Parts for Frigidaire CGGF3032MFC: 03 - Backguard Parts

This replacement panel forms the finished control area of your appliance. It provides a sturdy mounting surface for the user interface and protects the electronics behind it, restoring proper alignment, appearance, and protection when the original panel is damaged. What it does:

• Covers and protects the control compartment and wiring
• Provides mounting points for the control board, switches, knobs, and/or overlay
• Keeps controls aligned and secure for proper operation
• Common signs it's needed: dents, cracks, broken tabs, sharp edges, or controls that won't sit flush or stay secured

• One panel

• Disconnect power at the breaker; shut off gas supply if applicable
• Wear cut-resistant gloves—panel edges can be sharp
• Transfer existing control components, brackets, and hardware from the old panel to the new one; label wires or take photos for reference
• All screws and harness connections are secure before restoring power and testing

Restore proper oven operation with this electronic control board. It manages bake and broil functions and the display, helping bring back consistent heating and a readable clock/timer when the original control fails. What it does

• Directs power to bake and broil circuits based on user selections
• Controls oven temperature cycling using sensor feedback
• Drives the digital clock, timer, and status display
• Typical failure symptoms: dead or dim display, oven won't start or heat, unresponsive controls, intermittent operation, or error beeping

• 1 electronic control board assembly

• Disconnect power at the breaker before servicing
• Access the control behind the control panel; remove panel/console screws to reach it
• Move wires one at a time to the new board; photograph connections and reuse brackets/insulators as needed
• Handle by the edges and protect from static; for any required setup/calibration after installation

This control panel overlay is the front label for the electronic clock/timer. Replace it to restore clear button markings and a factory look when the original graphics become faded, bubbled, or damaged.

• Labels the buttons and display areas on the electronic control
• Provides a clean, finished appearance and helps protect the surface from light wear
• Common symptoms: faded or peeling graphics, bubbling, cracks, or unreadable labels
• Often replaced along with the electronic control so the button layout matches

• Disconnect power to the appliance before servicing
• Remove the control panel/backguard as required by your model; gently warm and peel off the old overlay and clean any adhesive residue
• Align the new overlay with display and button openings; press from the center outward to set without bubbles
• Avoid touching the adhesive backing; allow proper adhesion before reassembly and restoring power

The Knob is an OEM replacement part for Frigidaire ranges. It controls temperature settings on gas or electric coil burners. The knob measures approximately 2 inches in diameter.

Causes of a bad knob can include wear and tear from daily use, chemicals damaging the lettering/graphics, or constant exposure to heat cycles reducing stability over time.

Symptoms of a bad knob include:

• Slippery or uneven feel making temperature selections uncertain
• Loose attachment allowing unintended movement between settings 
• Faded or missing labeling obscuring correct burner identification
• Distortion compromising accurate calibration of heat levels

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

This trim is a decorative finish piece for select ranges and wall ovens. It covers gaps and raw edges for a clean look and helps keep adjacent panels properly seated when the original becomes cracked, bent, or missing.

• Provides a finished appearance by covering exposed edges or gaps
• Helps maintain alignment of nearby panels or glass
• Replace if cracked, warped, missing, or no longer seats securely
• Common symptoms include loose/rattling panels and exposed or sharp edges

• Disconnect power; for gas models, also shut off the gas supply
• Wear gloves—edges can be sharp
• Remove old trim and transfer/reuse original screws or clips
• Align the new trim and secure with existing fasteners; confirm proper fit before reassembly

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.