Bosch Dishwasher Parts

Bushing included. To order bushing separately use 00165296. This is the right side hinge. For left side hinge use 00263115.

This black replacement door handle restores a dishwasher's exterior grip and appearance, letting the door open and close securely. It matches factory fit and finish for compatible Bosch dishwasher models. What it does:

• Replaces a cracked, broken or missing door handle to restore normal door opening
• Provides a solid grip for pulling the dishwasher door open and closed
• Restores the appliance's exterior appearance when the original handle is damaged
• Fits the factory handle mounting locations and aligns with the door trim

• One black door handle

• Disconnect power to the dishwasher before starting any repair
• Support the door while removing fasteners to prevent it from closing unexpectedly
• Remove interior door panel or trim as required to access handle screws or clips
• Use manufacturer service manual or OEM instructions for step-by-step removal and reassembly

This actuator lever assembly with springs replaces a worn or broken control lever to restore proper mechanical movement in the appliance. It helps the dispenser/latch mechanism operate smoothly for reliable everyday use. What it does:

• Transfers motion from a control cam or motor to the latch or dispenser linkage
• Restores proper engagement when a broken or fatigued lever prevents operation
• Helps stop intermittent or failed cycle starts caused by damaged mechanical linkage
• Works as a direct-fit replacement that re-establishes spring tension and lever action

• Disconnect power before accessing internal components to avoid shock or injury
• Basic hand tools usually required; maintain original screw/hardware if reusing
• Inspect surrounding linkages and replace damaged clips or fasteners as needed

This door latch cover is the exterior trim that fits over the dishwasher door latch, restoring a finished appearance and protecting the latch mechanism from spills and wear. It matches stainless-steel finishes and keeps the latch area clean. What it does:

• Covers and protects the door latch assembly from moisture and grime.
• Restores the dishwasher door's exterior appearance when dented, scratched, or missing trim.
• Helps prevent debris build-up that can interfere with latch engagement.
• Compatible with latch installations that use a snap-on or screw-attached cover.

• Remove power to the appliance before starting any repair to avoid electrical hazard.
• Remove the inner door panel or access trim per service instructions to reach latch area.
• Install by aligning the cover over the latch and securing with the original screws or clips; do not force or bend the cover.
• If metal damage or latch misalignment is present, inspect latch mechanism and replace if necessary.

A small spring-style hose clamp used to secure flexible appliance hoses to fittings and prevent leaks. Simple, durable replacement that restores a tight connection for water and drain lines. What it does:

• Compresses around a hose to hold it firmly on an inlet, outlet or drain fitting
• Helps stop leaks caused by loose or slipping hoses
• Keeps hoses seated during normal appliance operation and vibration
• Commonly used on dishwasher and washer drain or water hoses

• One hose clip / spring clamp

• Disconnect power and water supply before starting repairs
• Use pliers to expand the clamp for removal and reinstall; ensure hose is fully seated before releasing clamp
• Inspect the hose and fitting for damage; replace any cracked or brittle hose
• Do not overtighten or deform clamp when installing; replace if corroded or weakened

A replacement flip tine for the dishwasher lower rack that restores folding rack supports so you can load dishes of different sizes. Bright silver finish matches common rack coatings for a discreet repair. What it does

• Replaces a single lower-rack flip tine used to fold down and support dishes, bowls and glasses.
• Restores the rack's ability to flip tines up or down for flexible loading.
• Helps stop dishes from shifting during the wash cycle when a tine is broken or missing.
• Fits into the lower rack's tine socket and functions with the existing rack hardware.

• One silver lower-rack flip tine (single piece).

• Slide or snap the tine into the lower rack tine socket until it seats; no special tools usually required.
• Inspect surrounding rack coating and mounting clip before installing; replace damaged clips or rack parts if needed.
• Handle edges carefully; wear gloves to avoid cuts on metal rack parts.
• Disconnect power to the appliance before doing any repairs that require more than simple hand installation.

This retaining clip secures small appliance components in place to prevent movement and ensure reliable part alignment. It provides a simple, durable hold that keeps assemblies stable during normal use and service. What it does:

• Holds panels, covers, or wiring harnesses in position to prevent rubbing or disconnection
• Maintains alignment of moving or attached components to reduce noise and wear
• Helps prevent intermittent electrical or mechanical failures caused by loose parts
• Commonly replaced when broken, cracked, or missing after service or impact

• One retaining clip

• Basic hand tools may be required; inspect surrounding parts before reassembly
• Wear gloves and power off and unplug the appliance before servicing
• Replace only with the correct OEM-designated clip to ensure fit and function

This is the left hinge cap. For right hinge cap use 00165295.

