Parts for Electrolux FGVU17F8QWA: 03 - Cabinet Parts

Water pooling in freezer? This drain screen traps debris before it clogs the drain tube. Quick snap-in replacement restores proper drainage flow.

Fixes uneven cooling or warm top shelves in freezers. This blower wheel restores proper air circulation when the fan stops moving cold air effectively.

This is a lower breaker strip (divider panel) that fits along the interior of the freezer compartment. It serves as a trim piece that covers the gap between the liner and the outer cabinet, helping to insulate and provide a finished appearance. Replace this part if it is cracked, warped, or missing, which can allow cold air to escape and cause frost buildup or temperature inconsistencies.

This is a plastic breaker strip that fits along the upper area of the freezer compartment, serving as a trim piece that bridges the gap between the inner liner and the outer cabinet. It helps provide insulation and a finished appearance at the top of the freezer. Replace this strip if it is cracked, warped, or missing, which can allow cold air to escape and cause frost buildup.

Freezer not cooling or running warm? A failed evaporator fan motor stops cold air circulation. DIY-friendly repair typically takes 30-45 minutes.

The Door switch is an OEM replacement part for Frigidaire refrigerators. This part turns the light on/off as the door opens and closes.

Causes of a faulty door switch include normal wear of electrical contacts from repetitive on/off cycles. Moisture exposure may potentially corrode internal connections.

Symptoms of a bad light/switch include:

• The interior light fails to turn on when the door is opened
• The light stays on when the door is closed, leading to potential overheating
• An impact on the refrigerator’s temperature regulation due to the switch not signaling the door's closure

This Frigidaire OEM replacement part is also compatible with Electrolux, Gibson, Kelvinator, and some Kenmore models.

Light lens cover for refrigerator interior lighting. Replaces cracked, yellowed, or missing lens covers. Snaps into place over bulb compartment.

Powers your refrigerator's interior lighting. Replace when lights dim, flicker, or fail. Confirm fit with your model number before ordering.

Seals the evaporator cover to prevent air leaks, frost buildup, and temperature fluctuations. Replace if worn or cracked. Verify fit with your model.

Small spacer that corrects fit and leveling between freezer components. Replaces worn, missing, or damaged shims to restore proper alignment and clearance.

Supports and pivots your freezer door for smooth opening and closing. Replace when worn or bent to restore proper alignment, improve sealing, and prevent air leaks or frost buildup. Confirm fit by model number.

Secures door stop to hinge bracket, controlling opening angle. Replace if pin is bent, broken, or missing to restore smooth door operation.

Carries defrost water from your freezer drain outlet to the drip pan. Replace if cracked, kinked, or detached to prevent leaks onto floors and cabinets.

Collects defrost water beneath your freezer. Replace if cracked, broken, or missing to prevent leaks. Installs in the bottom compartment under the unit.

This drain pipe connects the defrost drain outlet to the drain pan area, channeling condensation and defrost water away from the freezer compartment. It is a rigid or semi-rigid tube that slides into the drain opening and directs water downward. Replace this part if you notice water pooling inside the freezer, ice buildup near the bottom of the compartment, or water leaking onto the floor beneath the appliance.

This small plastic clip secures the dishwasher drain hose to the pump assembly or discharge fitting, keeping the hose in place and helping prevent leaks or disconnection during operation. What it does:

• Holds the drain hose firmly to the pump or outlet fitting to maintain a watertight connection
• Prevents the hose from slipping free during drain cycles
• Helps stop water leaks and washing chamber flooding caused by a loose hose
• Useful when replacing a cracked or broken retaining clip

• One drain hose retaining clip

• Disconnect power and water supply before accessing the dishwasher lower access area
• Remove the access panel or kickplate to reach the drain hose and pump connection
• Use pliers or a flat tool to remove the old clip and snap the new clip over the hose/fitting until fully seated
• After installation, run a short drain cycle and inspect for leaks; re-secure if necessary

Cabinet corner trim piece for freezers. Covers and finishes the corner edge of the cabinet exterior. Replace if cracked, chipped, or missing.

Supports and pivots the freezer door at the top hinge point. Replace this hinge if cracked, broken, or worn to restore proper door alignment and swing.

Protective cover that snaps over your freezer's door hinge. Replace if cracked, broken, or missing to restore a finished look and shield the hinge.

Specs: Hex head ,1/4-20 x 5/8

Replace a cracked, broken, or missing interior shelf in your freezer. Restores stable storage space for organized food placement inside the cabinet.

Replacement glass shelf for refrigerator compartments. Installs on shelf frame to hold food and beverages. Replace if cracked, shattered, or broken.

