Parts for Electrolux FPGH3077RFA: 03 - Burner Parts

This water inlet valve controls water flow to the appliance, restoring normal filling for the dispenser and ice maker. It replaces a failed valve to stop leaks and resume steady water delivery. What it does

• Opens and closes to allow water into the ice maker or dispenser when signaled
• Commonly used when the ice maker won't fill or the dispenser has weak/no water flow
• Can prevent continuous running or leaking if the valve sticks closed or open
• Works as a direct replacement for the appliance's original inlet valve assembly

• Disconnect power and shut off the water supply before starting work
• Verify the inlet and outlet hose connections and seals are tight after installation
• Handle with care to avoid damaging mounting tabs or solenoid wiring

This safety valve controls gas flow to the oven burner. When signaled by the igniter, it opens to allow ignition and helps maintain consistent heat, supporting safe, reliable preheating and baking performance.

• Regulates gas flow to the oven burner under control of the igniter and thermostat/electronic control
• Prevents gas from flowing until proper ignition conditions are met
• Common symptoms: oven won't ignite or heat, intermittent heating, extended preheat time, or weak/unstable flame
• Often inspected when the igniter glows but the burner does not light

• Disconnect power and shut off the gas supply before servicing
• Transfer any model-specific fittings or brackets from the original valve
• Use approved thread sealant on threaded connections; support tubing and avoid overtightening
• After installation, leak-check every connection with a soap-and-water or leak-detection solution

This safety valve controls gas flow to the oven burner, opening only when the ignition system calls for heat. Replacing a weak or stuck valve restores reliable ignition and consistent oven temperatures for safe, dependable baking and roasting. What it does:

• Regulates and shuts off gas to the oven burner circuit
• Works with the igniter; opens only when proper current is present
• Fails closed to help prevent unlit gas from entering the oven
• Common symptoms may include: oven won't heat, intermittent heating, very long preheat, or a weak/unstable flame

• 1 safety valve

• Disconnect power and shut off gas supply before servicing
• Label and transfer all tubing and wires from the original valve one-for-one
• Support flare fittings with two wrenches; use thread sealant only on NPT threads (never on flare connections)
• After installation, restore gas and check every joint for leaks with an approved leak-detection solution

If your range has intermittent controls or non-responsive buttons, the wiring harness may be damaged. This harness restores reliable signal transfer.

Secures the ignitor assembly to your gas cooktop burner base. Replace if screw head is stripped, threads damaged, or screw is missing after disassembly.

This surface burner element replaces a damaged or non-working electric cooktop heating element to restore normal cooking heat and even heating across cookware. It fits compatible Frigidaire electric ranges and stoves. What it does:

• Heats cookware by converting electrical power into cooking heat for stovetop use.
• Replaces an element that fails to heat, gets intermittently hot, or shows visible burns or breaks.
• Restores even cooking when the original burner is warped, cracked, or has poor contact.
• Works with existing terminal block and cooktop connections when the mount and wiring are intact.

• One surface burner element (single replacement).

• Disconnect power to the range at the circuit breaker before starting any work.
• Allow the cooktop and element to cool completely; element terminals can be sharp—wear gloves.
• Remove the old element by pulling straight out from the terminal block and align the replacement for a snug, secure fit.

If your range burner won't heat or heats unevenly, this burner element restores proper cooking performance. Common DIY repair, typically 15-30 minutes.

Replacement surface burner head for gas ranges and cooktops. Distributes gas through precision ports for even flame. Needed when original is clogged, damaged, or corroded.

Replacement burner head for gas ranges and cooktops. Mounts over the orifice to distribute flame evenly. Needed when original is cracked or damaged.

Replaces a cracked, corroded, or damaged burner on your gas range or cooktop. Installs on top to restore the heat source for your cooking zone.

Replacement gas burner for ranges and cooktops. Restores even flame distribution when original is clogged, damaged, or worn from boilovers and daily use.

Gas oven won't light or ignites slowly? A clogged or worn ignitor orifice assembly disrupts gas flow to the burner. Direct replacement restores reliable ignition.

