Parts for QFT15ESSN0WW: Cabinet & Top Panel Parts

These front panel screws secure the appliance's front panel to the chassis, restoring proper fit and appearance. Replace stripped or missing screws to stop panel rattling and uneven gaps. What it does:

• Fastens the front panel to the appliance frame for a secure fit
• Prevents panel vibration, rattling, and misalignment during operation
• Replaces corroded, stripped, or lost fasteners that keep the panel loose
• Helps maintain proper access to controls and internal components

• Front panel screws

• Disconnect power before servicing to avoid electrical shock
• Use the correct size screwdriver to avoid stripping screw heads
• Thread screws in by hand first, then tighten snugly—do not overtighten
• Keep removed hardware organized for reassembly

This is a ST3.5 x 12 self-tapping screw designed to secure trim, panels, and small appliance components. It replaces stripped or missing screws to restore proper fit and reduce movement or vibration. What it does:

• Fastens appliance panels, brackets, or trim where ST3.5 x 12 screws are specified
• Helps stop rattling, loose panels, or parts that shift during operation
• Provides a secure threaded hold in thin sheet metal or plastic mounting points
• Matches OEM fit where the WH02X26267 screw is specified

• Use the properly sized Phillips driver to avoid cam-out and head damage
• Start screws straight and apply steady pressure; do not over-torque to prevent stripping
• Wear eye protection when working with small fasteners and sharp edges
• Compare size and thread to ensure a proper match

This tapping screw is a self-tapping fastener used to secure panels and components on compatible appliances, restoring secure mounting and preventing loose or vibrating parts. It's a direct replacement for a single factory screw. What it does:

• Threads into sheet metal or plastic mounting points to hold panels, brackets, or small components
• Replaces missing or stripped screws that cause loose panels or rattling
• Helps restore proper alignment and secure connections for controls and covers
• Works where a self-tapping fastener is required instead of a machine screw

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid cam-out and head damage
• Start threading by hand to ensure proper engagement, then tighten until snug — do not over-torque
• Replace only with the exact part to ensure fit and proper fastening

The Control Board is an OEM part for GE dryers. As the central electronics module, it regulates all dryer functions and operations during cycles. The control board receives input from temperature sensors and buttons to distribute power accordingly.

Causes of a bad control board can include normal wear over time, water damage, electrical faults that arise with many uses, or physical impacts. Prolonged exposure to high heat cycles can sometimes lead to component failures or short circuits that disrupt proper functioning.

Symptoms of a bad control board include: 

• The dryer failing to start or operating unpredictably  
• Display/button malfunctions where settings cannot be accessed
• Inability to progress fully through cycles
• Erratic stopping, hanging, or inconsistent behaviors

This OEM GE replacement control board restores full and intended operation to the dryer. This part is compatible with some Hotpoint, RCA, and select Kenmore dryer models.

This water reservoir tank stores and supplies water to the dispenser/ice system, restoring normal water flow and ice production. Designed to match OEM fit, it replaces a cracked, leaking or empty reservoir to stop leaks and filling problems. What it does

• Holds and channels water to the dispenser and/or ice-making components.
• Restores proper water supply when a cracked or damaged tank causes leaks.
• Helps resolve slow or no-fill symptoms with the ice maker or dispenser.
• Maintains sealed water routing to prevent internal leaks and water damage.

• Disconnect power and turn off the water supply before starting.
• Drain remaining water from the system to avoid spills.
• Handle and seat the tank carefully to avoid cracks; use OEM fasteners and gaskets if applicable.

This terminal block cover encloses the dryer's rear power-cord connection. Replacing a missing or damaged cover keeps wiring protected and helps prevent accidental contact with the terminals.

• Covers and shields the terminal block and cord connections at the back of the dryer
• Helps keep dust, debris, and fingers away from live electrical terminals
• Restores proper enclosure when the original cover is broken, warped, or missing
• Common symptoms: missing/broken cover, exposed connections, cover will not stay secured

• Disconnect power by unplugging the dryer or switching off the circuit breaker
• Access the rear of the unit; remove the old cover and retain hardware if reusable
• Position the new cover over the terminal block and secure with the appropriate fasteners per the product manual
• Ensure cord strain relief and connections are properly secured before restoring power

This metal drum ground strap provides a secure electrical connection between the dryer drum and chassis to maintain proper grounding and reduce the risk of static or electrical faults. It's a simple, durable part used on many electric dryers. What it does:

• Bonds the rotating dryer drum to the appliance frame to maintain electrical continuity
• Helps prevent static buildup and reduces the chance of stray voltage on the drum
• Supports safe operation by providing a path to ground for residual current
• Often checked when diagnosing intermittent shocks, arcing, or grounding-related noise

• One metal drum ground strap

• Disconnect power before inspecting or replacing this part to avoid electrical shock
• Replacement is typically accessed from the front or rear panel;
• Use the same mounting hardware and orientation as the original; secure all fasteners tightly
• If signs of burning, heavy corrosion, or damaged insulation are present, inspect surrounding components and wiring

This Heater Assembly is an OEM part for GE dryers. It plays a pivotal role in the heating system of the dryer, responsible for generating the heat required to dry clothes efficiently. 

