Parts for Whirlpool EB22DKXFW01: 01 - Cabinet Parts

Black plastic plug that covers exposed mounting holes in refrigerator door handles. Snap-in design fills gaps for a finished look and keeps out debris.

White button plug cap for refrigerators. Covers screw holes or mounting points on control panels and exterior surfaces. Replace when missing, cracked, or discolored.

Black plastic plug that covers exposed mounting holes in refrigerator door handles. Snap-in design fills gaps for a finished look and keeps out debris.

White button plug cap for refrigerators. Covers screw holes or mounting points on control panels and exterior surfaces. Replace when missing, cracked, or discolored.

Comes complete with the front lever assembly, roller, shaft rivet, bracket and nut. For roller only use WP10450603

A small replacement clip-style retainer that secures the appliance toe grille to the cabinet, keeping the grille flush and in place. Replaces worn or broken clips to restore proper fit and appearance. What it does:

• Secures the toe/grille panel to the appliance cabinet so the grille stays aligned and snug
• Stops the grille from sagging, rattling, or popping off during use
• Fits into designated mounting slots or tabs to lock the grille in place
• Commonly replaced when clips are cracked, missing, or loose

• Disconnect power to the appliance before servicing to avoid shock or injury
• Access the toe grille by removing any screws or releasing retaining tabs per your model's service instructions
• Press the clip into the grille/cabinet mounting slot until it snaps in place; verify the grille seats evenly
• If multiple clips are damaged, replace all needed clips for a secure fit

Center hinge pin that secures the refrigerator door at the pivot point. Replace if your original pin is worn, bent, or missing to restore alignment.

A non-metal shim used to stabilize and level your appliance for quieter, more reliable operation. Simple, low-profile support that helps correct minor height and balance issues so doors and drawers align and appliances sit securely. What it does:

• Adds thin, non-metallic spacing under feet or frame to correct slight height differences
• Helps stop rocking or tipping that can cause noise, vibration, or misaligned doors
• Supports even weight distribution to reduce uneven wear on adjustable legs
• Useful when adjusting leveling feet can't fully correct a gap or tilt

• Place shim under the appliance foot or frame where additional height or support is needed
• Re-check appliance level and stability after installing; add/remove shims as required
• Use with care to avoid creating instability; pair with proper leveling adjustments

Nonmetal shim spaces and cushions refrigerator components to improve alignment and reduce vibration. Replace when worn to restore quiet operation.

Mounting screw for refrigerator assembly. Secures components and panels in place. Replace if screw is stripped, missing, or no longer holding tight.

This hex washer-head screw secures panels, brackets, and other components inside your appliance. Replacing a worn, stripped, or missing screw restores a tight fit, reduces vibration and rattles, and helps keep assemblies properly aligned.

• Fastens panels, brackets, covers, and internal hardware to the cabinet or frame
• Helps prevent loosening, rattling, or misalignment during appliance operation
• Replace if the head is rounded, threads are stripped, or the screw is missing
• Useful after service when an original fastener is lost or damaged

• Disconnect power and shut off gas/water before starting
• Use the correct nut driver or socket for the hex head to avoid rounding
• Start threads by hand to prevent cross-threading; tighten snugly without overtightening

Panel fastener screw for refrigerators and freezers. Secures cabinet panels, trim, and components. Replace if missing, stripped, or damaged.

Replacement bottom hinge pin for refrigerator doors. Restores proper door pivot and alignment when original pin is worn, bent, or missing during moves.

Color: Black

This is a replacement screw designed to work with a wide range of household appliances. It is used for many purposes in these appliances, from holding body panels together to securing electronics into control boards. However, screws are subject to damage through corrosion, impact, and improper installation/removal. In most cases, the primary damage to this screw is through corrosion – it may become rusted or corroded in place, depending on the appliance and the maintenance provided during its lifespan. The screw may also be stripped or rounded due to improper removal or installation. If the screw is damaged, lost, or corroded in place, it will need to be replaced. In most cases, removal will require nothing more than a Phillips head screwdriver or the appropriately sized socket with a ratchet. However, if the screw is damaged, it may require a tap set to remove it from its mounting location. Note that this is a genuine OEM replacement screw made from durable, high-quality metal, and is sold individually. It fits Whirlpool, Maytag, Roper, Estate, Amana, Crosley, and Thermador appliances. It is used in over 150 machines, ranging from washers and dryers to air conditioners.

Ice maker not making ice or water leaking? A faulty water inlet valve often causes these issues. This DIY fix takes 5-15 minutes with basic tools.

Secures panels and components in place. Replace this fastener if stripped, corroded, or missing to restore proper alignment and eliminate rattling.

Adjustable leveling foot that supports and stabilizes your refrigerator. Replace if worn, broken, or missing to eliminate wobbling and vibration.