Admiral Washer Dryer Combo Parts

This drain hose routes wastewater from the appliance to the household drain, helping remove used water after a cycle. It replaces a damaged, kinked or leaking hose to restore proper draining and prevent puddling. What it does:

• Carries discharge water away from the appliance during drain cycles
• Restores proper draining when the original hose is cracked, split or leaking
• Helps prevent backups and standing water inside the appliance
• Works with the appliance's pump and drain system to maintain normal operation

• One replacement drain hose

• Disconnect power and water before starting any work
• Verify hose routing and secure clamps to prevent kinks and leaks
• Inspect and replace any worn clamps or fittings as needed
• After installation, run a short cycle and check for leaks and proper drainage

Spesc: #12 pozi - drive

This Torx-head screw set replaces worn, stripped or missing Torx fasteners used throughout the appliance to keep panels and components securely fastened. Restoring proper fasteners reduces vibration and prevents loose parts. What it does:

• Secures control panels, trim pieces or internal components that use Torx-head screws
• Replaces damaged or corroded Torx screws that can cause rattling or misalignment
• Helps restore proper fit and finish after repairs or disassembly
• Uses a Torx drive for a more secure torque transfer than standard Phillips heads

• Unplug the appliance or disconnect power before starting any repair
• Use the correct-size Torx driver to avoid stripping the screw head
• Tighten screws snugly but avoid over-torquing to prevent thread or part damage
• Keep removed screws organized and compare to the new set before installation

This hex-head screw secures the bearing insert in place, maintaining correct alignment and stable operation. Replacing a damaged or missing screw restores secure bearing retention and reduces noise or wobble. What it does:

• Holds the bearing insert assembly firmly to prevent movement and misalignment
• Helps stop excessive vibration, noise, or drum wobble caused by a loose bearing insert
• Maintains correct spacing so the bearing and shaft rotate smoothly
• Replaces stripped, rusted, or missing fastening hardware for reliable operation

• Unplug the appliance or disconnect power before beginning any repair
• Use the proper hex driver and size to avoid stripping the head
• Tighten securely but do not overtighten; overtightening can deform the insert or housing
• Inspect the bearing insert and surrounding parts; replace any damaged components for a lasting repair

This exhaust vent extension restores proper exhaust airflow by lengthening or adapting the appliance exhaust outlet to the vent duct. It helps maintain safe ventilation and reduces backpressure that can cause poor performance or odors. What it does:

• Extends or adapts the appliance exhaust outlet to reach the home vent duct
• Directs exhaust airflow to reduce backflow and help prevent overheating
• Helps resolve symptoms like weak venting, lingering odors, or unusual appliance cycling
• Provides a stable connection point for the exhaust duct to improve sealing and airflow

• Turn off and disconnect power (and gas if applicable) to the appliance before installing.
• Use proper fasteners and high-temperature-rated duct tape or clamps as recommended by the appliance manufacturer.

A small hex nut used to secure components and fasteners on compatible Whirlpool appliances. Replaces a worn or missing nut to restore proper part retention and reduce noise or loose fittings. What it does:

• Secures panels, brackets, or components that use a matching bolt or stud
• Helps prevent rattling, vibration, or parts coming loose during operation
• Restores a proper threaded connection when the original nut is stripped or missing
• Works wherever the correct thread size and profile are required

• Unplug the appliance or disconnect power before starting any repair
• Use the correct-size wrench or socket to avoid rounding the nut
• Tighten securely but avoid overtightening, which can strip threads or crack parts
• Inspect mating bolts/studs and replace if damaged

A replacement mounting screw used to secure appliance panels and components. This genuine-style fastener restores proper fit and prevents loose or rattling parts for many Whirlpool appliances. What it does:

• Fastens panels, trim, brackets, or components to the appliance frame
• Restores secure attachment when original screw is missing, stripped, or damaged
• Helps eliminate rattling, vibration noise, and loose-fitting parts
• Matches OEM fit and function when the correct part number is used

• Disconnect power (and water, if applicable) before servicing the appliance.
• Use the correct screwdriver or driver bit to avoid stripping the head; do not overtighten.
• Replace only with the exact part number to ensure correct fit; keep removed hardware organized for reassembly.