This door latch cover is a direct-fit replacement trim piece that protects and conceals the dishwasher door latch assembly while restoring a finished appearance. Keeps the latch area tidy and helps ensure the door closes cleanly. What it does:

• Covers and protects the door latch mechanism from debris and wear
• Helps the door latch engage and the door sit flush when closed
• Restores the appliance's cosmetic finish around the latch area
• Can address symptoms such as a loose-looking latch area or an unsealed door edge

• Disconnect power to the appliance before installing; follow lockout/tagout practices
• Basic hand tools (screwdriver or trim tool) are typically required to remove the old cover
• Align the new cover over the latch assembly and snap or fasten into place per OEM diagram
• If the latch mechanism or strike is damaged, replace those parts as needed for full repair

A reed switch door sensor that detects when the appliance door is closed so the control can start cycles. Replaces a failed magnetic sensor to restore reliable door-closed detection and normal operation. What it does

• Acts as a magnetic contact that signals the control when the door or lid is closed
• Helps prevent the appliance from starting if the door is open or not fully latched
• Common symptom fix for no-start, intermittent cycle start, or control not recognizing a closed door
• Works as the electrical switching element in the door/detector assembly

• One reed switch (single replacement sensor)

• Disconnect power to the appliance before replacing the part to avoid shock or damage
• Handle the switch and wiring gently; avoid bending or stressing terminals and solder joints
• Locate and access the door/detector area per your service manual or tech sheet; confirm connector orientation before installing

This inner door is the interior panel for a dishwasher door that protects internal components and provides a finished inside surface. Replacing a damaged inner door restores proper sealing and appearance. What it does:

• Forms the interior surface of the dishwasher door and helps contain water during cycles
• Protects wiring, insulation, and electronics housed inside the door
• Helps maintain a proper seal to prevent leaks and improve wash performance
• Addresses symptoms like visible door damage, interior rust, dents, or moisture inside the door cavity

• Disconnect power and water supply before starting any repair
• Removing the outer door panel or control panel may be required;
• Keep fasteners and trim organized for reassembly; some clips or screws may be needed

This float switch lever is the actuator that moves the dishwasher's tub float to operate the water-level/flood-sensing switch, helping the appliance detect overfill and control fill/drain cycles. Replaces a worn or broken lever to restore proper float activation. What it does:

• Transfers movement from the tub float to the float switch so the machine senses water level correctly
• Commonly needed when a cracked or detached lever prevents the float from engaging the switch
• Can stop overfill-safety trips or no-fill symptoms caused by a non-responsive float assembly
• Works with the existing float and float switch; restores mechanical linkage function

• Disconnect power to the appliance before servicing to avoid shock or injury
• Remove lower access panels or tub components as required to reach the float assembly
• Inspect surrounding clips and the float for damage; replace any broken hardware
• Tighten securely but avoid over-torquing; test float movement and switch activation before reassembly

This door handle replaces a worn or broken appliance door grip to restore a secure, comfortable surface for opening and closing. Designed to match the original fit and appearance for easy cosmetic repair. What it does:

• Provides a sturdy grip for opening and closing the appliance door
• Replaces cracked, loose, or cosmetically damaged handles
• Restores proper leverage to reduce stress on the door latch and hinges
• Helps improve the look of the appliance by replacing a worn handle

• One door handle

• Refer to your appliance model's service manual for step-by-step removal and installation instructions
• Installation typically requires basic hand tools; disconnect power (and water if applicable) before servicing
• Handle may attach with screws or snap-fit clips—keep removed fasteners for re-use unless replacements are provided

This rubber gasket seals appliance openings to help prevent water and air leaks and restore proper door/tub sealing. It replaces a worn or damaged seal to reduce leaking and maintain normal appliance performance. What it does

• Creates a watertight/airtight barrier between mating surfaces to prevent leaks.
• Helps maintain operating temperature and efficiency by sealing the door/tub.
• Common symptom: visible water around the door or base during use.
• Common symptom: cracked, flattened, or distorted seal material that no longer compresses.
• Works as a direct replacement for the matching OEM seal when damaged or worn.

• One gasket as shown on the product page.

• Turn off power and water supply to the appliance before starting any repair.
• Remove the old seal carefully, clean the mounting channel of debris and residue, and inspect the mating surface.
• Press the new gasket evenly into the channel, starting at one corner and working around to ensure full seating without twists.
• Test the door closure and run a short cycle to confirm there are no leaks; re-seat if necessary.