The deterioration of a heater assembly can be attributed to factors like extended usage, electrical issues, or a buildup of lint and debris, which can impede its functionality. A malfunctioning heater assembly can significantly affect the drying process.

Symptoms of a failing Heater Assembly include:

• The dryer not heating up adequately or at all.
• Longer drying times than usual.
• The dryer repeatedly shuts off during a cycle.
• Inconsistent heating leads to partially dried clothes.
• Increased energy consumption due to inefficiency.

This GE OEM replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

A small mounting clip that secures trim, panels, or wiring harnesses to appliance frames to restore proper fit and reduce rattles. Replaces a lost or broken retainer so parts stay aligned and stable during use. What it does

• Secures plastic trim, panels, or wire harnesses to the appliance frame to prevent shifting or sagging
• Stops rattling or vibration caused by loose panels or components
• Helps maintain proper alignment of parts for reliable operation
• Simple plastic/metal retainer used wherever a small fastener clip is required

• Disconnect power to the appliance before attempting any repair to avoid electrical shock
• Access the area by removing the minimal surrounding trim or panels as needed
• Press or snap the clip into the matching slot or stud until it locks; replace any damaged mating hardware

This condenser housing drain tube routes defrost and condenser water away from the condenser area to the drain pan, preventing leaks and water buildup under the refrigerator. It restores proper drainage and reduces corrosion risk. What it does:

• Channels meltwater from the condenser housing to the drain pan to prevent pooling beneath the fridge.
• Helps stop water leaks, floor puddles, and related odors caused by standing water.
• Ensures proper condensate flow after defrost cycles and normal operation.
• Fits into the condenser housing and connects to the drain path to maintain intended drainage.

• One condenser housing drain tube.

• Disconnect power to the appliance before starting any work.
• Access typically requires removing the lower grille or toe kick and pulling the unit away from the wall.
• Inspect surrounding clips and seals; replace any damaged fasteners to ensure correct routing and a secure fit.
• After installation, run a short manual defrost or pour a small amount of warm water to ensure the new tube drains properly.

This condenser tank overflow tube directs excess condensation away from the condenser tank to prevent pooling and potential water damage. It restores the refrigerator's drainage path for cleaner, drier operation. What it does:

• Funnels overflow or excess condensate from the condenser tank to the drain path
• Helps stop water from collecting under or around the condenser area
• Addresses symptoms like puddling under the fridge, water on the floor, or visible leaks near the condenser
• Works with the refrigerator's existing drain system to maintain normal condensation flow

• One condenser tank overflow tube

• Unplug the appliance or disconnect power before servicing
• Remove required access panels to reach the condenser tank/drain area per manufacturer instructions
• Secure tubing without kinking or over-bending

This top panel guide pin screw secures the appliance top panel and keeps the panel aligned during use. It replaces a missing or damaged guide screw to reduce panel movement and rattling. What it does:

• Secures the top panel to the chassis so the panel stays aligned
• Prevents the top panel from shifting, vibrating, or rubbing during operation
• Restores proper fit after a stripped, lost, or damaged screw

• Disconnect power to the appliance before starting any repair
• Remove the top panel or access panel to reach the guide pin location
• Install by hand to align, then tighten snugly with the appropriate screwdriver; avoid over-tightening to prevent strip-out
• If threads are damaged, inspect the mounting hole and replace or repair the threaded insert as needed

This humidity sensor and harness assembly detects moisture levels inside the appliance and delivers reliable signal feedback to the control board so the appliance can regulate humidity-sensitive functions and preserve stored items. What it does:

• Senses interior humidity and sends signal to the control module for proper humidity management
• Helps the appliance maintain fresher conditions in humidity-controlled compartments
• Commonly replaced when humidity-related controls stop responding or readouts are inconsistent
• Works as the electrical interface between the sensor element and the main wiring harness

• One humidity sensor with attached harness assembly

• Disconnect power to the appliance before starting any repair to avoid electric shock
• Handle the sensor and connector carefully to avoid bending pins or damaging the harness
• Verify connector orientation and secure clip engagement; route the harness away from moving parts
• Test the control board and related dampers/actuators if symptoms persist after replacement.

