Bosch Spring Parts

The Door Spring and Cable Kit is an OEM replacement part for Bosch dishwashers. This kit replaces both the spring and cable mechanism that operates the dishwasher door. 

Causes of a bad door spring and cable can include wear through extended usage cycles that degrade parts. Improper handling may also lead to damage over time.

Symptoms of issues with the spring and cable include:

• A door that does not close or latch securely  
• Difficulty smoothly opening and shutting the door
• Excessive noise and rattling from the spring mechanism

This OEM replacement part is compatible with select brands like Thermador and Gaggenau.

This door seal holding spring is the wire clamp that secures the washer's door boot to the front opening, keeping the seal seated to help prevent leaks and maintain a proper fit.

• Holds the door seal/boot firmly around the front panel opening
• Helps maintain a watertight seal during wash and spin cycles
• Replaces a stretched, broken, or missing clamp/spring
• Common symptoms: boot won't stay seated, water leaking at the door opening, visible broken/missing spring

• Disconnect power and turn off the water supply before servicing
• Open the door and carefully remove the existing clamp from the gasket groove; avoid puncturing the boot
• Reseat the boot evenly, then stretch and position the new spring/clamp around the groove (spring typically at the bottom)
• Test for leaks after reassembly

This dishwasher door spring counterbalances the door's weight for smooth, controlled opening and closing. Replacing a worn or broken spring restores proper door tension and helps prevent the door from dropping quickly or feeling heavy.

• Provides tension to counterbalance the dishwasher door during opening and closing
• Helps prevent the door from slamming open or feeling overly heavy
• A weakened or broken spring can cause uneven door movement, squeaks, or the door not staying in a partial-open position
• Restores smooth, even door operation when replaced

• Disconnect power and turn off water supply before servicing
• Remove the toe-kick and carefully slide the dishwasher out to access the side/frame area where the spring attaches
• Note the original spring attachment points and orientation; install the new spring in the same locations
• Springs are under tension—use caution and hand protection; many replace both springs together to maintain balanced tension

Replacement door hinge tension spring that restores proper door balance and smooth opening and closing on compatible Bosch appliances. Replaces a worn or broken door spring to help prevent sagging and doors that won't stay open. What it does:

• Provides counter-tension for the door hinge so the door stays level and moves smoothly.
• Restores proper balance to doors that feel heavy, sag, or close too quickly.
• Works as the return/tension element inside the hinge assembly to control door travel.
• Common repair for door sag, uneven closing, or doors that don't remain open.

• Disconnect power (or unplug) and remove water supply if working on dishwashers; follow all safety steps before servicing.
• Spring is under tension—wear eye protection and gloves; release or install slowly and carefully.
• May require removing the door panel or hinge caps.

Drum shock absorber for front-load washers. This damper connects the tub to the chassis and controls movement during wash and spin, reducing vibration and noise so the washer can ramp to proper spin speed without banging.

• Damps and stabilizes the drum to control vibration during acceleration, spin, and coast-down
• Helps reduce shaking, banging, and "walking" across the floor
• Can help address out-of-balance messages and noisy operation
• Worn shocks may leave loads wet after spin or cause loud thumping

• Disconnect power and shut off water before servicing; move the appliance to access panels safely
• Access the shock from the front or rear per model; support the tub to relieve tension
• Note pin/bolt orientation; transfer any reusable hardware and fully seat both ends of the new shock
• Consider replacing them as a set for balanced damping; run a short test cycle to verify stability

This washing machine shock absorber stabilizes the outer tub during wash and spin. Replacing a weakened damper helps control vibration and noise so the washer runs smoother and is less likely to shake, bang, or walk.

• Mounts between the tub assembly and cabinet/base to cushion movement
• Helps prevent excessive vibration, shaking, and thumping noises
• Can reduce "walking" or out-of-balance interruptions when a damper is worn
• Supports smoother, quieter spin performance

• Disconnect power and turn off water supply before servicing
• Remove the appropriate access panel(s) to reach the dampers
• Support the tub when removing mounting pins/bolts; match the original orientation
• Inspect all dampers; replace any that show wear for balanced performance