Bosch Clip Or Clamp

The Pump to Heater Hose Clamp is an OEM part for Bosch dishwashers. This clamp secures the hose that connects the pump to the heater, ensuring a tight and leak-free connection. It plays a crucial role in maintaining the integrity of the water flow within the dishwasher, preventing leaks and ensuring efficient operation.

Causes of a bad hose clamp can include wear and tear over time, loosening due to vibrations, or damage from repeated tightening and loosening. A faulty clamp can lead to water leaks, which can cause further damage to the dishwasher.

Symptoms of a bad pump to heater hose clamp include:

• Water leaking from the hose connection points
• Reduced water pressure within the dishwasher
• Visible wear, rust, or damage on the clamp
• The clamp not holding the hose securely in place

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Igniter Mounting Clip is an OEM part for Bosch ranges. It secures the igniter to the range top, ensuring it is properly aligned and stable for optimal ignition performance. The surface igniter is crucial for the ignition of gas burners, facilitating an immediate and safe flame to cook with.

Over time, the Igniter Mounting Clip can succumb to various forms of wear and tear, including corrosion from exposure to moisture, degradation from frequent heating cycles, or physical damage during cleaning or maintenance activities. 

Symptoms of a compromised Igniter Mounting Clip include:

• The surface igniter becoming loose or dislodged
• Difficulty in igniting the burner or uneven flames
• Noisy or irregular ignition sounds
• Visible signs of damage or corrosion on the clip

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

The Fastening Ring is an OEM part for Bosch front load washers. It secures the door boot seal to the front panel of the washer, ensuring a tight and leak-free connection. This ring is essential for maintaining the washer's seal during operation, preventing water from escaping the drum.

Causes of a bad fastening ring can include normal wear and tear, rust or corrosion, and damage from over-tightening or mishandling during maintenance.

Symptoms of a bad fastening ring include:

• Water leaking from the door area
• The door boot seal becoming loose or detached
• Visible damage or deformation of the ring

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

This clamp secures a wooden or custom exterior panel to the appliance door, restoring proper panel alignment and reducing rattling or looseness. Designed to match the OEM bracket location and fit. What it does:

• Holds the decorative wood panel firmly against the dishwasher door frame
• Prevents the panel from shifting, sagging, or vibrating during cycles
• Restores even door fit and helps maintain the door's seal and appearance
• Works at the bracket attachment point to stabilize panel-to-door connection

• Disconnect power to the appliance before beginning any work
• Remove the outer door panel per the service manual to access the clamp location
• Inspect surrounding clips and screws; replace any damaged fasteners for a secure fit

This sump clamp secures the dishwasher sump/drain assembly to the tub, keeping the seal and pump assembly held in place to prevent leaks and movement. It's a small but essential fastener for a watertight sump connection. What it does:

• Holds the sump/drain housing tightly against the tub to maintain a proper seal
• Prevents the sump assembly from shifting during operation, which can cause leaks or noise
• Helps stop water from leaking under the machine when the pump runs
• Supports proper alignment of the drain/pump components for reliable draining

• One sump clamp

• Disconnect power and water supply before starting any repair
• Access the sump area by removing the lower access panel or toe kick and tilting the machine as needed
• Inspect the sump seal/gasket and replace if cracked or damaged when replacing the clamp
• Tighten clip until secure but avoid forcing or deforming the sump housing; test for leaks after reassembly

This push-on retainer clip holds a 6mm shaft securely in place on compatible appliance components, restoring proper axial restraint and preventing parts from sliding off during operation. Simple, low-profile fastening for shaft retainment. What it does:

• Secures shafts and spindles with a 6mm outer diameter to prevent axial movement
• Keeps knobs, pulleys, or rotating components positioned correctly during use
• Commonly used where a quick, tool-free clip is required for retention
• Can resolve symptoms like loose or detached knobs, wobbling pulleys, or parts sliding along the shaft

• One push-on retainer clip sized for 6mm shaft mounting

• Push the clip onto the shaft groove until it snaps into place; ensure full engagement before operating
• Use snap-ring pliers or appropriate tools if removal is required to avoid damage
• Wear eye protection when installing or removing clips to guard against sudden release

This trim strip mounting clip secures the decorative door trim on dishwashers with short side panels, restoring a flush, stable front appearance and preventing the trim from rattling or coming loose. Ideal when the trim has shifted or separated. What it does:

• Secures the outer trim strip to the dishwasher door at short-side-panel mounting points.
• Keeps trim aligned and prevents rattling, sagging, or visible gaps.
• Restores the finished look of the dishwasher front after trim movement or damage.
• Works with the original trim assembly and mounting hardware to maintain proper fit.

• Always disconnect power to the appliance before accessing the door assembly and follow OEM service instructions.
• Access typically requires removing the inner or outer door panel or lower access panel; preserve existing screws and hardware for reassembly.
• Clip installs into the designated trim mounting location; confirm orientation before fastening and avoid over-tightening.
• Obtain the correct fasteners from the OEM parts list.

A small spring-style hose clamp used to secure flexible appliance hoses to fittings and prevent leaks. Simple, durable replacement that restores a tight connection for water and drain lines. What it does:

• Compresses around a hose to hold it firmly on an inlet, outlet or drain fitting
• Helps stop leaks caused by loose or slipping hoses
• Keeps hoses seated during normal appliance operation and vibration
• Commonly used on dishwasher and washer drain or water hoses

• One hose clip / spring clamp

• Disconnect power and water supply before starting repairs
• Use pliers to expand the clamp for removal and reinstall; ensure hose is fully seated before releasing clamp
• Inspect the hose and fitting for damage; replace any cracked or brittle hose
• Do not overtighten or deform clamp when installing; replace if corroded or weakened

This fastening ring secures a rotating or stationary component in place to help prevent movement and vibration. It restores proper fit and alignment so assemblies run quietly and components stay locked in position. What it does:

• Holds shafts, bearings or housings in position to prevent axial movement
• Helps stop rattling, wobble or misalignment caused by a loose retaining component
• Maintains a secure mechanical connection between mating parts
• Used wherever a snap/retaining ring is required to lock a component on a shaft or in a bore

• Disconnect power and water before beginning any repair
• Use the correct pliers or tools for snap/retaining rings to avoid deformation
• Verify the ring matches the OEM part number and seating location before installation

A small metal clip that secures the dryer to the top of the washer when stacking, keeping the pair stable during operation. Use this replacement clip if the original is bent, missing, or fails to hold the units together. What it does:

• Locks the dryer cabinet to the washer top to help prevent shifting or sliding during use
• Restores the mechanical fastening point used in factory stacking setups
• Common symptom: dryer feels loose or moves when the pair operate together
• Common symptom: visible bent, cracked, or missing clip at the stack connection

• Turn off and unplug both appliances before attempting installation
• Lift and support the dryer securely during alignment; use a second person or proper lifting equipment
• Slide or snap clip into the factory stacking locations per the appliance's service instructions

Drain hose clamp