Parts for Electrolux CGES3065PFD: 03 - Body Parts

This machine screw adjusts and secures the leveling leg or bracket, helping you set the appliance stable and plumb. Replacing a stripped, bent, or missing screw restores a solid footing and makes accurate leveling possible.

• Threads into the base or leveling bracket to raise or lower the appliance for proper leveling
• Helps reduce rocking, wobbling, and vibration from an unlevel installation
• Common signs of wear: stripped threads, bent hardware, corrosion, or a missing screw
• Useful during installation or when the existing adjustment screw no longer holds

• Disconnect power; shut off gas before working
• Support the appliance to relieve weight on the leveling point
• Remove the damaged screw; inspect and clean mating threads
• Start the new screw by hand to avoid cross-threading, then adjust height and snug

This replacement oven rack restores a stable cooking surface for baking or roasting, letting cookware sit level for even heating and safe handling. Fits compatible Frigidaire ovens and ranges. What it does:

• Supports pots, pans and bakeware while cooking
• Restores proper clearance and airflow for even cooking
• Replaces warped, rusted or missing racks that cause cookware instability
• Allows safe insertion and removal of hot dishes when used with oven mitts

• Install by sliding rack into the oven rack guides until fully seated; no tools typically required
• Allow oven to cool completely before removing or installing the rack
• Inspect rack guides and clips for damage; replace guides if the rack does not seat securely
• Use oven mitts or gloves when handling hot racks; follow oven manufacturer's safety instructions

The Rack is an OEM part for Frigidaire ranges. It provides a sturdy surface for placing cookware and baking sheets, allowing for even cooking and optimal heat circulation within the oven. 

Causes of a bad rack can include prolonged exposure to high temperatures, heavy loads causing the rack to bend or warp, and normal wear and tear from frequent use.

Symptoms of a bad Rack include:

• Warping or bending of the rack, making it difficult to place items levelly
• Rust or corrosion, which can affect the cleanliness and safety of the cooking surface
• The rack not fitting properly within the oven, leading to instability or difficulty in sliding the rack in and out

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This broiler insert is the oven pan insert that sits under the broiler burner to catch drips and help direct heat for even browning. It restores a stable cooking surface and keeps the broiler area cleaner. What it does:

• Holds food and catches grease and drips during broiling to prevent mess and flare-ups
• Directs heat from the broiler for consistent browning and searing
• Replaces damaged, warped, or corroded inserts that cause uneven cooking
• Helps prevent food from falling into the burner area

• One broiler insert

• Disconnect power to the appliance and allow the oven to cool completely before servicing
• Remove oven racks and slide the old insert out; position the new insert so it seats securely in the broiler cavity
• Wear heat-resistant gloves when testing the broiler after installation and inspect for proper fit before use
• Do not modify the part; use only as designed for the oven broiler assembly

This refrigerator door gasket replaces a worn or damaged outer door seal to help maintain an airtight closure and improve cooling efficiency. It restores a proper seal to reduce drafts, moisture buildup and energy loss. What it does:

• Seals the refrigerator door to keep cold air in and warm air out
• Helps prevent frost buildup and water accumulation on the cabinet floor
• Reduces compressor run time by maintaining consistent internal temperature
• Common symptom: visible cracks, tears, or areas that no longer seat against the cabinet
• Common symptom: warm spots at the door edge or excess condensation

• One refrigerator door gasket

• Disconnect power to the appliance before beginning any work
• Remove the old gasket by loosening retainer screws or pulling out the retainer, then press the new gasket into the retainer channel, working around the perimeter
• For tight fits, gently warm the gasket (low heat) to make it more pliable—do not overheat or use open flame
• Inspect the seal for even seating and, if applicable, torque retainer screws to manufacturer spec

This replacement switch restores reliable control of a selected function by opening or closing an electrical circuit inside your appliance. When the original switch wears out, buttons may stop responding or features may not activate consistently.

• Opens/closes an electrical circuit when the button/actuator is engaged
• Routes power or sends a signal to the control or component
• Common symptoms: no response when pressed, intermittent operation, or function won't start
• May show signs of heat damage, loose terminals, or inconsistent "click" feel

• Disconnect power at the breaker before servicing
• Photograph or label wire positions to ensure correct transfer to the new switch
• Move wires one at a time; fully seat connectors on the correct terminals
• Reassemble, restore power, and test the function activated by the switch

The Range Lamp Assembly is an OEM part for Frigidaire stoves and ranges. It consists of the halogen light bulb, lens cover, and wiring harness necessary to illuminate the oven cavity. This lamp assembly provides light to the cooking and baking space, making it easier to view food and monitor cooking progress.  

Symptoms of a bad range lamp assembly include:

• The oven light not turning on at all  
• Dim, flickering, or intermittent light
• Burned out or blown light bulb
• Cracks or damage to the lens cover

Causes of failure can be a burned out light bulb, broken wiring, or damage from impact or heat over time. 

This OEM Frigidaire replacement part is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This small replacement spacer positions and secures appliance components to maintain correct alignment and fit. Installing the spacer restores proper panel spacing and reduces vibration where a worn or missing spacer causes looseness or rubbing. What it does:

• Maintains the correct gap between panels, trim, or assemblies to ensure parts fit flush
• Keeps components aligned to prevent rubbing, binding, or uneven wear
• Helps reduce vibration and rattling caused by a missing or damaged spacer
• Preserves original part spacing for reliable operation of the surrounding components

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove any trim or fasteners that block access; keep track of screws and small parts
• Match the new spacer's orientation to the original; do not force parts into place

The Temperature Sensor is an OEM part for Frigidaire ovens. It monitors and helps regulate the oven's internal temperature, ensuring consistent cooking results by accurately detecting temperature changes. This sensor is crucial for the oven's control system to maintain the desired cooking temperature.

Symptoms of a bad Temperature Sensor include:

• Inaccurate oven temperature readings,
• Oven not heating to the set temperature,
• Oven overheating,
• Frequent temperature fluctuations during use.

Causes of a sensor failure can include prolonged exposure to high temperatures, electrical surges, or a breakdown of the sensor's components due to normal wear and tear.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Oven Meat Probe is an OEM replacement part for Frigidaire ovens and ranges. It is used to accurately monitor the internal temperature of meat and other food items as they cook inside the oven.

Causes of a bad oven meat probe include damage to the temperature sensor or wiring over time from repeated high heat exposure during cooking. The wiring can fatigue and become brittle or the connector can corrode from steam and debris inside the hot oven area.

Symptoms of a bad oven meat probe include:

• Temperature readings that do not correspond to the food's actual doneness
• Inaccurate or inconsistent readings on the controller display
• The controller does not recognize that the probe is connected
• Physically damaged probe components like a cracked sensor tip

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore ranges.

This outer housing cover replaces a damaged or missing trim piece to protect internal components and restore the appliance's finished appearance. It fits as the exterior cover piece found on the original unit. What it does:

• Protects internal components from dirt, spills and accidental contact
• Conceals wiring and mounting points for a clean, finished look
• Prevents small items from entering sensitive areas that could cause faults
• Restores appearance after panel damage or wear

• One outer housing cover

• Disconnect power to the appliance before starting any service
• Follow the manufacturer's service instructions and keep track of fasteners
• Use basic hand tools; avoid flexing the part to prevent cracking

The Terminal Block Kit is an OEM part for Frigidaire appliances, typically used for connecting house power to various electrical appliances like ranges and dryers. This kit includes includes screws, nuts, and a unique terminal block. It plays a critical role in the power supply system by providing a reliable connection point for the appliance's main power cord, preventing loose connections and potential electrical hazards.

Symptoms of a bad Terminal Block Kit include:

• Signs of burning or melting at the connection points,
• Flickering power or intermittent operation of the appliance,
• A burning smell from the appliance area.

Causes of terminal block failure often involve loose connections that can lead to arcing and overheating, improper installation, or general wear and tear that degrades the integrity of the electrical contacts.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The Broil Heating Element is an OEM part for Frigidaire ranges. Located inside the oven compartment, it provides heat energy for the broil cooking function. 

Causes of a bad broil element can include mineral buildup over time, surface corrosion or internal wire fatigue from ongoing temperature cycling.

Symptoms of a bad broil element include:

• Inadequate or uneven broiling temperatures
• Element failing to glow red or turn on fully
• Burning or charring of foods below the element
• Oven display showing error code related to element failure

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This radiant cooktop surface element replaces a damaged or non-heating burner to restore even heating for stovetop cooking. Designed to fit compatible Frigidaire electric ranges and drop-in glass cooktops. What it does

• Heats cookware on an electric glass-top or coil-style cooktop so pots and pans reach cooking temperature.
• Replaces elements that show no heat, uneven heating, or visible damage.
• Works with the range's burner control to provide consistent temperature response.
• Commonly used when a burner fails to warm or cycles irregularly during use.

• Disconnect power to the range at the breaker before starting any work.
• Handle the glass cooktop and element terminals carefully to avoid cracking or damage.
• Verify correct element seating and secure electrical connections; do not bend terminals.

A direct-replacement motor that restores airflow in your appliance so fans and blowers run properly. Replacing a worn or failed motor helps maintain cooling and heating performance and reduces unusual noises or airflow loss. What it does

• Drives the fan or blower to circulate air through the appliance
• Restores proper airflow for temperature control and evaporator/condenser operation
• Stops or reduces noisy, inconsistent, or non-spinning fan symptoms
• Helps prevent overheating by ensuring adequate ventilation

• One motor

• Disconnect power before starting any repair to avoid shock
• Handle the motor and shaft carefully to avoid damage; support the assembly during removal and installation
• Use appropriate tools and follow the appliance service manual for mounting, wiring, and alignment

This control panel is the front console fascia that houses the oven/range controls and display, restoring the unit's user interface and appearance. It replaces a cracked, faded, or damaged console face to make controls accessible and look like new. What it does:

• Provides the visible bezel and button/display surface for the unit's electronic controls
• Restores a secure mounting surface for control buttons, knobs, and display elements
• Helps resolve issues with broken, cracked, or cosmetically damaged console areas
• Supports proper alignment of control electronics

• Disconnect power to the appliance before starting any repair to avoid electric shock
• Basic disassembly (removing trim screws and console fasteners) is typically required; keep hardware for reassembly
• Handle carefully to avoid scratching or cracking the new panel during install
• If control electronics or trim pieces are damaged, verify those parts separately; this panel is the fascia only

This electronic oven control board manages oven temperature, bake/broil functions, and the display/keypad. Replacing a failed board restores proper heating and responsive controls so the oven operates and times as it should. What it does:

• Regulates power to the bake/broil elements or gas valve to reach and maintain set temperature
• Interprets keypad inputs and controls oven modes (Bake, Broil, Start/Stop, Timer)
• Drives the digital display for time, temperature, and status
• Common symptoms of failure: no display, unresponsive buttons, oven won't heat or overheats, or recurring error beeps/codes

• 1 electronic control board assembly

• Disconnect power at the breaker; turn off gas supply for gas ranges
• Use ESD precautions; handle the board by its edges
• Label and transfer wire connectors one at a time; move any mounting hardware/overlay from the original, if required
• After installation, restore power, set the clock, and test oven modes

This is a replacement mounting screw used to secure the appliance power/control board, restoring a solid electrical board connection and preventing vibration or loose contacts. Ideal for repairs where the original screw is missing or damaged. What it does:

• Fastens the power/control board to the appliance chassis to keep connections stable
• Helps prevent board movement that can cause intermittent electrical issues or noise
• Restores proper mounting after service or component replacement

• Turn off and unplug the appliance before starting any repair
• Use appropriate screwdriver and avoid over-tightening to prevent board or thread damage
• Wear eye protection and keep small parts away from children and pets

This replacement motor drives the oven's fan to circulate air through the cavity, helping maintain even heat distribution. A weak or failed motor can cause the fan to stop or run noisily, affecting cooking performance. What it does:

• Powers the oven fan to move air through the cavity for consistent temperatures
• Helps support even baking and roasting results
• Common symptoms include the fan not spinning, intermittent operation, or loud humming/squealing from the rear of the oven
• Helps resolve poor convection performance when the fan is not turning

• 1 motor

• Disconnect power at the breaker before servicing
• Access may require removing the oven from the cabinet and the rear cover; follow your model's service procedure
• Transfer the existing fan blade and any mounting hardware from the old motor if required
• After installation, spin the fan by hand to ensure it turns freely and doesn't rub before restoring power

This replacement fan blade mounts to the appliance's fan motor to move air as designed. Installing a new blade restores proper airflow and helps reduce vibration or noise caused by bent, cracked, or worn fins. What it does

• Attaches to the fan motor shaft to move air through the cavity or across internal components
• Supports even air circulation or cooling performance, depending on model
• Helps resolve issues such as loud scraping/whirring, vibration/wobble, weak airflow, or visible blade damage

• One fan blade

• Disconnect power at the breaker and allow the appliance to cool completely before servicing
• Access the fan assembly from the rear panel or inside the oven behind the fan cover (varies by model); wear gloves—edges can be sharp
• Note blade orientation/rotation and securely reinstall using the original fastener(s)
• Hand-spin the blade to ensure clearance and free movement before reassembly and testing

This is a nut that is used in many microwave ovens. It is typically used to hold interior fan in place. A nut is a fastener that is used to hold two items together or keep one component secure against a surface. Use and time can cause the nut to become stripped, damaged, or broken. If the nut is broken, it will no longer hold the fan in the right location. The nut will need to be replaced.Before replacing this part, the microwave should be unplugged. Open the refrigerator door and remove the cover that goes over the fan. The nut can then be removed using a nut driver. Replace the other parts before using the appliance.This nut is used in microwave ovens manufactured by Crosley, Electrolux, Frigidaire, and Kenmore. It is sold as a single part. This is an authentic OEM replacement part is sourced directly from the manufacturer.

The Thermostat is an OEM component specifically designed for Frigidaire gas stoves. This thermostat controls burner temperatures by regulating gas flow. 

Causes of a bad thermostat include wear and tear over time, overheating, moisture damage, or power surges that can degrade electrical components.

Symptoms of a bad thermostat include:

• Inability to control burner temperatures accurately 
• Burners heating to excessively high or low levels
• Fluctuating burner output unrelated to dial settings
• Complete failure of one or more burners to light

Replace it today with this OEM Frigidaire part to maintain safe and reliable stove operation. This thermostat replacement is also compatible with Gibson and Kelvinator gas ranges, as well as select Kenmore models. 

The Convection Fan Motor is an OEM part for Frigidaire wall ovens and ranges. This electric motor is responsible for powering the convection fan located in the oven.

The convection fan circulates heated air around food during the cooking process, helping to cook foods more quickly and evenly without having to open the oven door.

Symptoms of a bad convection fan motor include:

• Loud grinding or humming noises coming from the oven cavity
• Reduced or no airflow from the convection fan/system
• Longer than normal cook times, even cooking issues

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This Tube Assembly routes water inside the refrigerator to the dispenser and ice-maker, restoring proper water flow and preventing leaks when the original line is damaged. Reliable replacement for delivery and fill connections. What it does:

• Transports water from the inlet to the ice maker/dispenser assembly
• Replaces cracked, kinked, or leaking tubing that causes puddles or low water flow
• Helps restore normal ice production and dispenser operation when the tube is the fault
• Matches OEM routing and connector types for correct fit and seal

• One tube assembly as shown

• Disconnect power and shut off the water supply before starting
• Remove ice maker or access panel as needed to reach routing; follow OEM service instructions
• Inspect fittings and replace any damaged clamps or seals; avoid kinking the new tube
• After installation, turn on water, check for leaks, and run dispenser/ice cycles to confirm proper flow

This mounting bracket secures internal components to the appliance cabinet, restoring proper alignment and stable support where factory brackets have broken or come loose. A direct-fit replacement that helps stop shifting, rattles, and misalignment. What it does:

• Provides a secure mounting point for panels, assemblies, or components inside the cabinet
• Restores correct alignment when a damaged bracket allows parts to sag or move
• Reduces vibration and rattling caused by loose or missing support
• Helps maintain proper clearances for doors and internal assemblies

• One replacement mounting bracket

• Disconnect power to the appliance before starting any repair
• Remove any obstructing panels, shelves, or components to access the bracket
• Keep original fasteners; replace only if explicitly specified by OEM instructions

Replacement water-line tube that routes water inside the refrigerator to the ice maker or dispenser, helping restore proper water flow and reduce leaks. Designed to match factory routing so the line fits and seals correctly at the connections. What it does:

• Carries water from the cabinet valve to the ice maker or dispenser.
• Restores normal dispenser flow and ice production when the tube is cracked, pinched, or clogged.
• Helps stop visible leaks or pooling caused by damaged or misrouted tubing.
• Matches factory bends for correct routing and clearance behind panels.

• Disconnect power and shut off the water supply before starting any work.
• Remove shelves or panels as needed for access; watch for sharp edges.
• Check and replace any worn clamps or fittings; tighten connections and test for leaks with water on before reassembling.

This harness assembly routes power and signals between components for safe, reliable appliance operation. It replaces a damaged or worn wiring harness to restore electrical connections and reduce intermittent faults. What it does:

• Connects electrical components and sensors to the appliance control system
• Restores missing or intermittent power to downstream parts
• Helps prevent shorts from frayed or broken wires
• Maintains factory routing and connector fit for proper function

• Disconnect power to the appliance before attempting replacement
• Match connectors and routing to the original harness; do not force connectors
• Inspect surrounding insulation and clips; replace any damaged mounting hardware

This mounting bracket secures internal panels or components to the appliance frame, restoring stable support and alignment for proper operation. Use when a bracket is bent, broken or missing to reduce rattling and keep parts positioned correctly. What it does:

• Anchors panels or components to the cabinet/frame to prevent movement and vibration
• Restores proper alignment of doors, panels or internal assemblies
• Stops rattling or buzzing caused by loose or damaged support hardware
• Helps maintain safe clearance between parts and wiring or moving components

• Disconnect power to the appliance before starting any repair
• Basic hand tools typically required; follow OEM instructions for correct fastener locations
• Inspect adjacent fasteners and mounting surfaces; replace any damaged screws or clips
• If bracket is corroded or severely deformed, replace rather than re-bend to ensure proper fit

This hex flange nut secures components where a broader bearing surface is needed to resist loosening and distribute load. It fits 10-32 threaded studs and is used on fastened assemblies in appliances. What it does:

• Provides a secure threaded connection for 10-32 screws and studs
• Flange spreads clamping force to reduce panel or bracket damage
• Hex shape allows tightening with a wrench for a reliable hold
• Commonly replaces worn or missing nuts that cause loose panels or rattling

• One hex flange nut

• Use the correct 10-32 screw or stud and hand-start threads to avoid cross-threading
• Tighten with an appropriately sized wrench; do not overtighten to prevent thread or part damage
• Disconnect power and follow appliance safety instructions before servicing
• Replace only like-for-like; confirm size and thread match your application

This factory screw secures components in your appliance, restoring a tight, rattle-free fit. Replace missing or damaged hardware to keep panels, brackets, and trim properly fastened and aligned for safe, reliable operation.

• Secures panels, brackets, trim, or internal components to the chassis
• Replaces lost, rusty, stripped, or cross-threaded screws
• Helps eliminate looseness, gaps, and vibration/rattling
• Common signs: loose/misaligned panels or trim, rattling noises, missing or rounded screw heads

• Disconnect power (and shut off gas if applicable); allow the unit to cool completely
• Match to the original location and replace one at a time to maintain alignment
• Hand-start to prevent cross-threading; tighten snugly—do not overtighten
• Use light torque when threading into plastic or thin sheet metal

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts

This replacement light bulb restores bright, dependable illumination inside your oven so you can monitor cooking without opening the door. Swap it in when the oven light is out, very dim, or flickers during use. What it does:

• Illuminates the oven cavity in a range or wall oven
• Lets you check food without opening the door and losing heat
• Common fix for no light, dim light, or intermittent flickering
• Replaces a burned-out/broken bulb as the first step in troubleshooting

• One light bulb

• Disconnect power at the breaker or unplug the appliance; allow the oven to cool completely.
• Remove the light cover/lens per your model; handle glass components carefully.
• Install the new bulb securely; avoid touching the glass with bare hands—use a clean cloth or gloves.
• Reinstall the cover, restore power, and test the oven light.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.

The Screw is an OEM part for Frigidaire ranges and ovens. This part is designed to securely fasten various parts of the appliance, ensuring stability and durability. 

Over time, screws can become loose due to the expansion and contraction of materials with temperature changes. Regular use and the occasional necessary removal for repairs or cleaning can also wear down the threads, making them less effective.  

Symptoms of a bad Screw (Chrome) include:

• Loose or wobbly components that should be securely fastened.
• Difficulty in securing parts due to stripped or damaged screw threads.
• Visible corrosion or deterioration of the screw.

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Size: 8-18 x 0.5 inch. Color: Chrome.