Admiral Refrigerator Hinge Parts

A replacement center hinge pin that secures the refrigerator door at the center hinge assembly to restore proper pivoting and alignment. Use this pin to correct door sag or uneven closing caused by a worn or bent hinge pin. What it does

• Secures the door to the center hinge so the door can pivot smoothly.
• Restores proper door alignment and helps the door seat evenly against the cabinet.
• Commonly used to address door sag, rubbing, uneven gaps, or difficulty closing.
• Works as a direct replacement for the center hinge pivot in the hinge assembly.

• Always disconnect power to the appliance before servicing to avoid electrical hazards.
• Support the door and follow the appliance manufacturer's hinge removal steps before removing or installing the pin.
• Inspect surrounding hinge components (bushings, brackets) for wear while replacing the pin; replace as needed.

A non-metal shim used to stabilize and level your appliance for quieter, more reliable operation. Simple, low-profile support that helps correct minor height and balance issues so doors and drawers align and appliances sit securely. What it does:

• Adds thin, non-metallic spacing under feet or frame to correct slight height differences
• Helps stop rocking or tipping that can cause noise, vibration, or misaligned doors
• Supports even weight distribution to reduce uneven wear on adjustable legs
• Useful when adjusting leveling feet can't fully correct a gap or tilt

• Place shim under the appliance foot or frame where additional height or support is needed
• Re-check appliance level and stability after installing; add/remove shims as required
• Use with care to avoid creating instability; pair with proper leveling adjustments

This door hinge restores smooth, controlled door movement and a tight, secure close. Replace a bent or worn hinge to correct doors that sag, bind, or won't stay closed, helping your appliance seal properly and perform as designed.

• Supports and guides the door through its full range of motion
• Helps keep the door aligned so the gasket compresses evenly for a proper seal
• Controls closing action and stop position to protect the door and frame
• Common symptoms: door won't close flush, sags, pops open, or moves roughly/squeaks

• Disconnect power at the breaker and allow the appliance to cool completely before servicing
• Support the door; follow the service manual for door removal. Engage hinge locks or use retaining pins if equipped
• Transfer any screws/brackets from the old hinge to the new and install on the correct side if the design is side-specific
• Ensure the latch engages and the gasket seals uniformly all around

This door hinge is a direct-fit replacement that helps the appliance door open and close smoothly and stay properly aligned to prevent rubbing or gaps. Durable construction restores reliable door movement and seal engagement. What it does:

• Supports and pivots the appliance door so it opens and closes correctly
• Maintains correct door alignment to help the gasket seal fully
• Reduces sagging, sticking, or uneven door gaps that can affect performance
• Works with the existing hinge mount points and hardware

• One door hinge

• Disconnect power and empty the door before starting to avoid injury or damage
• Use the OEM mounting screws and follow turning sequence to re-align the door
• Tighten fasteners securely, then cycle the door and check for proper seal and operation

A small replacement closure shim that helps align and secure a closure/trim piece on select appliances, restoring proper fit and reducing rattles, rubbing, or gaps for quieter, more reliable operation. What it does:

• Positions and supports the closure/trim so panels and doors close evenly.
• Helps stop rubbing, misalignment, or minor gaps that can cause noise or poor sealing.
• Serves as a non-electrical spacer/aligner where the original shim has worn or broken.
• Useful when cosmetic trimming or closure pieces feel loose or shift during use.

• Disconnect power to the appliance before starting any repair or accessing panels.
• Access location may require removing the related trim, panel, or door—refer to the appliance diagram or service manual.
• Handle small plastic parts carefully; align the shim before fastening to avoid breakage.

A replacement hinge bushing that supports and cushions a refrigerator/freezer or appliance door hinge for smoother movement and reduced wear. Restores correct hinge alignment and helps prevent noisy or stiff door operation. What it does:

• Cushions metal-to-metal contact at the door hinge to reduce wear and vibration
• Helps the door swing smoothly and maintain proper alignment
• Reduces rubbing, scraping noises, and uneven door movement
• Supports hinge pin function to extend hinge life

• Basic hand tools required; appliance diagrams for hinge access
• Remove power or unplug the appliance before servicing where applicable
• Handle door panels carefully; support door weight to avoid damage or injury

This upper door hinge secures the top pivot for the appliance door, keeping the door aligned and allowing smooth opening and closing. Replaces a worn or damaged upper hinge to restore proper door fit and operation. What it does:

• Supports the top of the door and provides the pivot point for opening and closing
• Helps maintain proper door alignment and an even seal
• Commonly used when a door sags, drags, or shows an uneven gap
• Prevents excessive wear on adjacent hinge components and door hardware

• One upper hinge

• Disconnect power and empty or secure the door before beginning work
• Always support the door while removing or installing the hinge to prevent falling or damage
• Use correct replacement screws and hardware as shown in the OEM diagram