Parts for Kitchenaid KFDC558JMB01: Burner Box And Griddle Parts

This replacement manifold assembly routes water through the appliance to maintain proper operation and consistent performance. It restores correct fluid distribution for cleaning and rinsing so cycles run as expected. What it does:

• Directs water to internal spray ports and chambers for normal cycle operation
• Ensures even water flow to improve cleaning and rinsing performance
• Stops leaks or flow loss when a cracked or damaged manifold is replaced
• Resolves symptoms like uneven cleaning, water pooling, or error codes related to water distribution

• One manifold assembly as shown

• Disconnect power and shut off water supply before starting repair
• Inspect and replace any worn gaskets, seals, or mounting hardware as needed
• Tighten fittings to OEM torque; avoid overtightening plastic fittings
• Run a test cycle and check thoroughly for leaks after installation

This replacement manifold routes and distributes incoming water to the dishwasher's spray and wash system to restore proper cleaning performance and eliminate leaks or poor water flow. Fits specific Whirlpool-built dishwasher assemblies. What it does

• Directs incoming water to spray arms and wash chambers for normal wash cycles
• Helps prevent leaks where the manifold connects to inlet or spray plumbing
• Can restore proper water flow if spray arms are not spraying or cleaning poorly
• Works with factory seals and mounting locations for a direct-fit replacement

• One replacement manifold

• Disconnect power and water supply before beginning any repair
• Inspect and replace associated seals or gaskets if they show wear or damage
• Tighten fasteners to manufacturer torque; avoid overtightening plastic fittings

This manifold directs gas from the oven's gas valve to the burner ports, restoring proper gas flow for consistent burner operation. Replaces a worn or cracked manifold to help burners light evenly and maintain safe combustion. What it does

• Routes gas from the main valve to the oven/burner ports for ignition.
• Restores even burner flames when a cracked or clogged manifold causes weak or no flame.
• Helps stop intermittent heating when distribution passages are blocked or damaged.
• Supports proper sealing and alignment for safe gas flow to burners.

• Manifold assembly

• Turn off gas supply and electrical power before starting; follow all safety precautions.
• Inspect gaskets, seals and mounting hardware; replace damaged components as needed.
• Tighten fittings to manufacturer torque specs and test all connections for leaks with a gas-safe method.

This wire harness is the appliance's pre-assembled electrical connector assembly that routes power and signals between controls and components, restoring reliable electrical connections and component operation. What it does:

• Routes power and control signals between the control board, motors, sensors and other components
• Replaces damaged, frayed or corroded wiring that can cause intermittent operation or component failure
• Restores proper connector fit and secure electrical contact to prevent arcing or loss of function
• Helps resolve symptoms such as no power to a circuit, intermittent operation, or components that won't respond

• One wire harness assembly as shown

• Disconnect power (unplug or switch off breaker) before beginning any work
• Compare the replacement harness to the original to ensure connector types and lengths before installation
• Route and secure wires following original clips and fasteners; avoid pinching or sharp bends

This speaker module provides audible tones and chimes used by the appliance to signal cycle progress and user alerts. It restores clear sound feedback so you can hear cycle completion, alerts, and error tones. What it does:

• Produces the appliance's audible chimes, beeps, and alert tones
• Signals cycle completion and user prompts with clear sound
• Helps indicate error codes and status changes through audible alerts
• Interfaces with the main control to provide user feedback

• Disconnect power to the appliance before servicing to avoid electrical shock
• Handle the module and wiring harness carefully; avoid static discharge and bent pins
• Reconnect the wiring harness fully and secure the module in its mounting location
• Test the appliance after installation to ensure audible tones function correctly

The Range Screw is an OEM part for Whirlpool ranges. It is a small but essential component used to secure various parts and panels of the range. It is designed to fit securely into pre-drilled holes, holding components tightly in place.

There are a few factors that can lead to a bad Range Screw. Over time, screws may become loose or stripped due to frequent use or inadequate tightening. Accidental cross-threading or overtightening can also damage the screw or the surrounding components.

Symptoms of a bad screw may include loose or wobbly parts, rattling noises during operation, or difficulty in keeping components securely attached. This OEM Whirlpool part can also be used on Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore/Sears brand appliances.

This 1/2" female adapter is a threaded plumbing connector that lets a 1/2" male water line or fitting join the appliance inlet safely and securely. It provides a simple, durable connection to restore proper water flow. What it does:

• Adapts a 1/2" male threaded water supply to the appliance's inlet fitting
• Restores a secure, leak-free connection when the original fitting is damaged or missing
• Commonly used where a reliable, compact threaded coupling is needed
• Can help stop drips or leaks caused by worn or corroded connectors

• One 1/2" female adapter

• Turn off the water supply and unplug the appliance before installing
• Use plumber's tape on threads for a reliable seal unless the OEM instructions specify otherwise
• Hand-start threads to avoid cross-threading, then tighten with an appropriate wrench; avoid over-tightening
• Check connections for leaks after restoring water and operation

The Drip Tray is an OEM component designed specifically for Whirlpool ranges. Located underneath the range's bottom heating elements, the tray collects moisture, melted cheese, or other baked-on messes during cooking. Its indented surface area and angled drainage grooves route debris toward an easily removed drip cup.

Causes of a bad drip tray can include scorched grease that accumulation makes thorough cleaning difficult or impact dents that cause leakage. 

Symptoms of a bad drip tray include:

• Excessive residue buildup outside the designated drainage path  
• Stains or water marks appearing on surrounding cabinetry
• Drip cup overflowing due to impaired drainage route
• Difficulty removing tray for cleaning of hardened messes

This OEM Whirlpool part is compatible with KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore wall oven and range models. 

The range conversion kit is an OEM component specifically designed for Whirlpool ranges. This kit contains all the necessary parts to convert a range from natural gas to propane gas or vice versa. 

Symptoms of an incompatible or incorrectly installed conversion kit include:

• Incomplete or unstable burning of the gas 
• Yellow burner flame tips instead of blue
• Higher than normal gas usage
• Issues with ignition or flammability 

Causes of a bad conversion kit could be improper installation, damaged or missing components, or using a kit not designed for the specific range model.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Screws for range anti tip bracket: WP3801F656-51. Includes 2 screws.