Parts for Electrolux EFDC317TIW3: Cabinet / Drum Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This replacement cushion is a small rubber bumper that protects components and reduces vibration and noise where panels, doors, or assemblies meet. It helps keep parts aligned and prevents metal-on-metal contact. What it does:

• Absorbs shock and reduces vibration to minimize rattling or movement
• Protects surfaces from wear and prevents scraping or chafing
• Helps maintain proper spacing or alignment of panels or assemblies
• Works wherever a soft bumper or spacer is required

• Disconnect power to the appliance before servicing.
• Remove any covers or panels to access the mounting area.
• Press or seat the cushion into the locator/receptacle; replace retainers if present.

The Duct is an OEM part for Frigidaire dryers. It is responsible for proper airflow and ventilation within the dryer, ensuring efficient drying.

A bad dryer air duct with grille cover can be caused by clogs, damage, or improper maintenance. Signs of a faulty air duct include restricted airflow, longer drying times, or excessive heat buildup within the dryer.

Symptoms of a bad duct can include:

• Clothes taking longer to dry than usual
• Reduced airflow from the dryer vent
• Excessive heat or overheating 

Replace your clogged or damaged dryer air duct with this genuine OEM part to restore your dryer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This insulator is a small foam/trim piece that cushions and thermally isolates appliance panels to help maintain proper airflow and reduce vibration. It preserves fit between cabinet components for quiet, efficient operation. What it does:

• Cushions panels and components to reduce rattling or vibration noise
• Creates a thermal barrier that helps limit heat transfer between parts
• Keeps panels aligned and spaced to prevent rubbing or abrasion
• Worn or missing insulators can cause noise, vibration, or poor panel fit

• One insulator as shown

• Disconnect power before accessing panels or internal components
• Replace only the worn or damaged insulator; trim or adhesive may be needed to position some styles
• Remove surrounding trim or panels as required to reach the mounting location

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This thermistor is the temperature-sensing component that feeds accurate readings to the appliance's control. Replacing a faulty sensor restores proper temperature feedback, helping the control run cycles correctly and reduce temperature-related performance issues. What it does:

• Monitors temperature and changes resistance with temperature (NTC), sending a signal to the control board
• Helps the control regulate heating or water-temperature management during operation
• When open/shorted or out of range, can trigger temperature/sensor error codes
• Symptoms include inconsistent temperatures, long run times, or cycles that won't complete

• 1 thermistor

• Disconnect power before servicing; shut off gas/water supply if applicable
• Access the sensor per your model; it's typically secured by a clip or screw and connects via a wire harness
• Note wire orientation; avoid pulling on wires and ensure the connector is fully seated
• After installation, clear any stored error codes and run a diagnostic or test cycle

This replacement seal restores a tight barrier between mating surfaces in your appliance, helping contain air, moisture, and heat where intended for reliable performance and efficiency.

• Forms a tight barrier to help prevent leaks, drafts, or heat loss
• Replaces a cracked, torn, flattened, or missing seal
• Can help address issues like moisture around an opening, temperature fluctuations, or rattling/vibration from a poor fit
• Restores proper closure and performance when the original seal is worn

• Disconnect power and shut off water/gas before service
• Note the routing/orientation of the original seal; take photos for reference
• Clean the channel/mating surfaces thoroughly; remove old adhesive and debris
• Seat the new seal fully without stretching; close and test for proper fit and contact

This main control board is the appliance's central electronic controller, replacing a faulty control module to restore normal oven/range functions and reliable user interface operation. It manages timers, key inputs and control signals to heating elements and displays. What it does:

• Controls bake/ broil/ self-clean cycles and regulates signals to the appliance's heating and safety systems
• Processes front-panel inputs and drives the display, timers and electronic indicators
• A failing board can cause unresponsive buttons, blank or erratic displays, or appliances that won't start or complete cycles
• Works with door lock, ignitor and sensor circuits as the main command and timing hub

