Parts for Electrolux EIMGD55IMB2: 03 - Cabinet / Drum Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This is a metal or plastic bracket that serves as a protective cover over the terminal block where the power cord connects to the dryer. It shields the electrical connections from accidental contact and helps prevent short circuits. Replace this part if it is cracked, missing, or damaged - an exposed terminal block is a safety hazard.

One per package.

Plastic cap cover for dryer installation. Replaces cracked, broken, or missing covers. Snaps into place to provide clean finished appearance.

Rubber cushion bumper for dryers. Installs between panels or assemblies to reduce vibration and noise. Replace if cracked, worn, or missing.

Dryer duct that routes hot air through the ventilation system. Replace if cracked, warped, scorched, or causing debris to attach to clothing during cycles.

Foam insulator strip that cushions dryer panels and reduces vibration. Replace if worn, compressed, or missing to maintain quiet operation and fit.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Fix a dryer that won't shut off automatically or has temperature control issues. This thermistor sensor monitors heat levels for proper cycle operation.

This moisture sensor consists of two metal strips typically mounted inside the dryer drum area that detect the moisture level in clothing during a drying cycle. It signals the control board to end the cycle when clothes reach the desired dryness. Replace this sensor if your dryer shuts off too early with clothes still damp, runs too long, or if the auto-dry cycle no longer functions properly.

Replacement mounting bracket for dryers and laundry centers. Secures internal components in place. Order a new bracket if yours is cracked or broken.

Replacement base for your dryer. Supports the cabinet and internal components. Needed when original is cracked, rusted, or structurally damaged.

Control panel for your dryer. Mounts on the front of the unit and houses the control interface. Replace if cracked, damaged, or worn from regular use.

Secures internal components in your dryer. Replace this mounting bracket if cracked, broken, or missing to restore proper alignment and stability.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

This straight drum baffle creates tumbling action inside your dryer drum to lift and separate clothes for even drying. It extends from the drum wall to catch and lift garments as the drum rotates. Replace this baffle if clothes aren't drying evenly, take longer to dry, or if the original baffle is cracked or missing.

Gray molded paddle that lifts and tumbles clothes inside the dryer drum. Replace if cracked, broken, warped, or pulled loose from the drum wall.

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

Support bracket for dryer assembly. Mounts and secures internal components in place. Replace if cracked, bent, broken, or missing to restore proper fit.

Washer that fits between the support roller and shaft in your dryer. Replace if worn, cracked, or missing to maintain proper drum alignment and support.

Supports and guides the dryer drum as it rotates. Replace if the roller is cracked, worn, or causing noise. Sold individually, not pre-assembled.

Replacement nut that secures internal components in dryers. Restores clamping force when original nut is stripped, worn, or missing. Prevents loosening.

Steam hose kit connects water source to dryer steam system. Includes rubber fill hoses and Y connector. Replace if hoses are cracked or leaking.

Rubber grommet cushions wiring, tubes, or panels in your dryer. Replace if cracked, worn, or missing to prevent chafing and reduce vibration noise.

This replacement nozzle assembly directs and controls water flow in the appliance, restoring proper delivery to the dispenser or ice-making components. It replaces a worn or damaged nozzle to help stop leaks and restore consistent flow. What it does

• Directs water from the supply line to the dispenser or ice-making fill tube.
• Helps stop spraying or leaking when the original nozzle is cracked or blocked.
• Restores steady water flow when the dispenser produces weak or intermittent water.
• Fits into the original mounting and seals the water path when properly installed.

• One nozzle assembly as shown.

• Turn off water supply and unplug the appliance before starting work.
• Inspect surrounding seals and tubing; replace any damaged parts to ensure a proper seal.
• Hand-tighten fittings and check for leaks after restoring power and water.

This replacement nozzle assembly directs and controls water flow in the appliance, restoring proper delivery to the dispenser or ice-making components. It replaces a worn or damaged nozzle to help stop leaks and restore consistent flow. What it does

• Directs water from the supply line to the dispenser or ice-making fill tube.
• Helps stop spraying or leaking when the original nozzle is cracked or blocked.
• Restores steady water flow when the dispenser produces weak or intermittent water.
• Fits into the original mounting and seals the water path when properly installed.

• One nozzle assembly as shown.

• Turn off water supply and unplug the appliance before starting work.
• Inspect surrounding seals and tubing; replace any damaged parts to ensure a proper seal.
• Hand-tighten fittings and check for leaks after restoring power and water.

Secures components inside your dryer to prevent shifting during operation. Replace this retainer if it's damaged, missing, or broken to eliminate noise.

Wire harness that connects control board, sensors, and electrical components in your dryer. Replace if wires are damaged, connectors are broken, or worn.

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.