Admiral Dishwasher Parts

I replaced the gasket. Removing the old one was not easy. I used a razor knife to cut out most of it. And then I used rubbing alcohol to soften the remaining glue and scrapped it out with a small blade screwdriver Read more

• Leaking

After discovering your web site and reading of others issues I ordered a door seal (my old one was a little short on the right side) a detergent door grommet, and the 2 water deflectors ( I decided to cover all the bases while I was at it. Very simple job with the information provided on your web site. I certainly have the confidence to tackle other appliance repair now. Read more

• Door latch failure

After finding the model number for my dishwasher, I looked on line for the part and ordered it. The part arrived next day. I was a little hesitant to tackle it myself, as I am a 67 year old female. However I decided I could do it and was all set until I found out that I needed a Torx screwdriver. This however was not going to stop me. At a trip to my neighbor I was able to find bit for a drill that would let me remove one screw. The next stop was to my favorite hardware store where I... Read more

Dishes were 'gritty' with an almost invisible coating of specks smaller than grains of salt. Prior to ordering parts, I had to determine which part(s) needed replaced and which could benefit from a good cleaning. After viewing Appliance Parts Pros YouTube Videos, I removed the Main Manifold (snaps right off) including the Top Spray Arm. I discovered the Flappers of the Docking Station (AP6009888) were worn out and/or missing. I removed the Docking Station simply by popping the old one off... Read more

Replaced them - loved the videos Read more

• Will not fill with water

I figured the valve that allowed water into the dishwasher was bad, or some controlling function of this process. I went online, typed in model number and had a full exploded view of the parts in my dishwasher. I ordered the inlet solenoid valve as the first step to what may be wrong. Turns out this part was the problem. With the online video it made replacement a breeze. Thank you APP for the RIGHT part AND instructions. Online purchasing and delivery are easy and timely. Read more

Tipped the dishwasher on to its front, loosened the drain hose clamp and pulled the hose off. Then unscrew the fill hose which looks like a garden hose adapter. Cut the zip tie on the drain hose and take note of how both hoses are routed, then pull both hoses out the back of the dishwasher. Insert new hoses and route them correctly and hook everything back up. Couple of notes, I didn't have to take off the outer cabinet to do this repair. Get plenty of towels because a lot of water can get... Read more

• Leaking

About a month ago, a sporadic drip was noticed on right hand bottom corner of dishwasher. Puddle would vary in size but nothing major. My first inclination was to change the door gasket (~$35 at a major online retailer) as this seemed reasonable to me and was a straightforward fix. Next wash cycle, no drip. However the drip returned the wash cycle after that, however this time at a different spot along the bottom of dishwasher door. I then replaced a deteriorated corner door seal (~$17... Read more

I first wanted to get the dishwasher running, before ordering the spring links. So I disassembled the pump / motor assembly to determine the reason the motor would not start. My wife cleaned all of the parts in the pump assembly. I took the motor apart and discovered that the lower bearing ( a sleeve type bearing) was dry and dirty, and was the culprit for the motor seizing. I cleaned up the bearing and lubricated it with SAE 20W. I also packed felt inside the cavity adjacent to the bearing.... Read more

Normally when you let go of the dishwasher door partly open it would stay in that position. But lately when you let go of the door it would fall to the fully open position. Turns out this little cable was broken one one side. Just puss the dishwasher slightly out of the cabinet and you can replace the cable in minutes. It is just held in place with a spring. Read more

Got the make and model. Put it in your web site order form and watched the video. The part came the replacement part was made and job done. Thanks. Great parts, fast shipment and again job done. Read more

Dishes were 'gritty' with an almost invisible coating of specks smaller than grains of salt. Prior to ordering parts, I had to determine which part(s) needed replaced and which could benefit from a good cleaning. After viewing Appliance Parts Pros YouTube Videos, I removed the Main Manifold (snaps right off) including the Top Spray Arm. I discovered the Flappers of the Docking Station (AP6009888) were worn out and/or missing. I removed the Docking Station simply by popping the old one off... Read more

• Will not fill with water
• Leaking

SCREWED IT ONTO FAUCET Read more

Without knowing exactly what broke I ordered 2 springs and 2 door spring links. I knew the door springs were weak and a parts man told me many years ago to always replace BOTH springs or the one you didn't replace will soon break. It is a simple procedure, just remember how the springs/links are attached. make a simple drawing or take a picture should you need it. I watched two "how to" video's which made it look harder to do than it really is. Turn the circuit breaker off and turn the... Read more

• Not cleaning dishes properly

Searched on this site and found likely cause and solution to problem. After watching APP video, I was able to remove dishwasher filter and confirm clogged filter. Ordered the new part and it was shipped quickly. Reinstalled it per video instructions and it worked perfectly! Thank you APP.com for making me look like an appliance repair expert on this and several other projects. This has saved me lots of money over the last few years, and kept my slightly older appliances in working order and... Read more

Motor shaft was stripped, replaced with new shaft from Motor Seal Kit. Impeller was also cracked, so replaced it as well. I did run in to a small problem, the chopper blade was pressing against the metal grate on the piece that goes back over the motor seal. I spent about an hour messing with it, but thought maybe once it's all together it'll be fine. When you screw the impeller on, it pushes down the seals, which pushes down the chopper blade. Video on Motor Seal Kit page made it an... Read more