Parts for QFT15ESSN0WW: Drum Parts

A small replacement housing screw that secures appliance panels and brackets, restoring proper fit and preventing rattles or loose panels. Fits common appliance housings where a short ST4 x 12 self-tapping screw is required. What it does:

• Fastens housing panels, trim, or internal brackets to maintain proper alignment and reduce vibration
• Replaces missing or damaged screws that cause loose or rattling panels
• Works with sheet metal and plastic mounting points designed for ST4 thread size
• Small, low-profile head designed for appliance interiors

• One housing screw (ST4 x 12)

• Disconnect power before servicing the appliance and work on cool surfaces
• Use the correct screwdriver or bit to avoid stripping the head
• Install gently and avoid overtightening to prevent thread or panel damage

This tapping screw is a self-tapping fastener used to secure panels and components on compatible appliances, restoring secure mounting and preventing loose or vibrating parts. It's a direct replacement for a single factory screw. What it does:

• Threads into sheet metal or plastic mounting points to hold panels, brackets, or small components
• Replaces missing or stripped screws that cause loose panels or rattling
• Helps restore proper alignment and secure connections for controls and covers
• Works where a self-tapping fastener is required instead of a machine screw

• Disconnect power to the appliance before beginning any repair
• Use the correct screwdriver or bit to avoid cam-out and head damage
• Start threading by hand to ensure proper engagement, then tighten until snug — do not over-torque
• Replace only with the exact part to ensure fit and proper fastening

The Outlet Thermistor is an OEM component specifically designed for GE laundry machines. It is a heat-sensing component located near the dryer outlet that monitors exhaust air temperatures during the drying cycle. The thermistor plays a crucial role in appliance safety by regulating heat levels.

Symptoms of a bad outlet thermister include: 

• Inability to achieve necessary air temperatures for effective drying
• Dryer fails to sense when clothes are dry and turns off prematurely  
• Fault codes or error messages displayed relating to temperature issues

Causes of failure are typically related to sensor degradation or internal electrical faults over many uses. Proper airflow is also necessary for accurate temperature readings.

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.
 

This lamp lens gasket is the rubber seal that fits around the light lens to cushion and seal the lens assembly, helping keep the light secure and reducing dirt, grease and vibration that can affect visibility. What it does:

• Cushions and centers the light lens to prevent rattling or movement
• Helps block grease, dust and moisture from reaching the lamp housing
• Maintains a snug fit for the lens to support consistent light output
• Reduces the chance of lens contact that could cause cracking or wear

• Disconnect power to the appliance before starting any work.
• Remove the lens or lens holder carefully to avoid breaking the lens; keep all fasteners.
• Fit the gasket into the lens recess and press the lens evenly into place for a proper seal.

The Lint Filter is an OEM part for GE dryers. This part is responsible for capturing lint and debris from your laundry during the drying cycle, preventing it from clogging the dryer vent and ensuring optimal airflow. The lint filter traps lint particles, lint, and other debris, preventing potential fire hazards associated with lint buildup.

A bad lint filter can occur due to wear and tear, damage, or blockage. If you notice symptoms such as longer drying times, reduced airflow, or visible lint accumulation in your dryer, it may be time to replace the filter.

Symptoms of a bad lint filter include:

• Longer drying times
• Reduced airflow
• Visible lint accumulation in the dryer

Ensure the efficient and safe operation of your GE dryer by replacing the faulty lint filter with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances. 
 

A small hex nut used to secure fasteners on appliances, restoring proper thread engagement and helping hold panels or components in place. Replaces a worn or missing nut to prevent loose or rattling parts. What it does:

• Secures a mating bolt or stud to keep panels, trim, or components fastened
• Restores proper thread engagement when an original nut is stripped or lost
• Helps stop vibration-related looseness and rattling noises
• Suitable wherever the OEM called out this specific nut in the parts list

• Turn off and unplug the appliance before accessing internal components
• Use the correct size wrench or socket to avoid rounding the nut
• Replace with the same style and thread engagement length specified by the OEM
• Replace the mating stud or bolt to ensure a secure fit

This door seal restores a tight barrier around the dryer door opening. By preventing air leaks and lint escape at the door, it helps maintain stable heat and airflow for reliable drying performance.

• Seals the gap between the door and front panel to keep heated air inside the drum
• Helps reduce moisture and lint escaping around the door area
• Can help with symptoms like long dry times, feeling warm air leaking near the door, or a visibly torn/flattened seal
• Provides cushioning so the door closes evenly and quietly

• Disconnect power before servicing; shut off gas supply if applicable
• Open the door, remove the old seal, and clean any residue from the mating surface
• Fit the new seal evenly around the opening; seat it fully per your model's retention method
• Close the door to verify uniform contact all around before running the dryer

The Belt is an OEM part for GE dryers. This part is responsible for transferring power from the dryer's motor to the drum, enabling it to rotate and tumble your clothes during the drying cycle.

A bad drum drive belt can occur due to wear and tear, stretching, or snapping. If you notice symptoms such as the drum not spinning, unusual noises during operation, or clothes not drying properly, it may be time to replace this belt.

Symptoms of a bad drum drive belt include:

• Drum not spinning
• Unusual noises during operation
• Clothes not drying properly

Restore your GE dryer by replacing the faulty drum drive belt with this genuine OEM part.

This GE part can also be used on Hotpoint, RCA, and Kenmore/Sears appliances.