Parts for Whirlpool K45SS: 03 - Base And Pedestal, Literature Parts

This factory fastener secures appliance panels, brackets, and components. Replacing a missing or worn screw restores a tight, rattle-free fit and helps keep parts aligned as designed for reliable operation. What it does:

• Fastens specified components to maintain alignment and structural integrity
• Helps reduce vibration, noise, and loosening from normal use
• Replace if stripped, corroded, or missing
• Common symptoms include loose or rattling parts and hardware that won't tighten

• One screw

• Disconnect power and shut off water or gas before servicing
• Match location and orientation; replace one-for-one with the original
• Start threads by hand to avoid cross-threading; use the correct driver bit and do not overtighten
• Inspect related clips/inserts; replace if damaged to ensure proper retention

The Cap-Screw is an OEM component specifically designed for Whirlpool mixers. It contains precision mixing mechanisms that allow users to easily and effectively blend, whip, or beat ingredients.

Symptoms of a bad Cap-Screw include:

• Difficulty turning on or selecting speeds
• Excessive noise or vibration during use
• Inconsistent mixing performance
• Leaks into electrical components

Causes of failure can be faulty power switches, worn gears, damaged housing or bowls, or deterioration of internal wiring over time.

This Cap-Screw is also compatible for use with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, and select Kenmore.

The Foot is an OEM part for Whirlpool stand mixers. This component is designed to provide stability and support to the mixer, ensuring it remains steady during operation. Positioned at the base of the mixer, the foot helps to prevent movement and vibration, which can enhance the efficiency of mixing and protect your countertop from scratches.

Symptoms of a failing Foot include:

• The mixer wobbling or moving excessively during use
• Increased noise or vibration when the mixer is running
• Visible wear, cracks, or deformation of the foot pad
• Scratches or damage to the countertop surface beneath the mixer

Causes of a bad foot can include prolonged use that wears down the material, exposure to heat or kitchen chemicals that degrade the foot, or physical damage from moving or storing the mixer.

This OEM Whirlpool part is also compatible with KitchenAid stand mixers.

This pedestal feet assembly provides the lower support and leveling for a laundry pedestal, helping keep the pedestal stable and aligned beneath the washer or dryer. Designed to restore proper support and reduce rocking. What it does:

• Replaces damaged or worn pedestal feet that cause rocking, uneven height, or instability
• Provides adjustable support to help level the pedestal on uneven floors
• Protects floors by maintaining proper pedestal alignment and preventing scraping
• Restores safe, secure support for appliances installed on the pedestal

• Follow the appliance and pedestal manufacturer instructions; have a second person or proper support to prevent tip-over when removing or installing the pedestal
• Ensure the appliance is powered off and disconnected from utilities if appliance removal or repositioning is required
• Use basic hand tools; confirm all fasteners are tightened securely after installation

This replacement mixer pedestal restores the base support and appearance of compatible stand mixers, providing a stable platform and finished look. Use it to replace cracked, chipped, or damaged pedestals that affect mixer stability. What it does:

• Replaces a worn or damaged pedestal to help stabilize the mixer and reduce wobble
• Restores the exterior finish where the original pedestal is cracked, chipped, or broken
• Provides the proper mounting surface for the mixer head and internal components
• Helps prevent further wear or damage caused by an unstable base

• One mixer pedestal (white)

• Disconnect power and remove the mixer from any mounting before attempting replacement
• Follow OEM disassembly steps for accessing and removing the pedestal; keep fasteners for reinstallation
• Use basic hand tools; avoid forcing parts and protect finished surfaces from scratches

The Hinge Pin is an OEM part for Whirlpool stand mixers. This part allows the tilt head of the stand mixer to pivot smoothly, enabling easy access to the mixing bowl and attachments. The hinge pin ensures that the tilt head remains securely attached while providing stability during operation.

Causes of a bad hinge pin can include general wear and tear, corrosion from exposure to moisture, or damage due to heavy use.  

Symptoms of a bad hinge pin include:

• Difficulty in raising or lowering the tilt head
• Tilt head not locking into place properly
• Unusual wobbling or instability during mixing
• Squeaking or grinding noises when adjusting the tilt head

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

This latch, link, and lever assembly restores proper latching action so the door or lid closes securely and the appliance can run as intended. It replaces worn or broken linkage that can prevent the latch from engaging.

• Connects the latch to its operating lever to enable smooth open/close action
• Helps resolve issues like a door/lid that won't latch, pops open, or won't start due to an unlatched condition
• Prevents intermittent cycle interruptions caused by a weak or misaligned latch linkage
• Durable components designed to maintain consistent latch engagement

• Unplug or disconnect power before servicing
• Access the latch area per your model's service information
• Note linkage orientation during removal to ensure correct reassembly
• Test latch engagement and operation before returning to service

This latch secures the appliance door and helps ensure a proper close for normal operation. It replaces a worn or broken latch to restore reliable door engagement and user safety. What it does:

• Holds the door closed so the appliance can operate as intended
• Replaces a damaged or broken latch that prevents the door from staying shut
• Helps restore proper alignment and engagement of the door mechanism
• Can reduce door rattling or intermittent closing issues

• Latch

• Disconnect power (and gas, if applicable) before starting any repair
• Remove the door or access panel to reach the latch per your model's service instructions
• Compare the new latch to the old part for correct orientation before installation
• Test the door operation after installation to ensure secure engagement

This pivot screw secures a hinge, lever, or linkage to its bracket to create a stable pivot point. Replacing a missing or stripped screw restores proper alignment and smooth movement of the assembly.

