Parts for Frigidaire CGGF3032MFA: 03 - Backguard Parts

Shield for electric ranges. Protects internal components from heat and debris. Replace if cracked, bent, or missing to maintain proper coverage.

Replace your gas range heat shield if it's cracked, warped, or missing. This protective shield installs between burner components to guard against heat damage.

This replacement panel forms the finished control area of your appliance. It provides a sturdy mounting surface for the user interface and protects the electronics behind it, restoring proper alignment, appearance, and protection when the original panel is damaged. What it does:

• Covers and protects the control compartment and wiring
• Provides mounting points for the control board, switches, knobs, and/or overlay
• Keeps controls aligned and secure for proper operation
• Common signs it's needed: dents, cracks, broken tabs, sharp edges, or controls that won't sit flush or stay secured

• One panel

• Disconnect power at the breaker; shut off gas supply if applicable
• Wear cut-resistant gloves—panel edges can be sharp
• Transfer existing control components, brackets, and hardware from the old panel to the new one; label wires or take photos for reference
• All screws and harness connections are secure before restoring power and testing

Fix F30 errors, blank displays, or unresponsive oven controls with this electronic control board. DIY-friendly repair in under an hour with basic tools.

Fix faded or bubbled button labels on your range control panel. This overlay restores clear markings in 5-15 minutes with basic tools and a screwdriver.

Trim cap for electric ranges. Covers and finishes control panel or body edges. Replace if cracked, broken, discolored, or missing for a complete look.

The Knob is an OEM replacement part for Frigidaire ranges. It controls temperature settings on gas or electric coil burners. The knob measures approximately 2 inches in diameter.

Causes of a bad knob can include wear and tear from daily use, chemicals damaging the lettering/graphics, or constant exposure to heat cycles reducing stability over time.

Symptoms of a bad knob include:

• Slippery or uneven feel making temperature selections uncertain
• Loose attachment allowing unintended movement between settings 
• Faded or missing labeling obscuring correct burner identification
• Distortion compromising accurate calibration of heat levels

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This trim is a decorative finish piece for select ranges and wall ovens. It covers gaps and raw edges for a clean look and helps keep adjacent panels properly seated when the original becomes cracked, bent, or missing.

• Provides a finished appearance by covering exposed edges or gaps
• Helps maintain alignment of nearby panels or glass
• Replace if cracked, warped, missing, or no longer seats securely
• Common symptoms include loose/rattling panels and exposed or sharp edges

• Disconnect power; for gas models, also shut off the gas supply
• Wear gloves—edges can be sharp
• Remove old trim and transfer/reuse original screws or clips
• Align the new trim and secure with existing fasteners; confirm proper fit before reassembly

Shield for gas ranges. Protects internal components from heat and debris. Replace if cracked, bent, or missing to maintain proper appliance protection.

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.