Parts for Kenmore 790.94243315 (79094243315, 790 94243315): Backguard Parts

Protective cover that shields the range door hinge assembly from debris and damage. Replace if cracked, broken, or missing to restore a clean finished look.

Burner won't turn off or element light stays on? This range burner control switch regulates temperature and power. Moderate DIY repair, 30-60 minutes.

Signals when your range burners or oven are active. Replace when light fails to illuminate or stays on constantly. Confirm fit with your model number.

End cap for electric and gas ranges. Covers and protects the end of the control panel or trim. Replace if cracked, broken, or missing for a complete look.

End cap for electric and gas ranges. Covers exposed edges on the cooktop or control panel. Replace if cracked, broken, or missing for a finished look.

Range won't heat or respond to controls? This electronic control board restores oven function when the controller fails. Moderate DIY repair.

Protective plastic overlay for your range control panel. Replaces cracked, discolored, or worn overlays from heat exposure or repeated cleaning.

Snap-in plug cap seals unused cabinet or component openings on your range. Replace if cracked, missing, or worn to keep out moisture and debris.

This is a replacement control knob for appliance control panels. It restores a worn, cracked, or missing dial so you can set temperature, timer, or element settings with a secure grip and clear pointer. What it does

• Fits onto a splined control shaft to provide user control of oven, range, or cooktop functions.
• Replaces cracked, faded, or loose knobs that are hard to turn or don't stay set.
• Restores a clear pointer for accurate setting selection and safer operation.
• Works as a direct-fit replacement when matched to the correct appliance control shaft.

• One control knob (single knob included)

• Turn power off to the appliance before servicing; follow all safety precautions.
• Pull old knob straight off the control shaft and press the new knob onto the shaft until fully seated.
• Do not force if the knob does not align; confirm shaft splines match the knob before installation.

Indicator light lens covers and protects the burner signal light on your range. Replace when cracked, discolored, or missing. Confirm fit with your model.

Replace a faulty surface element switch if your electric range burner won't heat, won't turn off, or cycles incorrectly. Direct replacement part.

Burner stuck on high or won't adjust heat levels? This infinite switch controls your range's top burner temperature settings. Moderate DIY repair.

Burner stuck on high or won't heat? This surface element switch controls temperature for electric range burners. DIY repair in under 30 minutes.

Replace a cracked, broken, or missing shield on your range. This protective guard component installs to safeguard internal parts from damage or wear.

This truss-head machine screw secures a switch to its mounting bracket or panel. Replacing a worn or missing screw restores a solid, aligned switch fit for reliable operation.

• Fastens the switch body to a bracket or chassis panel
• Helps keep the switch aligned for consistent actuation
• Replaces stripped, corroded, or missing mounting hardware
• Common symptoms: loose or wobbly switch, misalignment, rattling or vibration around the switch area

• Disconnect power to the appliance before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Verify thread size and length match the original hardware
• If multiple screws secure the switch, replace them in a consistent pattern to maintain alignment

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.