Ariens Lawn Mower Parts

This clutch cable kit is an authentic OEM replacement part for a riding lawn mower or tractor. The clutch cable connects to the idler arm located in the lower deck of a mower and allows the operator to manually engage or disengage the blades. The clutch cable runs up through the steering block and into the front display so that the operator can easily access the clutch. If a clutch cable becomes jammed or tenses up, it will be difficult to depress. If the operator tries to depress the clutch cable without realizing that it is jammed, the clutch cable will snap. The most obvious sign of a snapped clutch cable is that the clutch gives little resistance and the blade cannot be engaged. To change a clutch cable, use a socket set to remove the fuel tank and gain access to the cable. A pair of needle nose pliers is also recommended. This replacement part is compatible with Weed Eater, Husqvarna, Ryobi, and Poulan appliances and comes sourced from its original manufacturer. This part includes a clutch cable and a zip tie.

Flat idler pulley for riding mowers and lawn tractors. Works with the belt to transfer power from engine to drive system. Replace if cracked or worn.

Replaces cracked, rusted, or damaged muffler on riding mowers. Reduces exhaust noise and prevents sparks from igniting debris on the ground.

This is a genuine OEM replacement drive V-belt for a riding lawn mower. The drive V-belt attaches to the drive pulley and transfers rotational motion from the transmission to the mower blade. This causes the blade to then spin and cut grass. By using a belt to transfer motion, the engine does not have to work as hard to spin multiple parts, meaning that it runs more efficiently. Drive V-belts are made of a rubber composite material that will begin to fray and stretch over time. Due to continuous motion, these belts absorb a lot of wear and tear, and if left for too long, they can eventually snap and leave the mower blade non-functional. Therefore, it is wise to check the condition of a V-belt during regular maintenance. As soon as it appears to be wearing away, replace it with a new part using a nut driver and screwdriver. When detaching the lower deck, be sure not to lose the bolt clips, as they are required for reassembly. As a high-quality replacement part, this drive V-belt is directly sourced from its original manufacturer. It is compatible with riding lawn mowers made by Husqvarna, Poulan, Craftsman, and Jonsered. This part ships individually.

A V-belt is responsible for transmitting energy. It is made from a thick and sturdy rubber material. It features grooves for improved traction and measures ½ x 95-1/2. A worn-down v-belt can lead to inefficient energy loss, and therefore poor performance. Installing this v-belt requires pliers and a wrench. First, the spark plug wire needs to be removed. Then, position the mower deck to the lowest possible level. Move the machine's blade engagement level to OFF. Remove the belt found from the engine pulley. Don't forget to take out the bow-tie pins and blade engagement cable as well. Remove the bolt from the pulley cover and loosen the nuts found at the idler pulley. Put the new belt and then tighten the nuts on the idler pulleys. The deck can now be re-assembled to its original position. This Husqvarna 532144959 V-Belt OEM Replacement can help keep a lawnmower in top condition. This genuine Husqvarna made V-belt is specifically for driving the blades on a lawnmower. It is compatible with Ariens, Craftsman, Poulan Pro, Dixon, and Husqvarna mowers. This V-belt is sold individually.

Mower won't start or starter doesn't engage? This ignition switch activates your riding mower's electrical system. Simple DIY repair in under 30 minutes.

Shoulder bolt that attaches the suspension arm to the wheel bracket on riding mowers and tractors. Replace if bolt is stripped, worn, or missing.

Replacement muffler for front-engine lawn tractors. Installs on the engine exhaust system. Replace if cracked, rusted, or leaking exhaust gases.

Mandrel spacer washer for riding mowers and lawn tractors. Installs between drive pulleys to maintain proper alignment and spacing. Replace if worn or missing.

Secures the mower blade to the spindle on riding mowers and tractors. Replace if bolt is stripped, washer is damaged, or hardware is missing.

This genuine Husqvarna fuel cap provides cover and protection to the hole into which engine oil is dispensed on certain lawn mowers, lawn tractors, and snowblowers. This fuel cap should remain closed when the appliance at hand is not in use in order to prevent leakage.If the engine of a small engine appliance is suffering from frequent leakages, there could be damage in the fuel cap that is causing the leaks. A fuel cap could also become misplaced. If the cap is broken or lost, it must be replaced immediately before using the small engine appliance again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. This fuel cap is compatible with the following brands: Husqvarna, Poulan, Ariens, and Craftsman. This part is sold individually.

Hardened washer for lawn tractors and riding mowers. Installs with bolts to redistribute pressure and prevent loosening. Replace if worn or missing.

Idler pulley for lawn tractor mower decks. Creates tension on the drive belt. Replace if worn, cracked, or damaged from debris accumulation or impact.

Idler pulley for riding mowers and tractors. Maintains proper belt tension for drive system. Replace if pulley is cracked, worn, or spinning rough.

Brake linkage assembly for riding mowers and lawn tractors. Replaces worn, bent, or broken brake linkage brackets. Essential for proper brake operation.

Replacement steering wheel for riding lawn tractors and mowers. Installs on the steering column adapter to control mower direction and movement.