Parts for Thermador PRD364EDPG-01: Burners Parts

This is a surface burner cap. Surface burner caps are installed on range cooktops. The function of the burner cap is to protect the head of the burner. It keeps food and other debris from falling into the burner head and also helps to create a more even heating surface by spreading out the flame. With use, because of misuse, or from accidental damage, the surface burner cap may stop working correctly. When it stops functioning, it requires a replacement to continue efficiently using the appliance.Checking the burner cap for signs of damage should be enough to tell whether or not this part should be replaced. If the flame on the cooktop isn't spreading out and heating evenly, the burner cap may be faulty. A replacement part is simple to install. Make sure the range is turned off. Unplug it from the power source to prevent a spontaneous ignition while placing the surface burner cap on the device.This surface burner cap is an authentic OEM replacement part. It is sourced by the manufacturer. It is sold as an individual unit. The surface burner cap is made of high-quality, durable materials. It can be installed on cooktops in various range models. It is compatible with Bosch, Thermador, and Gaggenau brand equipment.

The Venturi Gas Tube is an OEM replacement part for Bosch gas cooktop ranges. Its primary function is to ensure an optimal gas/air mixture for consistent and efficient burner combustion, thereby enhancing the overall performance of the cooktop.

Causes involve normal wear of internal components from continuous heating and cooling cycles. Corrosion damage may also disrupt the venturi tube over time.

Symptoms of a faulty venturi gas tube include:

• Unstable or hard-to-control flame levels
• Potential issues shifting burner flames out of their intended position
• Safety risks including carbon monoxide from improper fuel/air balance

This OEM Bosch part is also compatible with Thermador, Gaggenau and some Kenmore models.

The Ignition Device is an OEM part for Bosch ranges. It is responsible for sparking the flame that ignites the burners. 

Causes of a bad Ignition Device can include worn out or damaged elements, moisture or debris buildup causing faulty sparking, or corrosion of electronic components. 

Symptoms of a bad Ignition Device include:

• Burners that will not light or stay lit
• Continuous sparking at burners even when flames are present 
• Ignition clicking but no flame ignition
• Flickering or unstable flames

This OEM Bosch part is also compatible with Thermador, Gaggenau, and some Kenmore models.
 

This connector strip is the wire terminal block that joins appliance wiring harnesses for reliable electrical connections, helping restore power and control signal continuity. It's a direct-fit replacement when the original connector is damaged or burned. What it does:

• Provides a secure termination point for multiple wires so circuits can complete and controls receive power.
• Replaces corroded, loose, or burned terminals that cause intermittent power, no-heat or no-power issues.
• Maintains correct wiring alignment to prevent shorts or poor contact.
• Helps eliminate symptoms like a blank display, burners or elements not powering, or sporadic operation tied to a bad connection.

• Always disconnect power to the appliance (unplug or switch off breaker) before inspecting or replacing electrical parts.
• Verify wire locations and take a photo before removal to preserve proper wiring order.
• Replace only if terminals are visibly damaged, loose, or show signs of burning; secure all screws/nuts to factory tightness.

Used to hold down the jet holder assembly.

The Surface Burner Holder is an OEM part for Bosch ranges and cooktops. It serves to securely mount and support both the surface burner assembly and gas orifices in place on the cooktop. 

Causes of a faulty or damaged burner and orifice holder can include wear from heavy daily cooking demands, broken mounting tabs due to impact or dropped cookware, or corrosion affecting the burner and orifice fittings over many years.

Symptoms of failure include:

• Gas leaks at burner and/or orifice connections
• Difficulty achieving proper burner ignition
• Burners that are loose, wobbly or unstable during cooking
• Inability to effectively seal the burner and orifice assembly into position

This genuine OEM Bosch part is also compatible with Thermador, Gaggenau and select Kenmore models.

This tension spring secures and balances moving assemblies, restoring proper door or component tension and smooth operation. Use it to replace a worn, stretched, or broken spring for reliable mechanical return force. What it does:

• Provides restoring tension to a door, latch, or moving linkage so it closes or returns smoothly
• Replaces weakened or broken springs that cause sagging, loose movement, or improper latching
• Helps correct symptoms like noisy operation, parts that won't stay closed, or uneven movement
• Works as a direct-fit replacement when the original spring has lost tension or snapped

• One replacement tension spring

• Turn power off and disconnect the appliance before servicing to avoid injury
• Inspect surrounding clips, pins, or mounting points and replace any damaged hardware
• Use pliers or appropriate tools to remove/install the spring carefully; springs can snap back