• Fastens a pivoting component to its mounting point
• Maintains alignment and smooth, controlled motion at the pivot
• Helps prevent looseness, wobble, or sag at the joint
• Common symptoms include a missing/loose screw, binding movement, rattling, or uneven gaps

• Disconnect power; shut off gas/water if applicable before servicing
• Support the hinged or moving component to remove load from the pivot
• Remove the damaged screw and start the new screw by hand to avoid cross-threading
• Tighten snugly without over-torquing; replace companion bushings or washers if worn

This wavy spring washer applies light, consistent preload between mating parts so components stay snug and quiet. It helps control end play and vibration, supporting smoother, more reliable operation of the assembly.

• Applies axial spring tension to take up end play between parts on a shaft or fastener
• Helps resist loosening from vibration and keeps components fitting tightly
• Can address wobble, rattling, or uneven spacing when the original washer is worn or missing
• Maintains proper alignment and feel in the assembly

• Disconnect power and shut off gas/water before servicing; allow hot surfaces to cool
• Note the original stack order and position before removal; replace in the same orientation
• Seat the washer evenly and avoid over-compressing during reassembly
• Verify smooth operation and minimal play after installation

Two pack Lid Covers used with 4.5 and 5 Quart KitchenAid Tilt Head Stand Mixer. The covers are used for variety of situations for example, when you need to keep ingredients in the bowl cold for hours or want to save extra cookie dough. The Lid Covers are dishwasher safe on the top-rack and fit KitchenAid Stand Mixer models K45SS, KSM75, KSM95, KSM150PS, KSM152PS and KSM155GB.

The 4.5 & 5 Quart KitchenAid Coated Flat Head Beater is an OEM part for Whirlpool KitchenAid stand mixers. This flat beater is designed for thorough mixing and blending of ingredients, ensuring consistent results for a variety of recipes.

Over time, the coated flat head beater can become worn or damaged due to regular use or accidental impact. Coating wear, bending, or chipping can compromise its effectiveness and lead to less efficient mixing.

Symptoms of a bad flat head beater include:

• Chipped or peeling coating
• Bending or warping of the beater
• Inefficient or inconsistent mixing
• Noise or scraping during use

This OEM part is also compatible with Maytag, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

4.5 Quart Polished Stainless Steel Mixing Bowl with Handle for Tilt Head mixers, has enough capacity to mix dough for 6 dozen cookies, 3 loaves of bread or 6 pounds of mashed potatoes in a single batch. Dishwasher-safe for quick and easy cleanup The Stainless Steel Mixing Bowl fits Kitchenaid Stand Mixer models K45SS, KSM75 and KSM95.

The 4.5 & 5 Quart KitchenAid Dough Hook is an OEM replacement part for  KitchenAid stand mixers. As part of the power knead attachment collection, this dough hook gently kneads and incorporates ingredients when making breads, rolls, pizza dough, and more. 

The curved blades of the hook provide thorough mixing and stretching of gluten strands for developing elasticity in yeasted doughs. Its integrated planetary motion helps eliminate sticking while providing a professional-quality knead. 

Symptoms of a bad dough hook include: 

• Vibration or grinding noises during use
• Inability to properly incorporate or knead ingredients  
• Dough sticking excessively to hook blades
• Visible damage, cracks, or bends in hook tines or housing

The coated Dough Hook fits KitchenAid Stand Mixer models K45SS, KSM75, KSM95, KSM150PS, KSM152PS and KSM155GB. 

This Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

The K45WW 4.5 & 5 Quart Wire Whip is an OEM part for KitchenAid mixers, specifically designed to fit Whirlpool models. This wire whip is used for incorporating air into ingredients, making it ideal for whipping egg whites, cream, and creating fluffy mixtures for recipes.

You should replace this wire whip if it becomes damaged or worn out. Causes of a bad wire whip can include bending or breaking of the wires due to overuse, exposure to heavy or dense mixtures, or corrosion from prolonged exposure to moisture.

Symptoms of a bad wire whip include:

• Inadequate mixing or whipping
• Bent or broken wires
• Poorly aerated mixtures
• Increased mixing time

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Pouring Shield is an OEM part for KitchenAid mixers. This part fits snugly onto the mixing bowl, helping to prevent ingredients from splattering out during mixing. It also features a convenient pour spout that allows for easy addition of ingredients without stopping the mixer.

Causes of a bad pouring shield can include accidental drops or impacts, exposure to high heat, or stress from frequent use.

Symptoms of a bad pouring shield include:

• Difficulty fitting the shield onto the mixing bowl
• Cracks or chips in the plastic
• Ingredients splattering out during mixing
• Difficulty adding ingredients through the pour spout

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.