Parts for Electrolux ELFG7637BT0: Cabinet / Drum Parts

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This replacement cushion is a small rubber bumper that protects components and reduces vibration and noise where panels, doors, or assemblies meet. It helps keep parts aligned and prevents metal-on-metal contact. What it does:

• Absorbs shock and reduces vibration to minimize rattling or movement
• Protects surfaces from wear and prevents scraping or chafing
• Helps maintain proper spacing or alignment of panels or assemblies
• Works wherever a soft bumper or spacer is required

• Disconnect power to the appliance before servicing.
• Remove any covers or panels to access the mounting area.
• Press or seat the cushion into the locator/receptacle; replace retainers if present.

A replacement exhaust duct that routes airflow between internal components and the exterior, helping restore proper ventilation and reduce leakage or noise. Use when damaged, cracked, or misaligned ducting affects appliance venting. What it does

• Channels airflow from the appliance to the exhaust path to maintain proper ventilation.
• Helps prevent air leaks that can reduce performance or cause overheating.
• Replaces damaged, cracked, or collapsed ducting that may cause whistling or rattling.
• Supports sealed airflow to help maintain consistent internal temperatures.

• Disconnect power (and gas if applicable) before starting any repair.
• Basic hand tools typically required; avoid forcing components to prevent cracking.

This insulator is a small foam/trim piece that cushions and thermally isolates appliance panels to help maintain proper airflow and reduce vibration. It preserves fit between cabinet components for quiet, efficient operation. What it does:

• Cushions panels and components to reduce rattling or vibration noise
• Creates a thermal barrier that helps limit heat transfer between parts
• Keeps panels aligned and spaced to prevent rubbing or abrasion
• Worn or missing insulators can cause noise, vibration, or poor panel fit

• One insulator as shown

• Disconnect power before accessing panels or internal components
• Replace only the worn or damaged insulator; trim or adhesive may be needed to position some styles
• Remove surrounding trim or panels as required to reach the mounting location

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

The Inlet Thermistor is an OEM part for Frigidaire dryers. It is responsible for monitoring the temperature of the incoming air to ensure proper drying and prevent overheating.

A bad inlet thermistor can be caused by electrical issues, sensor failure, or damage due to excessive heat or moisture. Signs of a faulty thermistor include the dryer not drying clothes properly, overheating, or shutting off prematurely.

Symptoms of a bad inlet thermistor can include:

• Clothes taking longer than usual to dry 
• Overheating of the dryer 
• The dryer shutting off before the clothes are fully dry 

Replace your malfunctioning inlet thermistor with this genuine OEM part to restore your dryer. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This replacement seal restores a tight barrier between mating surfaces in your appliance, helping contain air, moisture, and heat where intended for reliable performance and efficiency.

• Forms a tight barrier to help prevent leaks, drafts, or heat loss
• Replaces a cracked, torn, flattened, or missing seal
• Can help address issues like moisture around an opening, temperature fluctuations, or rattling/vibration from a poor fit
• Restores proper closure and performance when the original seal is worn

• Disconnect power and shut off water/gas before service
• Note the routing/orientation of the original seal; take photos for reference
• Clean the channel/mating surfaces thoroughly; remove old adhesive and debris
• Seat the new seal fully without stretching; close and test for proper fit and contact

This electronic control board manages a refrigerator's main functions so the appliance runs on its programmed cycles and user settings. Replacing a faulty control restores proper timing and coordination of cooling, defrost and user-interface functions. What it does

• Regulates compressor and evaporator fan cycles to manage cooling and temperature control.
• Controls timed defrost cycles and defrost heater activation.
• Communicates with the user interface/display and door/light circuits.
• Fault symptom linkage: needed if display is blank or unresponsive, cycles stop, defrost does not start, or the appliance shows error codes related to control failures.

• Disconnect power to the appliance before servicing to avoid shock or damage.
• Label and photograph wiring connections before removal; replace connectors exactly as found.
• Avoid excessive force; handle the board by edges and protect against electrostatic discharge.
• After installation, restore power and verify normal operation and that previous symptoms are resolved.

