Admiral Dishwasher Parts

Replace the cable bracket guide roller on your dishwasher. This small wheel guides the door cable smoothly through the bracket, preventing binding and wear.

Replacement tension spring for dishwasher doors and mechanisms. Restores proper return force when the original spring is broken, stretched, or missing.

This drain hose routes and removes wastewater from the appliance so it can pump out normally and avoid standing water. It's a direct-fit service part used to restore proper draining. What it does

• Carries wastewater from the appliance pump to the household drain or air gap
• Restores normal draining when original hose is cracked, split, or leaking
• Helps prevent water backing up into the appliance when properly routed and secured
• Can stop intermittent leaks or reduced drain performance caused by hose damage

• One drain hose

• Disconnect power and turn off water supply before starting any repair
• Inspect hose routing and replace with the same path to avoid kinks or high loops that trap water
• Secure hose connections with appropriate clamps; tighten but avoid over-torquing
• After installation, run a short drain cycle and check all connections for leaks

Adjustable leveling feet that restore stability and balance to your appliance by letting you fine-tune height at each corner for a flat, wobble-free install—helps reduce vibration and improve door fit and operation. What it does:

• Provides adjustable height to level an appliance on uneven floors.
• Eliminates rocking or wobbling that can cause vibration, noise or movement during operation.
• Helps ensure doors and panels sit flush and seal properly.
• Durable replacement designed for direct fit where the OEM leveling foot is specified.

• Disconnect power and water before performing any work.
• Support the appliance so it cannot tip—use a jack or have a helper hold it while you adjust feet.
• Turn the foot to raise or lower the corner; use hand tools as needed and avoid excessive force.
• After adjusting, check stability and run a short cycle to ensure vibration and alignment are resolved.

Hose assembly for portable dishwashers. Connects your unit to the sink faucet for water supply. Replace if cracked, leaking, or stripped threads.

Kit contains two 10 feet inlet hoses.

Replacement mounting screw for securing panels, brackets, and internal components. Needed when original screws are stripped, missing, or damaged during repair.

Fix loose or rattling dishwasher trim panels with this dispenser retainer clip. Secures interior panels and exterior trim for proper fit. Easy repair.

This replacement cap protects a small appliance service or service-valve area from dirt, moisture and accidental contact to help maintain proper operation. Simple, durable cover that restores the original sealed fit for affected components. What it does

• Covers and protects vulnerable valve/service openings or terminals from debris and moisture.
• Helps prevent contamination that can cause poor connections or service issues.
• Keeps small components secure and reduces risk of accidental contact or damage.
• Useful when the original cap is cracked, lost or no longer provides a tight seal.

• One replacement protective cap.

• Disconnect power or follow appliance-specific safety procedures before inspecting or servicing.
• Press the cap into place until it seats snugly; do not force if it resists.

Fix detergent not dispensing or dispenser door not opening with this dishwasher dispenser shaft kit. Repairs broken or worn dispenser mechanisms.

Replace your dishwasher's spring adjustment bracket if cracked, bent, or missing. This structural component secures the spring mechanism inside your unit.

Note: For faucet adapter

O-ring seal for dishwasher turbidity sensor. Replace if you notice leaking around the sensor or water pooling inside the dishwasher. Confirm fit with model.

A replacement appliance door handle that restores a secure grip and proper operation to a worn or broken handle. Designed to match the original mounting style for a clean, factory-fit appearance. What it does:

• Provides a sturdy grip for opening and closing the appliance door smoothly
• Replaces cracked, loose, or broken handles that affect normal door use
• Restores correct alignment and leverage to reduce strain on door components
• Helps prevent accidental drops or slippage when grabbing the door

• One replacement handle

• Remove power and empty the door area before starting any repair
• Typical install requires removing trim or screws; use manufacturer-recommended fasteners
• Retain original mounting hardware unless the new handle explicitly includes replacements