Parts for Tappan TEF326FBB: 03 - Backguard Parts

Replace your range's backguard shield if the rear wall panel is cracked, dented, or damaged. Protects the wall behind your cooktop and covers wiring.

Replace a cracked or missing right-hand shield end cap on your range. This protective trim piece covers the end of the range shield for a complete finish.

Left-hand end cap shield for range oven doors. Replaces cracked, broken, or missing caps that protect the door edge. Installs on the left side of the door.

Signals when your range burners or oven are active. Replace when light fails to illuminate or stays on constantly. Confirm fit with your model number.

Right-hand support plate for range backguard. Replaces cracked, broken, or missing mounting brackets. Secures backguard panel to range body.

Black right-hand endcap for range side panels. Replaces cracked, broken, or missing endcaps. Restores finished appearance to range exterior trim.

Left Hand Endcap - Color: Black

Black clock overlay that labels the electronic oven control panel buttons. Replace worn, peeling, or faded overlays to restore clear markings and readability.

The Clock is an OEM part for Frigidaire ovens and ranges. It is the central electronic component that regulates and monitors oven functions such as bake, broil, convection, temperature controls, and timers.

Causes can be failures in the integrated circuitry, damaged connectors or traces on the board, or water or other environmental damage over time.

Symptoms of a clock include:

• Failure of oven elements to heat properly
• Unresponsive or inaccurate temperature displays
• Irregular timed baking or errors flashing
• Problems with convection or baking modes
• Power issues such as the oven not turning on

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Mounting bracket that secures the clock assembly to your range control panel. Replace if the original is bent, broken, or missing during clock repairs.

The Rocker Switch is an OEM part for Frigidaire ranges and ovens. It is responsible for turning the interior oven light on and off. The light switch allows visibility of the oven cavity for viewing food during the cooking process.

Causes can include normal wear and tear over time, exposure to heat inside the oven cavity, or accidental damage.

Symptoms of a bad oven light rocker switch include:

• The oven light failing to illuminate when the door is opened
• The light remaining on even when the door is closed
• An inconsistent or flickering oven light
• The switch itself becoming loose, cracked, or non-responsive

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Replace your cracked, worn, or missing range control knob. This single dial restores easy temperature control and accurate settings for your oven.

Indicator light lens covers and protects the burner signal light on your range. Replace when cracked, discolored, or missing. Confirm fit with your model.

Burner stuck on high or won't heat? This surface element switch controls temperature for electric range burners. DIY repair in under 30 minutes.

Burner won't turn off or stuck on high? This surface element switch controls heat settings for large burners. Moderate DIY with panel removal.

Replace a cracked, broken, or missing shield on your range. This protective guard component installs to safeguard internal parts from damage or wear.

This truss-head machine screw secures a switch to its mounting bracket or panel. Replacing a worn or missing screw restores a solid, aligned switch fit for reliable operation.

• Fastens the switch body to a bracket or chassis panel
• Helps keep the switch aligned for consistent actuation
• Replaces stripped, corroded, or missing mounting hardware
• Common symptoms: loose or wobbly switch, misalignment, rattling or vibration around the switch area

• Disconnect power to the appliance before servicing
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Verify thread size and length match the original hardware
• If multiple screws secure the switch, replace them in a consistent pattern to maintain alignment