Parts for Electrolux CGEF302TPFA: 03 - Body Parts

A small replacement clip that secures trim, panels, or wiring in place to restore a snug fit and reduce rattles. Use this direct-fit clip when the original is cracked, broken, or no longer holds components securely. What it does

• Secures panels, trim pieces, or small assemblies to prevent movement and vibration.
• Holds wiring harnesses or tubes in position to reduce rubbing and wear.
• Restores proper alignment of fitted parts that have come loose.
• Commonly replaces brittle or broken plastic clips that cause rattling or gaps.

• Disconnect power to the appliance before attempting any service.
• Remove surrounding trim or panels carefully to avoid damage to adjacent parts.
• Install the clip by aligning it with the mating slot or hole and pressing until it snaps into place.
• If the mating feature is damaged, replace or repair that surface to ensure a secure fit.

This machine screw adjusts and secures the leveling leg or bracket, helping you set the appliance stable and plumb. Replacing a stripped, bent, or missing screw restores a solid footing and makes accurate leveling possible.

• Threads into the base or leveling bracket to raise or lower the appliance for proper leveling
• Helps reduce rocking, wobbling, and vibration from an unlevel installation
• Common signs of wear: stripped threads, bent hardware, corrosion, or a missing screw
• Useful during installation or when the existing adjustment screw no longer holds

• Disconnect power; shut off gas before working
• Support the appliance to relieve weight on the leveling point
• Remove the damaged screw; inspect and clean mating threads
• Start the new screw by hand to avoid cross-threading, then adjust height and snug

This replacement shield protects nearby components from heat and debris, helping the appliance run safely and reliably. It restores the original barrier that prevents heat transfer to wiring and adjacent parts. What it does:

• Shields adjacent components from heat and direct exposure to the heating source
• Helps prevent heat-related damage to wiring, sensors and plastic parts
• Reduces risk of overheating hotspots that can cause premature part failure
• Can resolve issues where visible warping, cracks or burn marks are present

• One replacement shield as shown

• Turn off power and unplug the appliance before inspecting or replacing this part
• Handle with care — sharp edges may be present; use gloves and eye protection
• Follow the appliance service manual for mounting orientation and fastener torque
• If other components show heat damage, inspect and replace those parts as needed

This broiler insert is the oven pan insert that sits under the broiler burner to catch drips and help direct heat for even browning. It restores a stable cooking surface and keeps the broiler area cleaner. What it does:

• Holds food and catches grease and drips during broiling to prevent mess and flare-ups
• Directs heat from the broiler for consistent browning and searing
• Replaces damaged, warped, or corroded inserts that cause uneven cooking
• Helps prevent food from falling into the burner area

• One broiler insert

• Disconnect power to the appliance and allow the oven to cool completely before servicing
• Remove oven racks and slide the old insert out; position the new insert so it seats securely in the broiler cavity
• Wear heat-resistant gloves when testing the broiler after installation and inspect for proper fit before use
• Do not modify the part; use only as designed for the oven broiler assembly

This flexible replacement door gasket creates a tight seal to help keep cold in and moisture out, restoring proper temperature control and preventing leaks or frost buildup. Designed to match the OEM shape and fit. What it does:

• Seals the appliance door to help maintain internal temperature and energy efficiency
• Prevents water leaks and reduces frost or ice buildup in freezer compartments
• Helps the door close securely and evenly to avoid cold-air loss
• Common symptom fix: resolves visible tears, gaps, or warped gasket edges that allow air to pass

• One replacement door gasket/seal

• Disconnect power and empty the compartment before replacing the gasket
• Clean and dry the door frame surface thoroughly for a proper seal
• Work the gasket into the channel evenly; avoid stretching or twisting the material
• If adhesive or clips are present, use only OEM-recommended hardware or procedures

Restore dependable oven-light operation. This door-activated switch turns the oven's interior light on when the door opens and off when it closes, letting you check food at a glance and preventing the light from staying on unnecessarily. What it does:

• Detects door position to control the oven cavity light on/off
• Worn or stuck contacts can make the light stay on with the door closed
• Failed switch can prevent the light from turning on when the door opens
• Intermittent or flickering light may indicate a failing switch