This support bracket secures and stabilizes internal components to keep your appliance operating reliably. It provides a simple, durable mounting point to restore proper alignment and reduce movement or rattling. What it does:

• Provides a secure mounting point for internal panels or assemblies
• Helps prevent component shift that can cause noise or misalignment
• Restores part-to-part spacing for proper operation
• Replaces damaged, bent, or broken brackets that no longer hold components

• Disconnect power before accessing internal panels or mounting points
• Installation may require removal of the appliance access panel and basic hand tools
• Retain and reuse original fasteners if undamaged; use OEM-specified hardware when required

No.8 pan head `10 - 10b x 0.50 `cr/sq drive

This replacement air baffle vane directs cooled air inside the refrigerator to help maintain even temperature distribution and proper airflow between compartments. Replaces a cracked or missing vane to restore intended airflow control. What it does:

• Directs and channels cold air from the evaporator to the refrigerator/freezer compartments
• Helps reduce uneven cooling and temperature stratification
• Prevents excessive airflow in one area that can cause frost buildup or warm spots
• Replaces broken, cracked, or warped vanes that rattle or obstruct airflow

• Disconnect power before beginning any repair to avoid electrical hazard
• Access typically requires removing shelves or the evaporator cover; keep parts organized
• Handle gently to avoid cracking the replacement vane during installation
• Use basic hand tools;

This drum mixing vane is a molded paddle that helps lift and tumble clothes inside the dryer drum for more even drying and reduced tangling. It's a direct-replacement style piece that restores proper fabric movement and airflow. What it does:

• Resets the drum's internal lift so garments rotate and tumble evenly during the dry cycle
• Helps prevent clothes from bunching or wrapping around the drum
• Promotes consistent airflow by keeping items off the drum surface
• Fits into the drum interior at a mounting point and engages with normal drum rotation

• One drum mixing vane (gray)

• Replace only with the dryer unplugged and the gas supply turned off (if applicable)
• Access requires opening the dryer cabinet or removing the drum
• Inspect the mounting boss and fastener before installing; use OEM fasteners if required

The Cord is an OEM replacement part for Frigidaire washing machines. Extending from the rear of the unit, it safely powers the washer through a connection to a wall outlet.

Causes of cord failure are normal wear from frequent coiling and plugging/unplugging motions over the appliance's lifespan. Rodents or sharp edges may also damage the outer jacketing.

Signs of a bad cord include:

• Exposed or severed copper wiring visible inside
• External cracks, splits or abrasions eroding the casing  
• Erratic behavior during the wash cycle
• GFCI/EGCI outlet tripping frequently

Compatible models also include Electrolux, KitchenAid, Jenn-Air, and Kenmore options. Maintaining safety is a top priority.

This spacer is a small positioning piece used to maintain the correct gap and alignment between adjoining components, helping prevent rubbing, noise, or uneven operation.

• Maintains proper spacing between parts for smooth, reliable function
• Helps reduce vibration, rattling, or wear from misaligned components
• Commonly needed when a spacer is missing, damaged, or worn
• Symptoms can include noise, looseness, or parts that don't sit flush

• Disconnect power (and shut off water or gas, if applicable) before starting
• Note the spacer's orientation and placement during disassembly
• Replace any damaged fasteners or clips as needed
• Do not overtighten adjacent hardware to avoid deforming the spacer

This metal drive shaft connects rotating components to transfer torque from the motor to driven parts, restoring proper rotation and alignment. It's a direct-replacement service part for affected Frigidaire appliances. What it does:

• Transfers rotational force from the motor or gearbox to the drum, agitator or other driven component
• Restores proper alignment and reduces wobble or binding caused by a worn or bent shaft
• Can eliminate grinding or scraping noises tied to a damaged shaft
• Helps re-establish secure mounting for collars, bearings or couplers that ride on the shaft

• Disconnect power (and water if applicable) before starting any repair
• Inspect surrounding bearings, seals and couplers; replace if worn to avoid premature failure
• Light press-fit or set-screw fastening may require basic hand tools; do not hammer the shaft into place

The Roller Wheel Assembly is an OEM part for Frigidaire dryers. It is designed to support the dryer drum and facilitate its smooth rotation during the drying cycle. 

Over time, the roller wheel assembly can become worn out or damaged. Causes of a bad roller wheel assembly can include regular wear and tear from continuous use, accumulation of lint and debris, or damage from overloading the dryer. These factors can lead to the rollers becoming worn or misaligned, affecting the dryer's operation.

