Parts for Maytag DE8420: 10 - Thermostats Parts

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The Thermal Fuse is an OEM replacement part for Whirlpool dryers. This safety device monitors and protects heating elements inside the dryer. If temperatures rise too high due to a blockage or other issue, the fuse automatically opens the electrical circuit to cease further heating. 

Symptoms of a bad thermal fuse include:

• Dryer failing to heat or stay warm during cycles
• Fluctuating or inconsistent heat levels  
• Tripped circuit breakers after drying

Causes of failure involve wear or damage from years of high heat exposure. Over time, components become brittle and less responsive.

This OEM Whirlpool replacement is also compatible with some Kenmore, Admiral, Roper, and Estate dryer models. 

This multi-temperature cycling thermostat regulates the dryer's drum heat, switching the heater on and off to match the temperature setting you choose. It can help restore consistent drying if temperatures are erratic, loads run too hot, or cycles take too long.

• Maintains target temperature by opening and closing the heater circuit across multiple heat settings
• Provides calibrated temperature control for safe, efficient drying
• Failure may present as no heat or low heat, overheating, very long dry times, or inconsistent temperatures
• Intended for models with multiple temperature selections

• Unplug the dryer; shut off gas supply if applicable. Allow the appliance to cool before servicing.
• Take a photo of wire positions; move wires to the new thermostat one at a time to matching terminals and ensure snug connections.
• Remove/install mounting screws and seat the thermostat flat against the mating surface for proper sensing.
• After reassembly, clear lint passages and verify proper vent airflow.

• If there's no heat at all, also check the thermal fuse, high-limit thermostat, heating element (electric), or igniter/burner components (gas).
• Restricted venting can mimic thermostat issues and cause overheating or long dry times.

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts of the appliance stay in place. It is commonly used in different locations within the appliance, such as the cabinet, panels, or other structural elements.

This part fixes the following symptoms:

• Loose or wobbly components within the appliance
• Panels or parts that are not securely attached
• Rattling or unusual noises due to loose parts
• Damaged or missing screw

The Whirlpool screw can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

A single mounting screw designed to secure panels, brackets, or components on your appliance for reliable fit and reduced vibration. Use this genuine replacement when a fastener is missing, stripped, or rusted. What it does:

• Fastens panels, trim, or mounting brackets to restore proper alignment
• Helps eliminate rattling or vibration caused by loose or missing screws
• Replaces corroded or damaged hardware to maintain safe operation
• Restores secure attachment for parts that no longer hold in place

• Disconnect power to the appliance before starting any repair
• Use the correct driver bit to avoid stripping the screw head
• Tighten until snug; avoid overtightening which can strip threads or damage parts