Parts for Maytag LAT9400AAE: 08 - Tub-Inner & Outer (Lat9400aae & 9400Abe) Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Supports the inner tub for smooth spinning during wash cycles. Replace when you hear grinding noise or see water leaking from bottom center of tub.

Supports the inner tub for smooth spinning during wash cycles. Replace when you hear grinding noise or see water leaking from bottom center of tub.

The Mounting Stem Repair Kit is an OEM part for Whirlpool washing machines. It includes all necessary components to repair the mounting stem, which is a critical part of the washer's tub support system. Comes with the hub assembly, seal, and spanner nut. 6-2040130 should also be replaced at the same time. A spanner wrench is required to complete the repair TB123B.

Symptoms of a bad mounting stem include:

• Excessive noise or vibration during the spin cycle.
• The washer tub appearing loose or off-balance.
• Leakage around the central area of the washer, indicating a possible seal failure.

Causes of a bad mounting stem can include wear and tear from normal usage, especially with heavy loads, or corrosion and material fatigue that weaken the stem's integrity.

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This small clamping nut secures a mating clamp or bracket so the connected component stays firmly in place. Replacing a worn, stripped, or missing nut restores a solid hold and helps prevent looseness or leaks around the secured area.

• Secures a clamp or bracket to its mounting point
• Restores proper clamping force when the original nut is stripped or missing
• Common signs: loose clamp, rattling/vibration, clamp won't tighten, minor leaks where the clamp is used
• Durable hardware replacement to maintain stable, reliable assemblies

• Disconnect power and shut off water/gas to the appliance before service
• Note clamp/bracket orientation before removal for correct reassembly
• Start threads by hand to prevent cross-threading; then tighten with the appropriate tool
• Do not overtighten—snug just enough to securely clamp the component

Seals the agitator shaft opening to prevent leaks and protect internal components. Replace if you see water leaking from the center post during wash cycles.

Fix agitator wobble and excessive vibration with this retaining washer. Secures center-mounted components to prevent looseness and noise during operation.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Leaking during fill or rinse? This bleach dispenser hose carries bleach from the dispenser to the tub. Quick 15-minute fix stops leaks and restores flow.

This hose clamp secures a rubber or plastic hose to its fitting to maintain a tight, leak-resistant seal. Replace a worn or missing clamp to stop drips and keep appliance water connections secure.

• Fastens a hose to a barb or port to prevent leaks
• Helps keep hoses from slipping off due to vibration or pressure
• Restores proper sealing when a clamp is rusted, bent, or stripped
• Common symptoms: water dripping at a hose joint, loose hose connection, or a clamp that won't tighten

• Disconnect power and shut off the water supply before servicing
• Place a towel to catch residual water when removing hoses
• Position the clamp just behind the hose barb/bead and secure with the appropriate tool
• Restore water and power, then run a quick check for leaks at the connection

Hose clamp for securing water supply and drain hoses on the washer. Provides leak-free seal at hose connection points.

Connects the washer tub to the drain pump for water drainage. Replace if cracked, leaking, or split. Installs between the tub outlet and pump inlet.

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to maintain a secure seal
• Helps stop drips, seepage, or loose connections
• Common fix when you see moisture around a hose joint
• Useful if a clamp is rusted, stretched, or no longer holding tension

• Unplug power and shut off water (if applicable) before servicing
• Note clamp position/orientation before removal
• Use appropriate screwdriver or nut driver to tighten evenly
• Do not overtighten—ensure a snug, leak-free seal without damaging the hose

The Hose Clamp is an OEM part for Whirlpool washing machines. This clamp secures the hose in place, ensuring a tight connection and preventing leaks during operation. It is essential for maintaining the integrity of the washing machine's water system, securing hoses that carry water to and from the washer.

Common causes of a bad hose clamp include rust, physical damage, or loosening from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Water leaks around the hose connection points
• The hose slipping off the fitting
• Visible rust or wear on the clamp
• Difficulty in tightening the clamp to secure the hose

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.

Mounting bolt secures the tub and internal components in your laundry center. Replace if stripped, rusted, or missing to restore stable assembly fit.

Replacement mounting bolt for washer outer tub assembly. Secures tub components together with nut. Replace if rusted, stripped, loose, or missing.

Washer overflowing or not filling properly? A clogged or cracked pressure switch hose prevents proper water level detection. Simple 15-minute DIY fix.

The Hose Clamp is an OEM part for Whirlpool appliances. It secures hoses in place, ensuring a tight connection and preventing leaks in various systems such as washing machines, dishwashers, and refrigerators. This clamp is crucial for maintaining the integrity of the water or air lines it secures.

Causes of a bad hose clamp include wear and tear over time, exposure to water and detergents, or mechanical stress from repeated tightening and loosening.

Symptoms of a bad hose clamp include:

• Leaks at the hose connection points
• Hoses slipping off the connections
• Visible rust or damage on the clamp
• Reduced appliance efficiency due to leaks

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.