Bolens Tiller Parts

Fastening screw for outdoor power equipment. Secures components and reduces vibration. Replace if stripped, corroded, or missing from your machine.

Seals between carburetor and engine to prevent air leaks and maintain proper compression. Replace if damaged, cracked, or during carburetor rebuild. Verify fit with your model number.

This is a replacement pull rope for a small engine recoil starter assembly used on tillers, lawn mowers, and similar outdoor power equipment. The rope winds around the starter pulley and is pulled to crank the engine for starting. Replace this rope if it is frayed, broken, or no longer retracts properly into the starter housing.

This is a quality clevis pin that is made for many types of lawn and garden equipment. It secures two components together. A clevis pin has a hole at the end where a cotter pin can be attached to secure it in place. Clevis pins can become damaged or corroded over time, which will require them to be replaced.If a damaged clevis pin is difficult to remove, it can be sprayed with penetrating oil and allowed to sit for several hours. This should make it easier to remove the cotter pin from the clevis pin. If it doesn't budge, use a pry bar to loosen the clevis pin.This is an authentic OEM replacement clevis pin directly sourced from the manufacturer. It is sold as a single pin. The clevis pin is designed to be used with lawnmowers, tillers, and snowblowers manufactured by MasterCut, Yard-Man, Bolens, Montgomery Wards, Huskee, MTD, Yard Machines, Husky, Troy-Bilt, Ryobi, Cub Cadet, and Craftsman.

Secures moving parts and linkages on tractors and outdoor equipment. Replace if bent, broken, or missing to prevent parts from detaching during operation.

This extension spring attaches to the axle support bracket and the drive belt idler pulley on many types of lawn and garden equipment. It creates additional tension to the drive belt idler pulley. Sometimes the extension spring can be stretched out or may break, often caused through excess use. If this is the case, the spring will need to be replaced.If the spring is broken or no longer creates the appropriate amount of tension, replacement is required. It is an easy process that only requires a set of pliers. The pliers can be used to take the old spring off of the yard equipment before attaching the new extension spring. Make sure the equipment is on a stable surface and powered off when working with it. Remove the spark plug wire to prevent accidents.This extension spring is an authentic OEM replacement part sourced directly from the manufacturer. It is sold as an individual component. The spring is made to be used with lawnmowers, lawn tractors, and tillers created by MasterCut, Yard-Man, Bolens, Huskee, MTD, Yard Machines, Murray, Troy-Bilt, Cub Cadet, and Craftsman.

Flat washer for lawn mowers and outdoor power equipment. Replaces damaged, missing, or worn washers. Standard hardware component for various models.

Flange bearing for lawn tractors and walk-behind mowers. Replace when you notice excessive noise, wobbling, or difficulty with blade rotation. Verify fit with your model number before ordering.

Tiller won't engage or tines stop spinning? This clutch control cable connects your handle lever to the clutch mechanism. Moderate DIY repair.

This is a small engine spark plug positioned in the engine cylinder head. It supplies the spark that will ignite the air-fuel mixture to enable an engine to produce power. This particular spark plug is designed with superior corrosion resistance and dependable performance. Small but mighty, this component allows for increased conductivity and heat control. If the spark plug is damaged or in poor condition, many problems may arise in equipment, including sudden stop while running, overheating, and excessive gas consumption. Replace the spark plug by disconnecting the spark plug wire first, then use a socket driver or wrench to remove the spark plug. Install the new spark plug by turning it by hand initially to avoid cross-threading. If it doesn't twist anymore, use a deep socket wrench or socket driver to tighten the plug until snug. The spark plug can also be used to tune up outdoor power equipment or improve a small engine. This part is recommended to be replaced once per season. This part works with lawn mowers, snowblowers, tillers, leaf blowers, log splitters, wood chippers, and others with small engines. It is compatible with brands such as Craftsman, Cub Cadet, Troy-Bilt, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and MasterCut. This is a genuine OEM part directly from the manufacturer and is sold individually.

A fuel cap assembly is a component often seen on lawnmowers and other lawn and garden equipment. It is made of durable black plastic and is used to ensure that fuel doesn’t spill out of the fuel tank. Over time, fuel cap assemblies can begin to wear out and cause problems. Sometimes this results in a cap that doesn’t tighten all the way or there may be a fuel smell when using a lawnmower or snowblower. If fuel is leaking, the cap doesn’t fit right, or the cap seems damaged, it’s best to replace it with a new component. This is a simple process that involves removing the original fuel cap assembly and fitting the new assembly to the lawn machine. This fuel cap assembly is a genuine OEM component that comes directly from the manufacturer. It is an individual part that is compatible with MTD, Murray, Cub Cadet, Bolens, Yard-Man, and Yard Machines lawnmowers, snowblowers, chipper shredders, and tillers. No tools are required to replace this component.

Oil fill plug assembly for small engines. Seals the oil fill opening to prevent leaks. Replace if cracked, stripped, or missing to maintain proper seal.

Fuel filters are created to strain out gas before it reaches the carburetor in lawnmowers and other gardening tools. Located in the fuel line or the fuel tank, it prevents unwanted debris from reaching the carburetor, which can cause engine damage. If the fuel filter is damaged or becomes clogged with material, it no longer offers the same protection to the carburetor. This can lead to difficulty starting the lawnmower and decreased performance. Correcting this issue early can prevent damage that might require a new lawnmower. Maintenance of the lawnmower by adding fuel stabilizer, changing the oil, and replacing the air filter will increase the life of lawn care equioment. Even if no issues are present, the fuel filter should be replaced after about 200 hours of use. Disconnecting the spark plug should be done prior to installing a new fuel filter. This fuel filter is a genuine OEM component directly from the manufacturer and comes as an individual part. It can be used with various Craftsman, Cub Cadet, Murray, Yard Machines, MTD, Huskee, Bolens, Yard-Man, and Mastercut lawnmowers, tillers, blowers, and wood chippers.

Oil dipstick assembly for lawn and garden engines. Installs in the oil fill tube to measure current oil level. Replace if cracked, broken, or missing.