Symptoms of a bad roller wheel assembly include:

• Squeaking or thumping noises during the drying cycle
• The drum not rotating smoothly or being off-balance
• Increased drying times due to inefficient drum movement
• Visible wear or damage to the rollers

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Replacement metal mounting nut that secures panels, brackets or small assemblies on Frigidaire appliances. Restores a secure fastening point to reduce wobble, rattling or parts that feel loose or shift during use. What it does:

• Threads onto the matching stud or bolt to hold panels, trim or brackets in place
• Keeps components aligned and prevents movement or vibration
• Helps stop rattling, loose control panels, or parts that pull away from the cabinet
• Simple hardware solution when a corroded or missing nut causes a loose connection

• Disconnect power (or unplug) before accessing internal panels or assemblies
• Use the correct-size wrench or socket; turn clockwise to tighten, counterclockwise to loosen
• Tighten securely but avoid overtightening to prevent thread damage or stripped studs
• If threads are damaged or stud is bent, replace the damaged stud/fastener

The Leveling Leg is an OEM part for Frigidaire dryers. It adjusts to stabilize the dryer on uneven floors during operation.

Subjected to vibrations, repeated adjustments expose leveling legs to wear over extended use. Causes of damage include common plastic stress fractures.

Causes of a problematic leveling leg can include:

• Loosened mounting allowing dryer movement
• Deformed, cracked or damaged plastic dampening
• Inability to adjust height or reliably stabilize weight

Symptoms include:

• Excessive shaking or noise related to an uneven base
• Difficulty configuring proper ventilation clearances
• Premature component fatigue accelerating repairs

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

A replacement threaded screw used to secure appliance panels and components, restoring proper fit and preventing rattles. Matches the OEM 1/4-14 x 3/8 size for fast, reliable repairs. What it does:

• Secures trim, panels, brackets or small assemblies to prevent movement and vibration
• Restores proper alignment when original screws are missing or stripped
• Common symptom fix: loose or rattling panels, unsecured components, or missing hardware

• Disconnect power to the appliance before servicing to avoid electrical or injury hazards
• Use the correct driver or socket to avoid stripping the head; start threads by hand
• Tighten until snug—do not overtighten to prevent stripping or damaging panels
• Keep removed hardware organized; fit before final assembly

The Water Valve is an OEM part for Frigidaire dryers featuring a steam cycle option. This valve controls the flow of water into the dryer drum during steam cycles.

Causes for replacement typically relate to standard wear and tear issues compromising the valve's ability to regulate water precisely during steam cycles. Mineral buildup from hard water sources can also obstruct full valve movement.

Symptoms of a faulty steam dryer water valve include:

• Inability to select steam cycle options
• Error codes related to steam or water systems
• Inconsistent steam levels during cycles

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

This rubber grommet cushions and secures wiring, tubes, or panels to prevent chafing and reduce vibration. It helps keep components aligned and quiet for reliable appliance operation. What it does:

• Cushions parts where metal meets metal to prevent wear and chafing
• Dampens vibration and reduces rattling or squeaking noises
• Holds wiring or tubing in place to maintain proper routing
• Helps protect against abrasion and occasional minor movement

• Disconnect power and leave appliance unplugged before starting any repair
• Remove the damaged grommet and clean surrounding area before installing the new piece
• Press or stretch the grommet into place; use gentle tools (plastic trim tool) to avoid damage
• Inspect adjacent wiring/tubing for damage and replace if frayed or pinched

This replacement nozzle assembly directs and controls water flow in the appliance, restoring proper delivery to the dispenser or ice-making components. It replaces a worn or damaged nozzle to help stop leaks and restore consistent flow. What it does

• Directs water from the supply line to the dispenser or ice-making fill tube.
• Helps stop spraying or leaking when the original nozzle is cracked or blocked.
• Restores steady water flow when the dispenser produces weak or intermittent water.
• Fits into the original mounting and seals the water path when properly installed.

• One nozzle assembly as shown.

• Turn off water supply and unplug the appliance before starting work.
• Inspect surrounding seals and tubing; replace any damaged parts to ensure a proper seal.
• Hand-tighten fittings and check for leaks after restoring power and water.

Hex washer head ,10-32 x 0.375. Ground

This is a Phillips pan head machine screw commonly used to secure panels and components in appliances. It provides a reliable, low-profile head for flush fastening and easy Phillips-driver installation. What it does:

• Fastens trim, panels, or internal components where a pan head screw is required
• Designed for secure grip in metal or threaded inserts compatible with #10-16 threads
• Helps prevent loosening from vibration when installed to correct torque
• Often used in refrigeration and major appliance assemblies in limited quantities

• One Phillips pan head screw (#10-16 x 5/8")

• Use the correct #2 Phillips driver and steady pressure to avoid cam-out or stripping
• Do not overtighten; stop when snug to avoid damaging threads or mating parts
• Replace only with an identical thread size and head style to ensure fit
• Wear safety glasses when working around sharp sheet metal and springs

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.