• 1 switch

• Disconnect power to the appliance before servicing
• Access the switch (typically mounted in the front frame near the door opening)
• Move wires to the new switch one at a time to maintain correct placement
• Reinstall, then test door/light operation before final reassembly

This small replacement spacer positions and secures appliance components to maintain correct alignment and fit. Installing the spacer restores proper panel spacing and reduces vibration where a worn or missing spacer causes looseness or rubbing. What it does:

• Maintains the correct gap between panels, trim, or assemblies to ensure parts fit flush
• Keeps components aligned to prevent rubbing, binding, or uneven wear
• Helps reduce vibration and rattling caused by a missing or damaged spacer
• Preserves original part spacing for reliable operation of the surrounding components

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove any trim or fasteners that block access; keep track of screws and small parts
• Match the new spacer's orientation to the original; do not force parts into place

The Temperature Sensor is an OEM part for Frigidaire ovens. It monitors and helps regulate the oven's internal temperature, ensuring consistent cooking results by accurately detecting temperature changes. This sensor is crucial for the oven's control system to maintain the desired cooking temperature.

Symptoms of a bad Temperature Sensor include:

• Inaccurate oven temperature readings,
• Oven not heating to the set temperature,
• Oven overheating,
• Frequent temperature fluctuations during use.

Causes of a sensor failure can include prolonged exposure to high temperatures, electrical surges, or a breakdown of the sensor's components due to normal wear and tear.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This is a replacement 3-prong power cord for your appliance that restores safe, reliable power connection and replaces a damaged or worn cord. It helps ensure the unit can be powered without intermittent outages or exposed wiring. What it does

• Provides the main AC connection between the appliance and household power outlet
• Replaces frayed, cut, or damaged cord causing intermittent power or no power
• Restores a secure earth/ground connection via the third prong when applicable
• Helps prevent shocks and electrical arcing from damaged insulation or connectors

• Always disconnect power at the breaker or unplug the appliance before replacing the cord
• Confirm terminal type and routing before installation; secure with any existing strain relief or clamp
• If terminals or connector housings differ, do not force

The Terminal Block Kit is an OEM part for Frigidaire appliances, typically used for connecting house power to various electrical appliances like ranges and dryers. This kit includes includes screws, nuts, and a unique terminal block. It plays a critical role in the power supply system by providing a reliable connection point for the appliance's main power cord, preventing loose connections and potential electrical hazards.

Symptoms of a bad Terminal Block Kit include:

• Signs of burning or melting at the connection points,
• Flickering power or intermittent operation of the appliance,
• A burning smell from the appliance area.

Causes of terminal block failure often involve loose connections that can lead to arcing and overheating, improper installation, or general wear and tear that degrades the integrity of the electrical contacts.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Broil Heating Element is an OEM part for Frigidaire ranges. Located inside the oven compartment, it provides heat energy for the broil cooking function. 

Causes of a bad broil element can include mineral buildup over time, surface corrosion or internal wire fatigue from ongoing temperature cycling.

Symptoms of a bad broil element include:

• Inadequate or uneven broiling temperatures
• Element failing to glow red or turn on fully
• Burning or charring of foods below the element
• Oven display showing error code related to element failure

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This oven heating element replaces the failed bake element to restore even cooking heat in electric ovens. It delivers reliable surface heating where the original element no longer reaches or maintains set temperatures. What it does:

• Heats the oven cavity during bake cycles so food cooks and browns properly.
• Commonly used when the oven takes too long to heat or won't reach temperature.
• Can help correct uneven baking or cold spots caused by a broken element.
• Works as a direct replacement for a damaged, visibly burned, or open-circuit bake element.

• One oven bake heating element.

• Disconnect power to the appliance at the breaker before starting work.
• Handle carefully; heating elements are fragile and can be damaged by rough handling or bending.
• Verify proper fit and terminal connections match the original element before securing.

The Thermal Fuse is an OEM part for Frigidaire ovens and ranges. It acts as a safety device that cuts off power to the appliance if it overheats, preventing potential damage or fire hazards. This fuse ensures that the oven operates within safe temperature limits by shutting down the electrical circuit when necessary.

Causes of a bad thermal fuse can include prolonged exposure to high temperatures, electrical surges, or a malfunctioning oven component that causes overheating. These issues can compromise the integrity of the fuse, rendering it ineffective.

