Bosch Dishwasher Parts

This cotton insulation piece provides noise- and heat-damping for the appliance cabinet area, helping reduce operating sound and limiting heat transfer around the tub. Designed to replace worn or damaged insulation for a snug fit and quieter operation. What it does:

• Reduces operating noise by adding a sound-dampening layer around the tub area
• Helps limit heat transfer from the heater/tub to surrounding panels
• Provides a protective barrier to reduce vibration-related noise
• Restores the original insulation barrier when the old material is compressed or torn

• One cotton insulation panel, white, 46 dB variant

• Disconnect power and water supply before beginning any service
• Handle the insulation gently to avoid tearing; wear gloves and a dust mask if needed
• Remove access panels and old insulation, then position and secure the new piece in the same orientation
• Reinstall panels and restore power; test for proper operation and reduced noise

This outer door panel is the exterior panel that restores the appliance's front appearance and protects internal door components. Replacing a damaged or dented outer panel brings back a flush, sealed door and improves the unit's look. What it does

• Covers and protects inner door components from impact, moisture, and wear
• Restores proper door alignment and helps maintain the cabinet seal
• Improves cosmetic appearance when the original panel is dented, scratched, or corroded
• Helps prevent debris from entering the door cavity and affecting internal parts

• One outer door panel

• Designed for compatibility with specific OEM door assemblies; fit for your model before ordering
• Handle and trim may need transfer from the old panel; your model's parts diagram
• Use appropriate fasteners and avoid overtightening to prevent panel distortion
• Disconnect power and water (if applicable) and follow general safety precautions before servicing

This inner door insulation replaces the insulating layer inside the appliance door to help maintain proper cooking or drying temperatures and reduce heat transfer to the outer door surface. It restores thermal performance and helps the door reach expected operating conditions. What it does:

• Replaces deteriorated or missing door insulation to reduce heat loss through the door
• Helps the appliance hold consistent internal temperatures for better cooking/drying results
• Can reduce outer door surface heat, lowering burn risk during normal operation
• Addresses issues like excessive door heat or long recovery times after opening the door

• One inner door insulation piece

• Disconnect power and allow the appliance to fully cool before starting work
• Installation typically requires removing the door outer panel; follow OEM instructions for your model
• Handle edges, clips, and panels carefully to avoid damage; use proper fasteners and orientation
• If adhesive or tape is present on the original part, replace with OEM-approved material when reassembling

Color: White

The Adjustable Tine Row is an OEM part for Bosch dishwashers. It is designed to hold and secure dishes, allowing for optimal placement and cleaning efficiency. The adjustable feature allows users to customize the spacing of the tines to accommodate various dish sizes and shapes.

Over time, the adjustable tine row can become damaged or worn out due to repeated use or excessive force when adjusting the tines. This can lead to difficulties in securing dishes properly and may impact the overall performance of the dishwasher.

Symptoms of a bad adjustable tine row include:

• Tines that are bent or broken
• Difficulty in adjusting the tine positions
• Dishes not staying in place during the wash cycle

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Insert is an OEM component specifically designed for select Bosch dishwashers. Located inside the tub basin, the tines provide the necessary friction to help clean dishes. 

Causes of a bad insert can include mineral buildup that prevents proper movement or damage from dropped utensils that have bent the tines out of place.

Symptoms of a bad insert include:

• Dishes still feeling dirty after the wash cycle   
• Rust or mineral deposits visible on the tines
• Tines that are bent or missing which reduces cleaning surface area

Replacing the insert with this OEM Bosch part restores optimal cleaning performance. Compatible with 300 series models, it features stainless steel construction that withstands corrosion from detergents. This replacement insert is warranted to perform as the original Bosch design for reliable dish cleaning.
 

The Dispenser is an OEM part for Bosch dishwashers. It dispenses detergent and rinse aid at appropriate times during the dishwashing cycle, ensuring optimal cleaning and rinsing performance. The dispenser is essential for maintaining the efficiency and effectiveness of your dishwasher.

Causes of a bad dispenser can include clogging from detergent residue, mechanical failure of the dispenser door or latch, or electronic issues that prevent proper operation. Regular cleaning and maintenance can help mitigate these problems, but parts may still need replacement over time.

Symptoms of a bad dispenser include:

• Inconsistent or improper dispensing of detergent or rinse aid
• Dishwasher leaving spots or residue on dishes
• The dispenser door not opening during the cycle
• Leaks or drips from the dispenser area

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Dishrack Roller is an OEM replacement part for Bosch dishwashers. Located inside the tub, this roller assists with moving upper and lower dishracks in and out during operation. 

Causes of failure are prolonged exposure to detergent residues combined with repeated rolling impact stresses absorbing dishrack weight for tens of thousands of cycles.

Symptoms of a worn or damaged dishrack roller include:  

• Difficulty fully extending or retracting dishrack shelves  
• Rack skew or tilting sideways instead of moving smoothly
• Grinding or scraping noises heard from the tub area  
• Dishes not lining up properly to receive spray patterns

This genuine Bosch roller is also compatible with Thermador and Gaggenau models.

The Push Button Set is an OEM part for Bosch dishwashers. This set includes the buttons used to operate various functions on the dishwasher’s control panel. The buttons are designed to fit within the control interface, allowing users to easily select and adjust washing cycles and settings.

Causes of a bad push button set can include regular wear and tear from frequent use, exposure to moisture or cleaning chemicals, or physical damage from impacts. 

Symptoms of a bad push button set include:

• Buttons not responding when pressed
• Buttons getting stuck or not depressing fully
• Inconsistent or erratic operation of the dishwasher controls
• Visible wear or damage to the buttons

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.

The Bearing is an OEM component specifically designed for select Bosch dishwashers requiring stabilized rotational movement. As a friction-reducing fixture, it facilitates the smooth operation of assorted mechanisms.  

Precision-ground steel and reinforced polymer composite withstand harsh chemicals and high spinning velocities without excess heat or noise. Independent shielding maintains lubrication without contaminating surrounding compartments.

Causes requiring bearing replacement usually involve coolant deterioration building friction. Physical impacts may dislodge protective seals exposing components to intrusions no longer offering intended cushioning.

Symptoms signaling the need for a new bearing incorporate:

• Grinding or scraping noises emitting from moving joints
• Reduced cycle speeds from binding components  
• Excessive rotational resistance detected by diagnostics sensors

This OEM Bosch replacement bearing is also compatible with Thermador, Gaggenau, and some Kenmore dishwashers relying on long-lasting suspension elements. Proper installation restores noise-dampening characteristics throughout operational stresses.