Secures internal components and panels in your freezer. Replace this support bracket if it's cracked, broken, or missing to restore proper alignment.

If your freezer won't start, displays error codes, or buttons don't respond, this control board manages functions and cycles. Moderate DIY repair.

This replacement door bin mounts on the inside of your refrigerator door to hold bottles, jars, and condiments. Replacing a cracked or loose bin restores safe, usable storage and helps keep items organized and accessible.

• Provides storage on the door to keep bottles and jars upright
• Restores capacity when the original bin is cracked, warped, or missing
• Helps prevent items from tipping or falling when the door opens/closes
• Common symptoms: bin falls off, won't stay seated, or has broken tabs/cracks

What's included: 1 door bin Install notes:

• Remove all items from the old bin; lift straight up to release from the door slots
• Align the new bin's tabs with the slots and press down until fully seated
• Do not force; re-align if resistance is felt to avoid damaging the door liner
• Place in the correct door position for your model; some bins aren't interchangeable between levels

Basket handle for chest and upright freezers. Replaces broken, cracked, or missing handles that make it difficult to lift storage baskets in and out.

This is a mid-level wire or plastic storage basket that fits inside a chest or upright freezer to help organize frozen items. It slides or hangs inside the freezer compartment to keep food separated and accessible. Replace this basket if it is cracked, bent, has broken supports, or no longer sits securely in the freezer.

Secures hanging basket to freezer rack. Replaces broken, bent, or missing hanger to restore proper basket support and prevent sagging or detachment.

Fixes a loose or fallen wire basket inside your freezer. This support bracket secures hanging baskets in place for stable storage. Simple DIY repair.

Adjustable leveling foot installs at the bottom of your appliance to ensure stability and proper leveling. Replace if broken, cracked, or missing.

Replacement screw that secures freezer panels, brackets, and trim. Install when original hardware is missing, stripped, or loose to keep components aligned.

White toe grille panel for upright freezers. Mounts at base to cover components. Replace when cracked, discolored, or missing for a clean look.

Replacement screw that secures brackets, shelves, trim, panels, and covers inside your appliance. Install when the original is missing, stripped, or corroded.

Hex head screw that secures panels, brackets, and internal components in refrigerators and appliances. Replace when missing, stripped, or damaged.

Replacement mounting screw for freezer panels, trim, and brackets. Needed when original fastener is missing, stripped, or damaged during repairs.

Plastic bearing that acts as a pivot point for freezer door opening and closing. Replace if cracked, broken, or worn from repeated use over time.

This is a wire shelf designed to hang inside the freezer compartment, sometimes referred to as a pizza shelf due to its shape and placement. It provides additional flat storage space for frozen items. Replace it if the shelf is bent, rusted, or the mounting clips are broken, causing the shelf to sag or fall.

This is a small air baffle breather valve that helps equalize air pressure between the interior compartment and the outside environment. It allows air to pass through while helping maintain proper temperature regulation. Replace this valve if you notice excessive frost buildup, difficulty opening the door shortly after closing it, or unusual air pressure issues inside the unit.

Replaces cracked or broken mounting bracket in your freezer. Securely holds internal components in proper alignment. Needed when original is damaged.

Mounting bracket that secures freezer shelves and internal panels. Replace if cracked, bent, or broken to restore proper alignment and stability.

Guide rail that supports and directs refrigerator drawers along their track. Replace when original is worn, cracked, or broken to restore smooth sliding.

Replacement drawer slide for freezers. Restores smooth gliding when original is broken, worn, or causes sticking. Essential for proper drawer alignment.

Supports and guides the crisper drawer for smooth sliding. Replace if cracked, broken from stress, or if drawer no longer sits securely in refrigerator.

Green plastic handle for freezer storage baskets. Replaces cracked, broken, or missing handles on sliding baskets. Direct fit replacement part.

Rubber grommet for freezer interior assembly. Replaces worn, cracked, or missing grommets that secure components or reduce vibration in your unit.

Replace your broken or missing freezer basket handle. This handle attaches to wire storage baskets, providing a grip for lifting and organizing items.

Retaining clip for freezer interior components. Secures shelves, bins, or trim pieces in place. Replace if cracked, broken, or missing to restore fit.

Adhesive-backed plastic clip secures wires and small hoses inside your freezer or refrigerator. Replace when loose or damaged to reduce rattling. Confirm fit with your model number before ordering.

Rubber grommet cushions and seals freezer components, reducing vibration and preventing wear where wiring or rods pass through. Replace if cracked or worn.