This ignitor orifice assembly delivers and directs gas to the oven ignitor so burners light reliably. It restores proper gas flow at the ignitor for consistent ignition and safer oven operation in gas ranges and wall ovens. What it does:

• Directs gas from the valve to the oven ignitor so the burner can ignite
• Helps eliminate no-heat or weak-flame symptoms when the ignitor area is the issue
• Supports stable, consistent ignition timing and flame establishment
• Replaces a damaged, clogged, or corroded orifice/ignitor connection

• One ignitor orifice assembly

• Turn off gas supply and electrical power before beginning work
• Handle carefully; avoid bending the orifice and keep ignition surfaces clean
• Basic hand tools are typically required
• After installation, check for gas leaks and test oven ignition in a well-ventilated area

If your oven burner won't light or has delayed ignition, this ignitor orifice assembly restores proper gas flow and spark alignment for reliable starts.

Ignitor orifice assembly meters and directs gas for reliable oven burner ignition. Replace when burners won't light or ignite inconsistently. Verify fit.

This ignitor orifice assembly secures the oven igniter and directs gas to the oven burner for consistent ignition. It's a direct-replacement part used to restore proper spark/ignition performance on compatible gas ovens. What it does:

• Holds and positions the oven igniter and orifice for reliable flame initiation
• Directs gas flow to the burner so the igniter can light the oven
• Commonly replaces worn, clogged, or damaged assemblies that cause ignition delays or no-heat conditions
• Helps restore safe, consistent oven ignition when the igniter itself is functioning

• Disconnect power and shut off the gas supply before beginning any service
• Handle components carefully; avoid bending or damaging the orifice or ignitor mounting

Replacement tube for your range. This part connects internal components for proper appliance operation. Replace if cracked, leaking, or damaged during service work.

Regulates gas flow from the supply line to your range burners. Replace if cracked, leaking, or damaged to restore proper fuel control and flame size.

Controls gas flow to your range oven burners. Replace if the valve is leaking, won't shut off completely, or has damaged threads or connections.

This replacement surface burner restores stovetop heating for electric ranges, providing a direct, reliable heat source for pots and pans. Designed to match the original element shape and fit for a straightforward swap. What it does:

• Heats cookware on the cooktop so you can boil, simmer, and sauté
• Replaces a cracked, warped, or non-heating burner element
• Addresses symptoms such as little or no heat, intermittent heating, or uneven hot spots
• Works with the existing burner receptacle and cooktop cutout when the correct element is used

• One round surface burner element

• Disconnect power to the range before servicing to avoid electrical shock
• Remove the cooktop or lift the burner assembly per your model's service instructions
• Align and seat the element into the socket, then secure any mounting clips or screws as originally installed

Replace a cracked, damaged, or missing baffle in your gas range. This structural component installs inside the oven cavity to direct airflow properly.

Broiler won't light or heat? This range broil ignitor ignites the top broiler burner. Common fix when broiler fails to start or brown food properly.

The Ignitor is an OEM replacement part for Frigidaire gas ranges. Located near the burner heads, this component is responsible for generating the electric spark required to light stove top burners.

Symptoms of a faulty ignitor include:

• Burners that will not light or only light intermittently
• Clicking noises but no flame ignition
• Diminished or no spark from the ignitor itself

Causes of ignitor failure can be an accumulation of deposits over many heating cycles. Physical damage from pots/pans is also possible. As electrical parts, ignitors have a limited lifespan depending on range usage.

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The Screw is an OEM part for Frigidaire ranges and cooktops. This part secures the burner head in place, ensuring proper alignment and functioning of the burner.

Causes of a bad burner head screw can include loosening due to repeated heating and cooling cycles, damage from impact or mishandling, or simply wear and tear over time.

Symptoms of a loose or missing burner head screw include:

• Uneven or irregular flame pattern on the burner
• Burner head not sitting flush or properly aligned
• Burner head wobbling or moving during use
• Potential gas leaks if the burner head is not securely fastened

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Secures gas valve assemblies and mounting brackets to your range. Replace if screw is stripped, missing, or corroded to keep valve hardware stable.

Converting your range from natural gas to liquid propane? This LP conversion kit replaces orifices to restore proper burner flames and safe operation.

Fix intermittent power or control issues in your gas range with this wiring harness. Restores electrical connectivity between components. DIY repair.

Mounting screw for securing range panels, brackets, and igniters. Replace if stripped, missing, or damaged to restore proper fastening and alignment.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.

Chrome screw secures handles, door trim, and internal components in ranges and ovens. Replace if lost during cleaning, stripped, or missing after moves.