Symptoms of a bad thermal fuse include:

• The oven not heating up
• The oven shutting off unexpectedly during use
• No power to the oven

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This hex flange nut secures components where a broader bearing surface is needed to resist loosening and distribute load. It fits 10-32 threaded studs and is used on fastened assemblies in appliances. What it does:

• Provides a secure threaded connection for 10-32 screws and studs
• Flange spreads clamping force to reduce panel or bracket damage
• Hex shape allows tightening with a wrench for a reliable hold
• Commonly replaces worn or missing nuts that cause loose panels or rattling

• One hex flange nut

• Use the correct 10-32 screw or stud and hand-start threads to avoid cross-threading
• Tighten with an appropriately sized wrench; do not overtighten to prevent thread or part damage
• Disconnect power and follow appliance safety instructions before servicing
• Replace only like-for-like; confirm size and thread match your application

This ceramic catalyst oven vent fits behind the oven broiler to help vent and break down cooking residues and odors at high temperatures, keeping oven air cleaner during cooking and self-clean cycles. It's a direct-replacement part when the original is cracked, clogged, or missing. What it does:

• Provides a heat-resistant vent surface that helps oxidize grease and odors that pass through the vent during use
• Helps maintain proper oven ventilation for consistent cooking and cleaner internal airflow
• Commonly replaced when the vent is cracked, glazed-over, excessively discolored, or emits persistent odors
• Works as part of the oven's venting system—does not affect electronic controls

• Disconnect power to the appliance before starting any work to avoid shock or injury
• Allow the oven to cool fully; this part is installed inside the oven cavity or broiler area and may require removing racks or access panels
• Handle with care—ceramic components can crack if dropped or flexed; wear gloves to protect hands and avoid fingerprints on ceramic surfaces

This is a replacement mounting screw used to secure the appliance power/control board, restoring a solid electrical board connection and preventing vibration or loose contacts. Ideal for repairs where the original screw is missing or damaged. What it does:

• Fastens the power/control board to the appliance chassis to keep connections stable
• Helps prevent board movement that can cause intermittent electrical issues or noise
• Restores proper mounting after service or component replacement

• Turn off and unplug the appliance before starting any repair
• Use appropriate screwdriver and avoid over-tightening to prevent board or thread damage
• Wear eye protection and keep small parts away from children and pets

This harness assembly routes power and signals between components for safe, reliable appliance operation. It replaces a damaged or worn wiring harness to restore electrical connections and reduce intermittent faults. What it does:

• Connects electrical components and sensors to the appliance control system
• Restores missing or intermittent power to downstream parts
• Helps prevent shorts from frayed or broken wires
• Maintains factory routing and connector fit for proper function

• Disconnect power to the appliance before attempting replacement
• Match connectors and routing to the original harness; do not force connectors
• Inspect surrounding insulation and clips; replace any damaged mounting hardware

This factory screw secures components in your appliance, restoring a tight, rattle-free fit. Replace missing or damaged hardware to keep panels, brackets, and trim properly fastened and aligned for safe, reliable operation.

• Secures panels, brackets, trim, or internal components to the chassis
• Replaces lost, rusty, stripped, or cross-threaded screws
• Helps eliminate looseness, gaps, and vibration/rattling
• Common signs: loose/misaligned panels or trim, rattling noises, missing or rounded screw heads

• Disconnect power (and shut off gas if applicable); allow the unit to cool completely
• Match to the original location and replace one at a time to maintain alignment
• Hand-start to prevent cross-threading; tighten snugly—do not overtighten
• Use light torque when threading into plastic or thin sheet metal

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts

This oven light bulb illuminates the interior of your range or wall oven. Replace a burned-out bulb to restore clear visibility while cooking, checking doneness through the window, and cleaning.

• Provides interior illumination when the oven light is activated
• Common fix for no oven light, dim or flickering light, or a failed bulb
• Helps you monitor food without opening the door

• Disconnect power at the breaker or unplug the appliance before servicing
• Allow the oven to cool completely to avoid burns
• Remove the lens/cover if present; replace the bulb per your model's socket; do not overtighten
• Restore power and test; if the light still doesn't work, inspect the socket and switch

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.