Parts for Electrolux ELTE760CAT0: 02 - Upper Cabinet / Drum Heater Parts

This is a left-side access panel in a titanium finish that forms part of the dryer's outer cabinet. It provides structural support and protects the internal components from dust and debris. Replace this panel if it is dented, cracked, rusted, or if the finish is damaged.

Secures the front panel to your washer frame. Replace this clip if your panel is loose, rattling, or won't stay in place due to a broken or missing clip.

If your dryer runs too hot, won't heat properly, or shuts off unexpectedly, the inlet thermistor may have failed. This sensor monitors incoming air temperature.

Replace your dryer's exhaust duct assembly if cracked, damaged, or missing. Routes air from the dryer to the vent outlet for safe, efficient operation.

If your dryer drum won't turn or makes grinding noises, a worn drive shaft may be the cause. This metal shaft transfers motor torque to rotate the drum.

Replacement drum support roller wheel assembly for dryers. Installs on bulkhead to support and guide drum rotation. Replace when worn, cracked, or loose.

Positioning spacer that maintains proper gaps between dryer components. Replace if cracked, broken, or missing to prevent parts from rubbing together.

Metal mounting nut secures panels, brackets, and assemblies on your dryer. Replace if cracked, stripped, missing, or causing loose components.

Rubber grommet cushions wiring, tubes, or panels in your dryer. Replace if cracked, worn, or missing to prevent chafing and reduce vibration noise.

This replacement nozzle assembly directs and controls water flow in the appliance, restoring proper delivery to the dispenser or ice-making components. It replaces a worn or damaged nozzle to help stop leaks and restore consistent flow. What it does

• Directs water from the supply line to the dispenser or ice-making fill tube.
• Helps stop spraying or leaking when the original nozzle is cracked or blocked.
• Restores steady water flow when the dispenser produces weak or intermittent water.
• Fits into the original mounting and seals the water path when properly installed.

• One nozzle assembly as shown.

• Turn off water supply and unplug the appliance before starting work.
• Inspect surrounding seals and tubing; replace any damaged parts to ensure a proper seal.
• Hand-tighten fittings and check for leaks after restoring power and water.

Fixes steam cycle not working or water not entering drum during steam cycles. Controls water flow into dryer. Moderate DIY repair for steam dryers.

Secures internal components in your dryer. Replace this mounting bracket if cracked, broken, or missing to restore proper alignment and stability.

Replacement drum for your dryer. Installs in the dryer cabinet to hold and tumble clothes during cycles. Order a new drum if yours is cracked or damaged.

Replace your dryer seal to prevent air leaks, heat loss, and moisture escape. Restores tight barrier for efficient drying. Check fit with your model.

This straight drum baffle creates tumbling action inside your dryer drum to lift and separate clothes for even drying. It extends from the drum wall to catch and lift garments as the drum rotates. Replace this baffle if clothes aren't drying evenly, take longer to dry, or if the original baffle is cracked or missing.

Gray molded paddle that lifts and tumbles clothes inside the dryer drum. Replace if cracked, broken, warped, or pulled loose from the drum wall.

Transfers motor power to rotate the drum. Replace if dryer hums but won't spin or makes squealing sounds. Verify fit with your model number.

Fix poor drying or overheating caused by restricted airflow. This air duct assembly routes hot air through your dryer to restore proper circulation.

Traps lint before it enters the exhaust system. Replace if damaged, torn, or causing lint buildup. Confirm fit with your dryer's model number.

Replace your dryer door gasket to restore an airtight seal and improve drying efficiency. Install when gasket is torn, cracked, or allows air leaks. Confirm fit with your model number before ordering.

This is a door switch that detects whether the dryer door is open or closed. When the door is shut, the switch completes the circuit and allows the dryer to run. Replace this switch if the dryer does not start when the door is closed, stops mid-cycle unexpectedly, or the drum light does not turn on or off properly when the door is opened and closed.

Dryer not starting or shutting off mid-cycle? A faulty wire harness disrupts electrical signals to motors, heating elements, and controls. Moderate DIY repair.

Dryer door won't stay closed or latch properly? This door latch assembly secures your dryer door during operation. Simple DIY fix with just two screws.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Dryer frame assembly that forms the structural housing for your dryer. Replace if cracked, warped, or damaged to restore cabinet integrity and support.

Replacement door glass for dryer doors. Provides a clear viewing window to monitor laundry during cycles. Order when glass is cracked, broken, or missing.

Secures dryer vent hose connections to prevent air leaks and maintain proper airflow. Replace if rusted, cracked, or loose. Confirm fit with your model.

This is a metal or plastic bracket that serves as a protective cover over the terminal block where the power cord connects to the dryer. It shields the electrical connections from accidental contact and helps prevent short circuits. Replace this part if it is cracked, missing, or damaged - an exposed terminal block is a safety hazard.

Rubber cushion bumper for dryers. Installs between panels or assemblies to reduce vibration and noise. Replace if cracked, worn, or missing.

This metal top panel replaces the upper rear control housing on compatible Frigidaire ranges and stoves, restoring a secure mounting surface for controls and improving cabinet fit and appearance. Ideal for repairing bent, rusted, or damaged panels. What it does

• Replaces the upper rear housing that supports control knobs, switches and the backguard area
• Restores proper alignment and spacing between the cooktop and rear controls
• Stops light leaks and relieves stress from warped or bent panels
• Commonly used when the panel is dented, rusted, cracked, or has broken mounting tabs

• One top panel

• Disconnect power (and gas, if applicable) before starting any work
• Handle sharp sheet-metal edges with gloves; panel edges can be sharp
• Remove control knobs, backguard, or trim as required and save screws for reinstallation
• Align mounting tabs and secure with original hardware; test controls after reassembly

Plastic cap cover for dryer installation. Replaces cracked, broken, or missing covers. Snaps into place to provide clean finished appearance.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Replacement 1/4-14 x 3/8 threaded screw for securing dryer panels, trim, and brackets. Restores proper fit when original screws are stripped or missing.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Mounting screw secures panels, brackets, and internal components in your dryer. Replace if missing, stripped, or damaged during repairs or maintenance.

Replacement mounting screw for dryers. Secures panels and internal components. Needed when original screw is stripped, damaged, missing, or causing loose parts.

Hex washer head ,10-32 x 0.375. Ground

Phillips pan head screw for securing panels and components in appliances. Replace missing, stripped, or corroded screws during repairs or maintenance.

Replacement mounting screw that secures panels, brackets or small components in compatible appliances. Installs quickly to replace stripped or missing fasteners and help stop rattling and restore proper alignment. What it does:

• Fastens panels, trim pieces, brackets and other small assemblies to the appliance.
• Replaces stripped, corroded or broken screws that can cause loose parts or vibration noise.
• Helps restore proper alignment of doors, drawers or trim when a missing screw allows movement.
• Small appliance fastener sized for original mounting points—use the OEM screw whenever possible.

• Disconnect power and water before starting any repair.
• Start the screw by hand to avoid cross-threading; use the correct screwdriver or bit.
• Tighten snugly but avoid overtightening to prevent stripped threads or damaged plastic.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic