Parts for Electrolux E30GF74TPSB: Body Parts

Mounting screw for gas ranges. Secures internal components and panels. Replace if screw is stripped, missing, or damaged during appliance service.

This mounting bracket secures internal components and panels to restore proper alignment and stability. It's a simple replacement that helps stop loose panels, rattles, or misaligned parts so your appliance fits and operates correctly. What it does:

• Provides a secure mounting point for adjacent panels or assemblies
• Restores alignment to reduce vibration, noise, and rubbing
• Replaces damaged, bent, or broken brackets that cause gaps or loose parts
• Matches OEM fit to reinstall original components without modification

• Inspect surrounding fasteners and panels for damage before installing
• Use correct-size screws and tighten to snug — do not overtighten to avoid stripping
• Disconnect power and empty the area of work if access requires panel removal

Oven broiler pan catches drippings and supports food during broiling. Replace this pan if yours is warped, damaged, or missing for safe cooking and easier cleanup.

This broiler insert is the oven pan insert that sits under the broiler burner to catch drips and help direct heat for even browning. It restores a stable cooking surface and keeps the broiler area cleaner. What it does:

• Holds food and catches grease and drips during broiling to prevent mess and flare-ups
• Directs heat from the broiler for consistent browning and searing
• Replaces damaged, warped, or corroded inserts that cause uneven cooking
• Helps prevent food from falling into the burner area

• One broiler insert

• Disconnect power to the appliance and allow the oven to cool completely before servicing
• Remove oven racks and slide the old insert out; position the new insert so it seats securely in the broiler cavity
• Wear heat-resistant gloves when testing the broiler after installation and inspect for proper fit before use
• Do not modify the part; use only as designed for the oven broiler assembly

This refrigerator door gasket replaces a worn or damaged outer door seal to help maintain an airtight closure and improve cooling efficiency. It restores a proper seal to reduce drafts, moisture buildup and energy loss. What it does:

• Seals the refrigerator door to keep cold air in and warm air out
• Helps prevent frost buildup and water accumulation on the cabinet floor
• Reduces compressor run time by maintaining consistent internal temperature
• Common symptom: visible cracks, tears, or areas that no longer seat against the cabinet
• Common symptom: warm spots at the door edge or excess condensation

• One refrigerator door gasket

• Disconnect power to the appliance before beginning any work
• Remove the old gasket by loosening retainer screws or pulling out the retainer, then press the new gasket into the retainer channel, working around the perimeter
• For tight fits, gently warm the gasket (low heat) to make it more pliable—do not overheat or use open flame
• Inspect the seal for even seating and, if applicable, torque retainer screws to manufacturer spec

Oven not responding to buttons or features won't activate? This control switch restores reliable operation by opening and closing electrical circuits.

Replace a cracked, broken, or missing oven door spacer that maintains proper alignment and gap between door components. Installs in door assembly.

Oven won't reach or hold set temperature? A faulty temperature sensor causes inaccurate heating. This monitor probe ensures consistent cooking results.

Replacement power cord for ovens and ranges. Installs at the rear panel to restore electrical connection. Needed when original cord is frayed or damaged.

Secures the oven bottom panel in place. Replace if screw is stripped, missing, or no longer holds the panel securely. Sold individually.

This cabinet insulation panel helps reduce heat transfer into the refrigerator cabinet so the appliance maintains proper operating temperatures and runs more efficiently. Designed to replace a worn or missing insulation panel. What it does:

• Fills the cavity between the cabinet and liner to slow heat gain from room air
• Helps the refrigerator maintain set temperatures and reduces compressor run time
• Can prevent moisture buildup and frost issues caused by missing or damaged insulation
• Restores proper airflow paths when original insulation has shifted or deteriorated

• One insulation panel

• Disconnect power before servicing and remove any stored food from the area being worked on
• Access may require removing interior liners or panels; keep fasteners and trim for reinstallation
• Handle insulation carefully; avoid compressing or tearing the material during placement
• Wear gloves and a dust mask; follow local disposal regulations for removed material

This shield is a small protective panel that helps guard internal components from heat, debris and loose connections. It restores proper coverage and reduces the chance of contact or chafing that can lead to noise or component damage. What it does:

• Covers and protects wiring, terminals or sensitive components from direct heat and physical contact
• Helps prevent debris buildup and reduces rubbing or chafing against moving parts
• Can stop vibration-related noise when damaged or loose
• Restores the appliance's original safety barrier when the original shield is cracked, bent or missing

• Disconnect power before attempting any repair; work only with the appliance fully de-energized
• Inspect surrounding clips, screws and mounting tabs and replace any that are damaged
• Handle sharp edges carefully and secure shield firmly so it cannot contact terminals or moving parts

Heat shield for ranges and wall ovens. Protects internal components from excessive heat. Replace if cracked, warped, or damaged to prevent overheating.

Receptacle for electric and gas ranges and wall ovens. Installs as a connector component. Replace if cracked, damaged, or missing to restore proper fit.

If your oven isn't heating evenly or the convection fan isn't working, this motor restores proper airflow. Moderate difficulty repair in 30-45 minutes.

