed, overheated, or damaged to restore safe electrical connection.

Guides airflow across the condenser and secures the fan motor in place. Replace if cracked, broken, or missing to restore proper cooling airflow.

Guides airflow across the condenser and secures the fan motor in place. Replace if cracked, broken, or missing to restore proper cooling airflow.

Sealer plug for refrigerators. Seals unused holes or openings in cabinet panels. Replace if cracked, broken, or missing to maintain proper appearance.

Fix a refrigerator that's not cooling or has an overheated compressor. This condenser fan motor circulates air over the compressor and coils. DIY-friendly.

Refrigerator running hot or making loud noises? A worn condenser fan blade prevents proper airflow across coils. DIY repair in 30 minutes or less.

Secures and seals water line connections in your refrigerator's dispensing system. Replace if leaking or loose to prevent water damage. Confirm fit.

Size: 8-32 t. Includes 12 screws.

Rear condenser fan mounting bracket for refrigerators and freezers. Replaces broken, cracked, or missing brackets that secure the fan assembly.

Fix a refrigerator that won't start or clicks repeatedly. This compressor capacitor stores energy to start the motor. DIY repair typically takes 30 minutes.

Refrigerator not cooling or running constantly? A damaged condenser coil prevents proper heat release. This assembly restores cooling efficiency.

Refrigerator won't cool and compressor won't run? A faulty start relay prevents the compressor from starting. Moderate DIY repair, 30-45 minutes.

This is a grommet and it is intended for use on refrigerators and freezers. This is a genuine replacement part made by General Electric. A new grommet might be needed if the current one is visibly worn out or damaged in any way. If there are noises from vibration coming from the lower back area of the fridge there might be need for a new grommet. This is an OEM part sourced directly from the manufacturer, and it is sold individually. It is compatible with refrigerators and freezers, or units with a compressor and is made by General Electric.

The R134 Drier is an OEM part for GE refrigerators. This component plays a critical role in the refrigeration system by removing moisture and contaminants from the refrigerant, ensuring efficient cooling and preventing damage to other parts of the system. It helps maintain the purity and effectiveness of the refrigerant as it cycles through the system.

You should replace the R134 drier if it becomes clogged or damaged. Common causes of a bad drier include wear and tear over time, exposure to moisture, or contamination from other failing components in the refrigeration system.

Symptoms of a bad R134 drier include:

• Reduced cooling efficiency
• Frost buildup on the evaporator coils
• Unusual noises from the refrigeration system
• Increased energy consumption
• Refrigerator not maintaining the set temperature

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Replacement shelf support stud for refrigerator shelves. Installs to hold shelves in place. Needed when original stud is broken, cracked, or missing.

Condenser air baffle for refrigerators. Directs airflow over the condenser coils. Replace if cracked, broken, or missing to maintain proper air circulation.

Replacement mounting screw for securing panels, trim, and internal components in appliances. Needed when original screws are stripped, lost, or damaged.

Secures the condenser fan motor in position. Replace this bracket if cracked, bent, or causing excessive vibration to restore stable mounting.

10-32 x 5/16 machine-thread screw secures refrigerator panels, trim, and internal brackets. Replaces missing or damaged fasteners to prevent rattles.

This self-adhesive foam strip provides a flexible seal and buffer for appliance gaps, helping reduce drafts, rattling, and moisture intrusion. Designed for easy stick-on replacement where foam padding or sealing is needed. What it does

• Seals small gaps between components to help reduce air leaks and temperature loss
• Cushions panels and doors to minimize noise and vibration
• Helps block moisture and dust from entering sensitive areas
• Self-adhesive backing allows for quick placement without extra glue

• One self-adhesive foam strip

• Surface must be clean and dry; wipe with isopropyl alcohol for best adhesion
• Measure and trim the foam strip to fit—use scissors or a utility knife
• Press firmly along the length to ensure full contact; allow adhesive to set before closing doors or panels
• For safety, disconnect power to the appliance before working in internal areas

Secures the condenser unit in your refrigerator. Replace if loose, broken, or causing vibration noise. Verify fit with your model number before ordering.

Plastic cover that conceals and protects water supply tubing behind the lower kickplate. Replace if cracked, broken, or missing for a finished look.

Secures water tubing to fittings in refrigerators and dishwashers. Replace if leaking, tubing slips off, or clamp is cracked. Confirm fit with model number.

Water dispenser won't shut off or no water flowing? This inlet valve controls water to your ice maker and dispenser. DIY repair in 10-15 minutes.

Fix a refrigerator that won't cool or has temperature control issues with this main control board. Moderately difficult repair, taking 15-45 minutes.

Secures refrigerator wiring to prevent chafing and vibration noise. Replace when damaged or missing to keep harnesses organized. Confirm fit by model.

Plastic water line that runs from the water valve to the icemaker fill tube. Replace if cracked, brittle, broken, or leaking at connection points.

Foam insulator that protects the main control board in your refrigerator. Replace if cracked, compressed, or missing to prevent moisture damage.