Parts for Roper B8758X0: 04 - Burner Parts

This is a package of twelve replacement nuts used to secure appliance panels and components. These genuine-style nuts restore fastener retention to reduce looseness and rattling and help keep parts aligned during operation. What it does:

• Secures panels, brackets, and fasteners to maintain proper component alignment
• Prevents vibration-related loosening that can cause noise or intermittent contact
• Replaces missing or damaged nuts that can allow parts to shift or fall off
• Used wherever the matching nut size and thread are required by the appliance

• Disconnect power (and gas, if applicable) before servicing the appliance.
• Verify the nut size and thread match the stud or bolt before installation.
• Hand-start threads, then tighten with the appropriate driver or wrench; avoid overtightening.

Specs: 10-16 x 1/2 inch.

The Oven Bake and Broil Igniter is an OEM part for Whirlpool ovens. It is designed to ignite the gas in both the bake and broil burners, ensuring efficient and safe operation of the oven. This dual-function igniter provides reliable ignition for a consistent baking and broiling experience.

You should replace the oven bake and broil igniter if it becomes faulty. Causes of a bad igniter can include electrical failures, wear and tear from repeated use, or damage from thermal stress. These issues can prevent the igniter from reaching the necessary temperature to ignite the gas.

Symptoms of a bad oven bake and broil igniter include:

• The oven not heating up
• The broiler not working
• A delayed ignition or no ignition at all
• The oven taking longer than usual to reach the desired temperature

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This control valve is an important safety feature found on many gas ranges. It's located inside the back of the range near the area where the buttons and controls are found. The reason the control valve is included in ovens is to prevent gas from moving to the burners if the igniter is not able to ignite the gas or there is no electricity. The control valve could be faulty if there is a smell of gas near the valve, the burner flame flickers, or the flame cannot be turned on high.In any of these situations, the control valve must be replaced. The repair is easy and takes only a few minutes. The bottom of the oven will need to be removed, which may require a screwdriver. After removing it, remove the flame spreader by taking out two screws and sliding it out of the oven. Remove the screw holding the oven burner tube and take it out to access the valve and replace it.This control valve is made to be compatible with RCA, Kenmore, Roper, General Electric, and Hotpoint ranges. It's sold as an individual OEM replacement part that is sourced directly from the manufacturer.

This replacement screw secures appliance panels and components. Use this OEM fastener to swap out stripped, corroded, or missing hardware so assemblies stay tight, aligned, and quiet for reliable day-to-day operation.

• Provides secure attachment for panels, brackets, and internal assemblies
• Direct replacement for stripped, corroded, or lost screws
• Can help with symptoms like vibration, rattling, or loose/misaligned parts
• Supports proper fit to reduce gaps or unwanted movement

• Disconnect power; for gas or water appliances, shut off the supply before service
• Note hardware order and retain any spacers or clips from the original setup
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the mating part before installation

Screw: 8-16 x 3/8 inch.

This cover screw secures appliance panels and covers, keeping components protected and aligned. Replace missing, stripped, or corroded screws to restore a tight fit and help eliminate rattles, gaps, or panels that won't stay in place.

• Attaches an access cover or panel to the appliance frame
• Helps maintain proper alignment to protect internal components
• Replaces missing, stripped, or rusted hardware
• Typical signs: loose or rattling panel, cover won't stay secure, damaged or rounded screw head

• Disconnect power before servicing
• Support the panel while removing and installing screws to prevent misalignment
• Start threads by hand to avoid cross-threading; do not overtighten
• Use a matching driver bit to avoid damaging the screw head

Nickel

This replacement screw secures appliance panels, brackets, and internal components so your unit stays assembled, aligned, and quiet. Use it to replace missing, stripped, or corroded hardware and restore a reliable factory-fastened connection.

• Fastens panels, brackets, or trim to the cabinet/frame
• Helps maintain proper alignment of doors, controls, or covers
• Replaces hardware that's missing, rusted, or with a stripped head
• Can help reduce vibration or rattling from loose fasteners

• Disconnect power and shut off gas/water supplies before service
• Match thread and length to the original; transfer any washers if present
• Start threads by hand to avoid cross-threading, then tighten with the correct driver
• Do not overtighten; snug until secure to prevent damage to plastic or sheet metal