This replacement support is a small mounting bracket that secures internal components and stabilizes assemblies to reduce vibration and wear. It restores proper alignment for reliable operation and quieter performance. What it does:

• Holds and positions internal parts or panels to prevent shifting during use
• Reduces rattling, vibration, and misalignment-related noise
• Helps maintain proper spacing for moving components and hoses
• Supports stable operation after damage, cracks, or missing fasteners

• Disconnect power (and water if applicable) before starting any repair
• Inspect surrounding fasteners and mating surfaces; replace damaged screws or clips
• Requires basic hand tools; handle edges carefully to avoid cuts

Mounting screw for electric and gas ranges. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Fix loud rattling or grinding noise from your oven fan. This convection fan motor restores quiet operation and even heat distribution. DIY repair.

Loud grinding or rattling from your oven? A damaged convection fan blade disrupts airflow. This replacement restores quiet operation in 20-30 minutes.

This is a nut that is used in many microwave ovens. It is typically used to hold interior fan in place. A nut is a fastener that is used to hold two items together or keep one component secure against a surface. Use and time can cause the nut to become stripped, damaged, or broken. If the nut is broken, it will no longer hold the fan in the right location. The nut will need to be replaced.Before replacing this part, the microwave should be unplugged. Open the refrigerator door and remove the cover that goes over the fan. The nut can then be removed using a nut driver. Replace the other parts before using the appliance.This nut is used in microwave ovens manufactured by Crosley, Electrolux, Frigidaire, and Kenmore. It is sold as a single part. This is an authentic OEM replacement part is sourced directly from the manufacturer.

The Thermostat is an OEM component specifically designed for Frigidaire gas stoves. This thermostat controls burner temperatures by regulating gas flow. 

Causes of a bad thermostat include wear and tear over time, overheating, moisture damage, or power surges that can degrade electrical components.

Symptoms of a bad thermostat include:

• Inability to control burner temperatures accurately 
• Burners heating to excessively high or low levels
• Fluctuating burner output unrelated to dial settings
• Complete failure of one or more burners to light

Replace it today with this OEM Frigidaire part to maintain safe and reliable stove operation. This thermostat replacement is also compatible with Gibson and Kelvinator gas ranges, as well as select Kenmore models. 

Replacement mounting screw for range power and control boards. Secures electrical board connections. Needed when original screw is missing or damaged.

This evaporator fan motor circulates cold air across the evaporator coil to maintain even cooling and proper freezer/refrigerator temperatures. It replaces a worn or failed circulation motor to restore airflow and cooling performance. What it does:

• Spins the evaporator fan blade to move cold air through the compartment.
• Helps prevent temperature imbalances and warm spots.
• Can run quietly when operating correctly; a failing motor can cause noise or intermittent airflow.
• Common symptom: no airflow from vents, reduced cooling, or unusual humming/grinding noises during fan operation.

• One evaporator fan motor.

• Disconnect power to the appliance before starting any repair.
• Access typically requires removing interior panels or the freezer evaporator cover; follow your model's service manual.
• Handle the fan blade and connector carefully to avoid damage; ensure correct blade orientation and secure electrical connections.

Reinforces and supports oven door glass panels. Replace if original stiffener is bent, cracked, or missing to properly secure glass in the door frame.

This oven bake element replaces the heating element that warms the oven cavity so it reaches and maintains baking temperatures. Restores consistent heat for baking, roasting and broiling when the original element fails. What it does:

• Heats the oven cavity so cookware reaches set temperatures for even baking and roasting
• Commonly diagnosed when the oven won't heat or takes too long to reach temperature
• Can reduce hot spots and uneven cooking caused by a burned-out or damaged element
• Works with standard electric ovens that use a replaceable bake element

• Disconnect power to the oven at the breaker before starting any repair
• Handle the element and terminals carefully—sharp edges and fragile mount tabs are common
• Verify correct terminal connections and secure mounting for safe operation

Replace your worn or missing range spacer to restore proper component alignment and spacing. This small plastic part maintains correct clearances inside the unit.

This trim is a replacement decorative bezel that restores the finished edge and appearance of the appliance. It covers gaps and protects underlying components for a clean, factory look. What it does:

• Replaces cracked, dented, or missing decorative edge trim
• Hides gaps between panels for improved appearance
• Keeps moisture and debris away from seams and fasteners
• Helps trim stay flush and aligned with adjacent panels

• Disconnect power and/or water before starting work.
• Remove any damaged trim and clean mounting surface before installing new trim.
• Typically installs by aligning and snapping or fastening into place; use appropriate hand tools.
• Handle carefully to avoid scratching finish; do not overtighten fasteners.

Replacement water-line tube that routes water inside the refrigerator to the ice maker or dispenser, helping restore proper water flow and reduce leaks. Designed to match factory routing so the line fits and seals correctly at the connections. What it does:

• Carries water from the cabinet valve to the ice maker or dispenser.
• Restores normal dispenser flow and ice production when the tube is cracked, pinched, or clogged.
• Helps stop visible leaks or pooling caused by damaged or misrouted tubing.
• Matches factory bends for correct routing and clearance behind panels.

• Disconnect power and shut off the water supply before starting any work.
• Remove shelves or panels as needed for access; watch for sharp edges.
• Check and replace any worn clamps or fittings; tighten connections and test for leaks with water on before reassembling.

Secures internal panels or components to the range frame. Replace this mounting bracket if bent, broken, or missing to restore stable support and alignment.

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

Replacement mounting screw for ovens and ranges. Secures panels, brackets, trim, and internal components. Replace missing or stripped screws to restore fit.

Replacement screw secures panels, trim, and internal components in your appliance. Needed when original fastener is missing, stripped, or damaged.

Illuminates your oven interior for visibility while cooking and cleaning. Replace when burned out to restore lighting. Verify fit with your model number.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.