Parts for Whirlpool WRT148FZDB07: 06 - Unit Parts

This heater is the internal heating element that produces heat for the appliance, restoring normal operating temperature and performance. Replacing a failed heater brings the unit back to expected heating capability. What it does:

• Converts electrical power into heat to warm the appliance during normal cycles
• Restores proper temperature when the unit is no longer reaching or maintaining heat
• Helps eliminate symptoms such as little or no heat, extended cycle times, or inconsistent temperatures
• Works with the appliance's controls and safety sensors to deliver controlled heating

• One heater

• Disconnect power (and gas supply if applicable) before starting work to avoid electric shock or fire
• Handle element carefully to avoid bending or damage; avoid contact with sharp edges

Screw: 8-16 x 3/8 inch.

This bale strap is a direct-replacement part that helps secure the dryer's latch/bale assembly so the door closes and stays closed during operation. Replacing a worn or broken strap restores reliable door engagement and safer drying cycles. What it does:

• Anchors the dryer door's latch/bale so the door remains properly closed during operation
• Prevents intermittent door opening that can stop cycles or cause heat loss
• Replaces a stretched, torn, or broken strap that no longer holds the latch securely
• Works with the door/latch mechanism to maintain safe operation during drying

• One bale strap

• Disconnect power before beginning any repair to avoid electrical shock
• Verify strap routing and attachment points match the original before reinstalling
• Basic hand tools are typically required; avoid forcing plastic clips to prevent breakage

This heat probe is a temperature sensing component used in the refrigeration system to monitor heat levels near the evaporator or compressor area. It helps the control board regulate cooling cycles for proper temperature management. Replace this part if the refrigerator is not cooling correctly, runs continuously, or displays temperature error codes.

Replacement fastener screw for appliances. Secures panels, trim, clips, and components. Needed when original screws are stripped, missing, or damaged.

Control panel buttons not responding? This wire harness connects your touch interface to the main control board, restoring reliable button response.

Fix uneven cooling or warm spots in your refrigerator with this air baffle. Directs airflow between compartments to restore temperature balance. Easy DIY fix.

Protective seal grommet for hoses, tubes, or wires passing through refrigerator cabinet. Replaces cracked, worn, or missing grommets to prevent leaks.

The compressor start device provides the initial electrical boost needed to start the refrigerator's compressor motor. Located near the compressor at the back of the refrigerator, replace it when the compressor won't start, runs intermittently, or the refrigerator isn't cooling properly.

Secures panels, hoses, and wiring in place to prevent rattling and loose components. Replace when worn or broken to restore proper fit. Confirm compatibility with your model number.

This refrigerator roller supports the unit's weight and enables smooth movement for positioning and cleaning. Replace when wheels crack or roll roughly.

Cabinet roller axle supports refrigerator wheels for smooth movement. Replace if rollers wobble or fridge is hard to move. Verify fit with your model.

The Run Capacitor is an OEM part for Whirlpool appliances, designed to provide the necessary electrical charge to start and run the compressor motor. This part attaches to the compressor to aids in maintaining a consistent motor speed and ensuring smooth operation. The run capacitor plays a crucial role in the appliance's electrical system, storing and releasing energy as needed to power the motor.

Causes of a bad Run Capacitor include electrical surges, wear and tear over time, or overheating, which can lead to a failure in providing the necessary start-up energy or maintaining motor speed.

Symptoms of a bad Run Capacitor include:

• The appliance does not start.
• The motor shuts off shortly after starting.
• The appliance is humming but not running.
• Increased energy consumption.

This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

Replacement clip for your refrigerator. This small fastening component secures interior parts in place. Order a new one if yours is broken or missing.

Replaces stripped, missing, or damaged mounting screws that secure panels, brackets, and components in your refrigerator. Restores proper assembly.

Fix a refrigerator that's not cooling properly with this condenser fan motor. Replaces worn motors causing poor heat exchange. Video guide included.

Filters and dries refrigerant in your refrigerator's cooling system. Replace if you notice cooling issues, leaks, or clogs. Verify fit with your model.

Seals openings where hoses or wires pass through cabinet walls. Replace if cracked, torn, or missing to prevent chafing and vibration noise. Verify fit.

Size: 8-18 x 1/2 inch.

This is the fan blade that attaches to the condenser fan motor, typically located near the bottom rear of the refrigerator. It draws air across the condenser coils to dissipate heat and keep the refrigerator running efficiently. Replace this blade if it is cracked, warped, or broken, which can cause loud noises, reduced cooling performance, or the compressor overheating.

This insul-sound deadening pad reduces vibration and noise by dampening panels and components in laundry and kitchen appliances. It's a small adhesive-backed sound/isolation pad used where noise or rattles transfer through metal surfaces. What it does

• Dampens rattles and reduces structure-borne noise from panels, cabinets and housings.
• Helps isolate vibrating components from appliance chassis to lower perceived sound.
• Commonly applied behind control panels, cabinet walls or on motor mounts to cut vibration transmission.
• Useful when worn, detached or hardened factory pads allow increased noise.

• One insul-sound deadening pad

• Disconnect power before servicing an appliance to avoid shock or injury.
• Clean and dry mounting surface; press pad firmly to ensure adhesive contact.
• Replace only in the original location; do not cover vents or moving parts.
• If adhesive is weak, use OEM-approved adhesive; avoid solvents that may damage finishes.

Drain tube that routes defrost water from the evaporator to the drain pan. Replace if cracked, clogged, or disconnected to prevent water leaks.