Admiral Refrigerator Gasket & Seal

This fresh food door gasket seals the refrigerator compartment door to keep cold air in and warm air out. Replacing a worn gasket restores a tight seal, improves temperature stability, and helps prevent condensation and frost around the door.

• Seals the perimeter of the fresh food (refrigerator) door to limit air leaks
• Helps maintain proper interior temperature and efficiency
• Typical symptoms of failure: door not closing or sealing fully; visible tears, gaps, or warping
• May cause moisture, sweating, or frost near the door gasket area

• Disconnect power before servicing
• Warm and relax the new gasket (soak in warm water or use low heat) to ease installation; do not overheat
• Clean the door's gasket channel; install starting at the corners and ensure even seating all around
• Close the door and check for uniform contact; use a paper-slip test to confirm the seal

This door gasket seals the refrigerator/freezer door to help maintain proper temperature and reduce energy loss. A direct-fit replacement that restores the magnetic seal for better cooling performance. What it does:

• Re-establishes a tight seal around the door to keep cold air in and warm air out
• Helps reduce frost buildup and moisture inside the compartment
• Improves cooling efficiency and may reduce excessive run time from a failing seal
• Stops drafts and prevents food spoilage caused by a poor door seal

• One door gasket

• Clean the door frame and remove old gasket before installing the new one
• Warm or flex the gasket as needed for easier positioning; ensure the magnetic seal seats evenly around the perimeter
• Check hinge alignment and door closing after installation to confirm a complete seal
• Follow appliance power-off and safety precautions; refer to the appliance manual for model-specific instructions

This is the rear crisper seal that fits along the back edge of the refrigerator crisper compartment to help maintain the crisper enclosure and reduce air leakage. It restores a tighter seal for better humidity control and food storage. What it does:

• Replaces a worn or torn rear crisper gasket to help reduce cold air loss from the crisper area
• Helps maintain crisper humidity so produce stays fresher longer
• Prevents gaps that can cause uneven cooling or frost build-up near the drawer
• Can reduce draft noise or rubbing caused by a damaged seal

• One rear crisper seal (matches OEM part number)

• Remove the crisper drawer to access the rear seal before replacing
• Peel out the old seal and press the new seal firmly into the gasket channel; ensure an even, continuous fit
• Avoid using sharp tools that could damage the cabinet or new seal
• Unplug the refrigerator or switch off power if needed for safe access to nearby components

Condenser seal that cushions and seals the condenser assembly to the cabinet, helping reduce vibration and directing airflow for more consistent cooling performance and quieter operation. What it does:

• Cushions the condenser to reduce vibration and rattling noises
• Seals the condenser perimeter to help direct airflow through the condenser coils
• Helps prevent rubbing and abrasion between the condenser and cabinet
• A worn or missing seal can contribute to increased noise or reduced cooling efficiency

• Disconnect power to the appliance before beginning any repair
• Remove the lower access panel or kickplate to access the condenser area
• Peel out the old seal and press the new seal fully into the channel or onto the condenser flange for a snug fit
• Inspect condenser fins and surrounding parts during installation; do not use solvents or unapproved adhesives

This evaporator cove seal is the replacement gasket that helps keep the evaporator compartment sealed for efficient cooling and proper defrost drainage. It restores the evaporator cove barrier to help maintain temperature consistency. What it does:

• Seals the evaporator cove to limit air exchange between the evaporator area and the fresh food/freezer compartments
• Helps direct defrost water to the drain path and reduce water pooling inside the appliance
• Reduces frost buildup and cold-air loss around the evaporator area
• Commonly replaced when you see frost/ice buildup, interior water leaks, or uneven cooling

• Disconnect power before starting any repair to avoid shock or injury
• Remove shelves/food and allow the appliance to defrost if ice is present before replacing the seal
• Inspect the evaporator cover and mating surfaces; clean and dry surfaces for a proper seal
• Seat the seal evenly around the cove; avoid overstretching or sharp tools that could damage the gasket