• Disconnect power to the appliance before servicing to avoid shock or damage
• Handle the board by the edges and avoid static discharge; use an anti-static wrist strap if available
• Verify all wiring connections and fuses before and after installation

This support bracket secures and stabilizes internal components to keep your appliance operating reliably. It provides a simple, durable mounting point to restore proper alignment and reduce movement or rattling. What it does:

• Provides a secure mounting point for internal panels or assemblies
• Helps prevent component shift that can cause noise or misalignment
• Restores part-to-part spacing for proper operation
• Replaces damaged, bent, or broken brackets that no longer hold components

• Disconnect power before accessing internal panels or mounting points
• Installation may require removal of the appliance access panel and basic hand tools
• Retain and reuse original fasteners if undamaged; use OEM-specified hardware when required

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

This vane directs airflow inside the appliance to help control cooling or venting. Replacing a damaged vane restores proper airflow and helps maintain even temperature and efficient operation. What it does

• Guides and directs internal air flow for proper ventilation or cooling.
• Helps seals and channels air to prevent uneven temperature or poor performance.
• Worn or broken vanes can cause reduced airflow, noisy operation, or improper venting.
• Small, molded part designed to fit in the OEM mounting location and work with the appliance's blower/damper assembly.

• One vane

• Disconnect power to the appliance before starting any repair to avoid shock or injury.
• Access may require removing panels or other components; keep fasteners organized for reassembly.
• Inspect surrounding seals and mounting points and replace any damaged clips or screws.

This drum mixing vane is a molded white lifter that helps tumble and redistribute laundry inside the drum for more even agitation and drying. It replaces a worn or broken vane to restore normal clothing movement and prevent fabric bunching. What it does:

• Lifts and tumbles load as the drum rotates to promote even cleaning and drying
• Helps separate garments to reduce tangling and clumping during cycles
• Restores proper drum contact when existing vanes are cracked, loose, or missing
• Compatible with models using a molded white mixing/drum vane design

• One white drum mixing vane

• Remove power and disconnect the appliance before starting any repair
• Inspect mounting boss and fasteners; replace any damaged clips or screws
• Push or snap the vane into the drum mounting location per OEM alignment; verify a secure fit before testing

This spacer is a small positioning piece used to maintain the correct gap and alignment between adjoining components, helping prevent rubbing, noise, or uneven operation.

• Maintains proper spacing between parts for smooth, reliable function
• Helps reduce vibration, rattling, or wear from misaligned components
• Commonly needed when a spacer is missing, damaged, or worn
• Symptoms can include noise, looseness, or parts that don't sit flush

• Disconnect power (and shut off water or gas, if applicable) before starting
• Note the spacer's orientation and placement during disassembly
• Replace any damaged fasteners or clips as needed
• Do not overtighten adjacent hardware to avoid deforming the spacer

Replacement shaft that restores proper rotation and alignment for the appliance's moving components. Use this shaft to replace a worn or damaged spindle and help reduce noise, wobble, and interrupted operation. What it does:

• Transfers rotation between connected moving parts so the appliance can operate smoothly.
• Replaces a bent, worn, or broken shaft that can cause vibration or binding.
• Commonly used when the appliance makes unusual noises, vibrates excessively, or stops turning.
• Helps re-establish correct alignment to prevent premature wear of adjacent components.

• Disconnect power before beginning any repair to avoid shock or injury.
• Keep track of fasteners and any spacers/retainers removed during disassembly.
• Basic hand tools are usually required; avoid forcing parts to prevent damage.

The Roller Wheel Assembly is an OEM part for Frigidaire dryers. It is designed to support the dryer drum and facilitate its smooth rotation during the drying cycle. 

Over time, the roller wheel assembly can become worn out or damaged. Causes of a bad roller wheel assembly can include regular wear and tear from continuous use, accumulation of lint and debris, or damage from overloading the dryer. These factors can lead to the rollers becoming worn or misaligned, affecting the dryer's operation.

