Parts for Electrolux EIGD55HIW0: 11 - Burner Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

A single replacement screw used to secure appliance trim, panels, or interior components. Replaces lost or damaged fasteners so panels and assemblies stay firmly attached and appliances operate safely. What it does:

• Secures trim pieces, control panels, brackets, or interior components
• Restores proper fit and alignment when panels are loose or rattling
• Helps eliminate vibration noise caused by missing or stripped screws
• Used wherever the OEM screw specification is required for reliable fastening

• Install with the matching screwdriver or driver bit; avoid over-tightening to prevent stripping
• Disconnect power and remove or support panels as needed for safe access
• If screw threads are damaged, replace with the exact OEM screw to ensure secure fit

The Limiter is an OEM replacement part for Frigidaire dryers. Also called a high-limit thermostat, it prevents the dryer from overheating in the event of an obstruction or blockage. The limiter monitors air temperature and airflow inside the dryer drum. 

Symptoms of a bad limiter include:

• The dryer not heating up at all or heating intermittently
• Error codes or failure codes displayed 
• Smelly exhaust from the dryer vent
• Slow or inefficient drying times
• Dryer will not start at all

Causes of a bad limiter can be normal wear and tear over time, failure of internal components, or exposure to overheating conditions from blockages or items not suitable for machine drying. 

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

The High Limit Thermostat is an OEM part for Frigidaire dryers. It serves as a critical safety device, designed to cut off the power to the heating element if the dryer overheats. This thermostat helps prevent potential fire hazards by maintaining a safe operating temperature within the dryer.

Symptoms of a bad High Limit Thermostat include:

• The dryer not heating up at all, indicating that the thermostat may have tripped or failed permanently.
• Dryer repeatedly shutting off during cycles, which can be a sign that the thermostat is tripping too frequently due to overheating issues.
• Excessive heat in the dryer, suggesting that the thermostat is not functioning properly and failing to regulate the temperature.

Causes of a bad high limit thermostat can include restricted airflow due to a clogged lint filter or venting system, malfunctioning heating elements that generate excessive heat, or simply the thermostat wearing out over time.

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This electrical wiring harness connects and routes power and signals between fridge components, restoring reliable electrical continuity so controls, lights, and motors can operate correctly. Use this direct-replacement harness to repair damaged or worn wiring. What it does

• Routes power and signal connections between control boards, compressors, valves, lights, and sensors
• Restores lost or intermittent electrical connections that can cause controls to fail or components to stop working
• Prevents shorts and open circuits when damaged wires or broken connectors are replaced
• Matches OEM connector types and wire lengths for a direct-replacement fit

• One electrical harness

• Disconnect power at the breaker or unplug the appliance before inspecting or replacing the harness
• Compare connector shapes and wire colors to the original harness to ensure correct installation
• Secure wires away from moving parts and sharp edges; avoid pinching or excessive bending

This mounting bracket secures internal components to the appliance chassis, restoring proper alignment and stability. Replaces a broken or bent bracket to stop loose parts, rattling, or misaligned panels for safer, quieter operation. What it does:

• Provides a rigid attachment point for panels, assemblies, or hardware to the cabinet or frame
• Prevents movement that can cause rattling, scraping, or uneven gaps
• Restores correct alignment so related parts operate smoothly
• Helps maintain safe spacing and support for adjacent components

• One mounting bracket as shown

• Disconnect power (and water, if applicable) before installing
• Handle metal edges carefully; wear gloves to avoid cuts
• Use the existing fasteners when possible; replace damaged screws if needed

The Ignitor is an OEM part for Frigidaire dryers. This part ignites the gas burner that generates the heat necessary for drying clothes.  Note: Part has been redesigned and is now a flat style ignitor instead of round ignitor.

Causes of a bad Ignitor can include wear and tear from regular use, electrical issues such as short circuits or power surges, and physical damage from debris or residue buildup.

Symptoms of a bad Ignitor include:

• The dryer not heating up, leading to clothes remaining wet after a cycle
• The ignitor not glowing or sparking when the dryer is turned on
• Extended drying times due to insufficient heat production
• The smell of gas without ignition, indicating a failure to light the burner

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This is a replacement mounting collar used to secure and align associated appliance components for proper fit and operation. It restores the original spacing and support where the factory collar is worn or damaged. What it does:

• Provides a secure mounting point to hold panels, assemblies, or shafts in correct alignment
• Helps prevent excess movement that can cause noise, vibration, or premature wear
• Restores proper spacing to prevent rubbing or binding of adjacent parts
• Useful when a cracked, deformed, or missing collar causes misalignment or rattling

• Always disconnect power to the appliance before beginning repairs to avoid shock or injury
• Inspect surrounding parts and mounting hardware; replace any damaged fasteners for a secure fit
• Hand-start fasteners to avoid cross-threading, then tighten to OEM torque if specified

This burner assembly restores proper gas flame and heat in your dryer. It directs and mixes gas and air for clean ignition at the igniter, helping clothes dry efficiently and consistently.

• Provides the flame path and mixing chamber for gas ignition
• Helps resolve symptoms like no heat, intermittent heat, or very long dry times
• Can address issues where the burner won't ignite or the flame will not stay lit
• Designed to fit the factory burner mount and align with the igniter and flame sensor

• Disconnect power and shut off gas supply before servicing; allow the appliance to cool
• Access is typically from the front lower panel or burner compartment
• Transfer any reusable hardware from the original assembly if required
• After reassembly, restore gas and check all connections for leaks using a soapy water solution

This electrical wiring harness routes power and signals between components to restore reliable electrical connections. It replaces a damaged or worn harness to correct intermittent power, nonresponsive controls, or component failures. What it does:

• Carries electrical power and control signals between appliance modules and components
• Restores lost or intermittent electrical continuity caused by frayed wires or broken connectors
• Helps resolve symptoms like lights or components not powering on, sporadic operation, or control failures
• Maintains factory routing and connector fit for proper electrical performance

• Disconnect power before attempting any repair to avoid shock or damage
• Compare connectors and wire colors to the old harness to ensure correct replacement
• Use proper strain relief and routing to prevent chafing or pinching of wires

The Dryer Heat Sensor is an OEM part for Frigidaire dryers. This sensor monitors the temperature inside the dryer drum to ensure clothes are dried effectively and safely by regulating the heat levels during the drying cycle.

Causes of a bad heat sensor can include wear and tear from frequent use, buildup of lint or debris, or electrical issues. A malfunctioning sensor can result in incorrect temperature readings, leading to under-drying or overheating of clothes.

Symptoms of a bad Dryer Heat Sensor include:

• Clothes not drying properly or taking too long to dry
• Dryer overheating or shutting off unexpectedly
• Inconsistent drying cycles
• Error codes related to temperature control

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

This replacement tube routes defrost melt and condensation away from the freezer compartment to the drain pan, helping prevent leaks and ice buildup. Fits specific Frigidaire refrigerator models—check product fit for compatibility. What it does:

• Channels defrost water from the evaporator area to the drain system to prevent pooling
• Helps stop ice accumulation that can block drains and reduce cooling efficiency
• Restores proper water flow when original tube is cracked, split, or clogged
• Compatible direct-replacement when matched to the appliance model/PN

• Disconnect power before starting any repair to avoid electrical shock
• Use appropriate clamps or retainers from the appliance as originally installed; replace damaged clips if needed