This rear bearing supports the dryer drum shaft and helps the drum turn smoothly. Replacing a worn bearing restores quiet operation and prevents drum wobble or metal-on-metal noise for reliable drying performance. What it does:

• Supports the drum rear shaft to maintain proper drum alignment and rotation
• Reduces squealing, grinding, or rumbling noises caused by worn bearing surfaces
• Prevents excessive drum wobble or rubbing that can damage the drum or cabinet
• Helps the drum turn smoothly for consistent drying and reduced wear on the motor

• One rear bearing

• Disconnect power to the dryer before starting any repair; electricity and moving parts are hazardous
• Access requires removing the dryer cabinet and drum; keep track of fasteners and alignments
• Inspect drum shaft, front support, and seals while replacing the bearing; replace related worn parts as needed
• Test the dryer with the cabinet open after installation to ensure smooth rotation before reassembling

This ground screw secures an appliance's chassis grounding connection to ensure a reliable electrical ground and help reduce the risk of shock or electrical faults. Simple replacement when the original screw is missing, damaged, or corroded. What it does:

• Fastens the appliance ground wire or grounding strap to the metal chassis for a secure electrical ground.
• Restores a proper grounding point when the original screw is loose, stripped, corroded, or missing.
• Helps address symptoms related to poor grounding, such as intermittent power, electrical noise, or tripped breakers (as reported).
• Provides a direct, stable connection that supports safe appliance operation.

• One ground screw

• Disconnect power to the appliance before attempting any repairs to avoid electrical shock.
• Tighten to snug contact with the chassis; avoid overtightening which can strip threads or damage the metal.
• If ground wire or chassis threads are damaged, inspect for necessary additional parts or repair.

The Frontload Stack Kit is an OEM part for GE front-loading washers and dryers. This comprehensive kit contains all the mounting rails, brackets, and hardware required to vertically stack these high-efficiency appliances for a sleek, built-in appearance. 

Causes of a bad stack kit can include wear and tear over time, impact damage, or compromised fittings that result in loose connections or stability issues.

Symptoms of a bad stack kit include:

• Excessive noise and vibration during use  
• The appliances rocking or tilting noticeably while in operation
• Visible movement or play between the stacked units
• Mounting rails or connections that feel loose or unstable

This OEM GE replacement stack kit is also compatible with Hotpoint, RCA, Profile, and some Kenmore front-loading washer and dryer models. As always, check fitment specifications before ordering and follow installation instructions carefully for safe operation.

The Fuse for Dryer is an OEM replacement part for GE electric dryers. The fuse acts as a safety shut-off mechanism, protecting the dryer's electrical components from power surges or overloading. It plays a critical role in circuit protection.

Causes of a blown fuse can include power fluctuations, overloading due to wet/heavy loads, or underlying electrical component issues in the dryer. The fuse shields expensive components like motors, heating elements, and electronic boards.

Symptoms of a blown fuse include:

• The dryer not powering on at all  
• Cycles not completing or functionality issues mid-cycle
• Safety features like the timer not working properly

This GE replacement fuse helps maintain circuit integrity and safety. It prevents potential fires from damaged wiring or short circuits. Genuine OEM quality ensures form and fit compatibility with your existing fuse clips for seamless installation.

This GE replacement part is compatible with Hotpoint, RCA, and Kenmore dryer models. 

This RJ45 connector is the modular network jack used to connect Ethernet-style cords to the appliance's control/communication board, restoring a secure data link for diagnostics or network features. Fits the factory wiring interface. What it does:

• Provides a secure Ethernet-style connection between an external cable and the appliance control/communication board.
• Restores reliable network or communication connectivity when the original jack is cracked, loose, or fails.
• Helps resolve symptoms such as intermittent or no network/communication link and visibly damaged or bent connector pins.
• Serves as the replacement interface for diagnostics ports or board-mounted network connections.

• One RJ45 connector (modular jack) as pictured.

• Disconnect power to the appliance before beginning any repair to avoid electric shock.
• Access the control or communication board per your appliance's service instructions; handle PC boards by the edges to avoid damage.
• Use proper tools to remove the old connector and secure the replacement; ensure mating cable seats fully and pins align.
• After installation, restore power and test the connection and any affected network/communication features.