Parts for Electrolux EFMC427UIW1: Burner Parts

The Heater is an OEM replacement part for Frigidaire dryers. It is responsible for generating the heat necessary to dry clothes efficiently during the drying cycle. The heater works in conjunction with the dryer’s thermostat and other components to maintain the appropriate temperature for optimal performance.

Over time, the dryer heater can fail due to wear and tear, electrical issues, or overheating caused by restricted airflow or clogged lint filters. A malfunctioning heater will prevent the dryer from achieving the temperatures needed for effective drying.

Symptoms of a bad dryer heater include:

• Clothes remaining damp or wet after a full drying cycle
• The dryer not producing any heat during operation
• Unusual smells, such as burning or overheating odors
• Error codes indicating heating issues

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This mounting bracket secures internal components to the appliance chassis, restoring proper alignment and stability. Replaces a broken or bent bracket to stop loose parts, rattling, or misaligned panels for safer, quieter operation. What it does:

• Provides a rigid attachment point for panels, assemblies, or hardware to the cabinet or frame
• Prevents movement that can cause rattling, scraping, or uneven gaps
• Restores correct alignment so related parts operate smoothly
• Helps maintain safe spacing and support for adjacent components

• One mounting bracket as shown

• Disconnect power (and water, if applicable) before installing
• Handle metal edges carefully; wear gloves to avoid cuts
• Use the existing fasteners when possible; replace damaged screws if needed

This is a Phillips pan head machine screw commonly used to secure panels and components in appliances. It provides a reliable, low-profile head for flush fastening and easy Phillips-driver installation. What it does:

• Fastens trim, panels, or internal components where a pan head screw is required
• Designed for secure grip in metal or threaded inserts compatible with #10-16 threads
• Helps prevent loosening from vibration when installed to correct torque
• Often used in refrigeration and major appliance assemblies in limited quantities

• One Phillips pan head screw (#10-16 x 5/8")

• Use the correct #2 Phillips driver and steady pressure to avoid cam-out or stripping
• Do not overtighten; stop when snug to avoid damaging threads or mating parts
• Replace only with an identical thread size and head style to ensure fit
• Wear safety glasses when working around sharp sheet metal and springs

A single replacement screw used to secure appliance trim, panels, or interior components. Replaces lost or damaged fasteners so panels and assemblies stay firmly attached and appliances operate safely. What it does:

• Secures trim pieces, control panels, brackets, or interior components
• Restores proper fit and alignment when panels are loose or rattling
• Helps eliminate vibration noise caused by missing or stripped screws
• Used wherever the OEM screw specification is required for reliable fastening

• Install with the matching screwdriver or driver bit; avoid over-tightening to prevent stripping
• Disconnect power and remove or support panels as needed for safe access
• If screw threads are damaged, replace with the exact OEM screw to ensure secure fit

The Inlet Thermal Fuse is an OEM part for Frigidaire laundry centers. It serves as a safety device to prevent the washer from overheating by cutting off electrical power if the temperature exceeds safe levels.

Causes of a bad inlet thermal fuse can include electrical issues such as short circuits, prolonged exposure to high temperatures, or wear and tear from regular use.

Symptoms of a bad inlet thermal fuse include:

• The washer not starting or stopping mid-cycle
• No power to the washer, even when plugged in
• Error codes indicating thermal issues
• The washer overheating during operation

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The High Limit Thermostat is an OEM part for Frigidaire dryers. It serves as a critical safety device, designed to cut off the power to the heating element if the dryer overheats. This thermostat helps prevent potential fire hazards by maintaining a safe operating temperature within the dryer.

Symptoms of a bad High Limit Thermostat include:

• The dryer not heating up at all, indicating that the thermostat may have tripped or failed permanently.
• Dryer repeatedly shutting off during cycles, which can be a sign that the thermostat is tripping too frequently due to overheating issues.
• Excessive heat in the dryer, suggesting that the thermostat is not functioning properly and failing to regulate the temperature.

Causes of a bad high limit thermostat can include restricted airflow due to a clogged lint filter or venting system, malfunctioning heating elements that generate excessive heat, or simply the thermostat wearing out over time.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.