Symptoms of a bad roller wheel assembly include:

• Squeaking or thumping noises during the drying cycle
• The drum not rotating smoothly or being off-balance
• Increased drying times due to inefficient drum movement
• Visible wear or damage to the rollers

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Replacement metal mounting nut that secures panels, brackets or small assemblies on Frigidaire appliances. Restores a secure fastening point to reduce wobble, rattling or parts that feel loose or shift during use. What it does:

• Threads onto the matching stud or bolt to hold panels, trim or brackets in place
• Keeps components aligned and prevents movement or vibration
• Helps stop rattling, loose control panels, or parts that pull away from the cabinet
• Simple hardware solution when a corroded or missing nut causes a loose connection

• Disconnect power (or unplug) before accessing internal panels or assemblies
• Use the correct-size wrench or socket; turn clockwise to tighten, counterclockwise to loosen
• Tighten securely but avoid overtightening to prevent thread damage or stripped studs
• If threads are damaged or stud is bent, replace the damaged stud/fastener

The Leveling Leg is an OEM part for Frigidaire dryers. It adjusts to stabilize the dryer on uneven floors during operation.

Subjected to vibrations, repeated adjustments expose leveling legs to wear over extended use. Causes of damage include common plastic stress fractures.

Causes of a problematic leveling leg can include:

• Loosened mounting allowing dryer movement
• Deformed, cracked or damaged plastic dampening
• Inability to adjust height or reliably stabilize weight

Symptoms include:

• Excessive shaking or noise related to an uneven base
• Difficulty configuring proper ventilation clearances
• Premature component fatigue accelerating repairs

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

Hex washer head ,10-32 x 0.375. Ground

This door gasket is the refrigerator/freezer door seal that helps keep cold air inside for consistent temperatures and efficient operation. It replaces a worn or torn seal to reduce drafts and moisture buildup. What it does:

• Creates an airtight seal around the door edge to help maintain interior temperature
• Reduces frost, condensation, and energy loss from a leaking door
• Helps keep stored food fresher by preventing warm-air intrusion
• Addresses common symptoms like visible gaps, tears, or a door that won't stay cold

• One door gasket

• Inspect the door and frame for damage or debris before installing the new gasket
• Clean mounting surface and follow OEM alignment steps for a proper seal
• Warm the gasket slightly (per OEM guidance) if needed to ease installation and improve fit

This is a Phillips pan head machine screw commonly used to secure panels and components in appliances. It provides a reliable, low-profile head for flush fastening and easy Phillips-driver installation. What it does:

• Fastens trim, panels, or internal components where a pan head screw is required
• Designed for secure grip in metal or threaded inserts compatible with #10-16 threads
• Helps prevent loosening from vibration when installed to correct torque
• Often used in refrigeration and major appliance assemblies in limited quantities

• One Phillips pan head screw (#10-16 x 5/8")

• Use the correct #2 Phillips driver and steady pressure to avoid cam-out or stripping
• Do not overtighten; stop when snug to avoid damaging threads or mating parts
• Replace only with an identical thread size and head style to ensure fit
• Wear safety glasses when working around sharp sheet metal and springs

This terminal block provides the mounting point and secure electrical connection for the appliance power leads. Replacing a damaged or corroded terminal block restores a solid power connection and reduces arcing or intermittent power. What it does:

• Provides a secure connection between the incoming power cord and the appliance wiring
• Holds and isolates power terminals to prevent shorting and arcing
• Commonly fails when terminals are burned, corroded, loose, or when wires heat at the connection
• Symptoms of a failing terminal include loss of power, intermittent power, visible burn marks or arcing at the connection, and melted or discolored insulation

• One terminal block

• Always disconnect power at the breaker or unplug the appliance before servicing
• Tighten mounting screws and terminal screws securely; inspect and replace any damaged wire insulation

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.