Parts for Ge GFWS2505F0RR: Cabinet (1) Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

A replacement 10-16 shoulder screw (Type A) used to secure appliance components where a shoulder/clearance is required. Restores proper alignment and fastening for panels, brackets, or assemblies that use a shoulder-style fastener. What it does:

• Provides a fixed shoulder to control depth and spacing between parts
• Secures panels, brackets, or moving parts while allowing an exact clearance
• Helps prevent over-driving and protects mating parts from damage
• Commonly used where precise alignment or rotation clearance is needed

• Inspect the mating hole and threads for damage before installing
• Use the correct driver and torque—do not over-tighten to avoid stripping
• Replace with the same screw type and size to maintain proper fit and clearance
• Disconnect power and follow all safety precautions when accessing internal components

Fix washer not filling, slow fill, wrong temperature, or overfilling. This inlet valve controls hot and cold water flow into your tub during each cycle.

If your washer vibrates excessively or makes loud banging noises during spin, a worn suspension spring may be the cause. Supports the tub and dampens movement.

Replace your washer's support spring if it's broken, stretched, or missing. This suspension component helps stabilize the drum during operation.

Retaining clip for washer assemblies. Secures components in place during operation. Replace if clip is broken, missing, or no longer holds parts firmly.

This guide pin bushing cushions and aligns a rotating guide pin, helping the appliance drum or assembly run smoothly and quietly. Replaces worn bushings to reduce noise and prevent pin-to-housing wear. What it does

• Provides a low-friction bearing surface for a guide pin or shaft.
• Keeps the pin centered to prevent wobble and misalignment during operation.
• Reduces noise and metal-on-metal wear caused by a worn or damaged bushing.
• Helps maintain proper movement of the drum/assembly for consistent performance.

• One guide pin bushing.

• Disconnect power before beginning any repair to avoid shock or injury.
• Access may require removing panels, the drum or related assemblies; follow service manual steps.
• Inspect surrounding parts (pin, housing, clips) and replace any damaged components.
• Use appropriate tools and avoid forcing the bushing into place; follow the OEM service instructions for torque/spec guidance.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Air vent tube for washer dispenser assembly. Replace if cracked, broken, or leaking. Connects to dispenser body with O-ring seal. Requires panel removal.

This rotor position sensor (RPS) module monitors the washer's drive motor position and speed and reports it to the control. Replacing a failing sensor helps restore smooth agitation and dependable spin, reducing stalls and early cycle stops.

• Detects the motor rotor's position/speed so the control can start, reverse, and ramp the motor correctly
• Typical symptoms include no spin or agitation, motor starts then stops, or the cycle ends early
• Causes intermittent/erratic motor movement; lid locks but the tub doesn't move
• Use when diagnostics indicate an RPS/speed-sensor or motor feedback fault

• Disconnect power and turn off water before servicing
• Access the motor area; photograph wiring before disconnecting
• Align the sensor correctly and fully seat the harness connector—do not force pins
• Run applicable diagnostics/calibration after installation to ensure proper spin and agitation

This rear bottom panel replaces the lower back cabinet section to protect internal components and restore structural support. It helps reduce drafts, debris entry, and rattling from a damaged or corroded lower rear panel. What it does:

• Covers and protects compressor, wiring and other rear-located components from debris and accidental contact
• Restores cabinet rigidity and helps prevent gaps that can cause vibration or rattling
• Helps maintain proper airflow routing at the appliance rear when original panel is missing or bent
• Useful when the original panel is cracked, rusted, dented, or warped

• One rear bottom panel only

• Install with the original screws or fasteners;
• Disconnect power and any water supply before accessing the rear cabinet
• Handle edges carefully; wear gloves to avoid cuts from sheet metal
• If corrosion or other damage extends to mounting points, inspect and repair the cabinet structure before installing

Replace missing or stripped mounting screws in your washer dryer combo. This 12-pack secures panels, components, and internal parts during assembly or repair.

Fix washer agitation issues with this rotor assembly. Transfers motor torque for proper wash action. Common fix for washers that won't agitate correctly.

5/16-24 hex washer head screw for washers. Secures internal panels and mounting brackets. Order a replacement if the original is stripped, missing, or damaged during disassembly.

Hex head screw for washer assembly. Secures internal components and panels. Replace if stripped, rusted, missing, or damaged during repair work.

Fix a washer that won't spin or agitate properly with this stator assembly. Direct motor component replacement requires moderate skill and basic tools.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.