Parts for Electrolux ELFW7637BW0: Cabinet / Top Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Washer won't start, stops mid-cycle, or shows error codes? This motor control board regulates drum speed and cycle functions. Moderate difficulty repair.

Replacement mounting screw for dryers. Secures panels, brackets, and internal components. Order if your original screw is stripped, missing, or damaged.

This cover fits over the door lock flange area on the front of the washing machine. It provides a finished appearance and protects the door lock mechanism from debris and moisture. Replace this cover if it is cracked, broken, or missing, which can leave the door lock assembly exposed and vulnerable to damage.

Washer door won't lock or stay closed? This door lock secures your front-load washer during cycles. DIY repair takes 5-10 minutes with basic tools.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

Replacement mounting screw for dryers. Secures panels, brackets, and internal components. Replace if stripped, missing, or corroded during repairs.

This is the inner glass for an oven door that restores a clear view of the oven cavity and helps the door seal properly. Replacing damaged or cracked inner glass improves visibility and helps maintain oven temperature. What it does:

• Replaces cracked, chipped or spiderwebbed inner oven door glass
• Restores a clear viewing window so you can monitor cooking without opening the door
• Helps maintain the oven's internal temperature by restoring the door's barrier
• Stops rattling or vibration caused by loose or broken glass pieces

• Allow the oven to cool and disconnect power before starting; glass can be sharp—wear cut-resistant gloves and eye protection
• Some models require partial door disassembly (hinges/retainers) to remove and install the inner glass—keep screws and small parts organized
• Handle glass carefully to avoid damage; do not overtighten fasteners which can crack the glass
• Follow OEM instructions or a model-specific repair guide for proper reassembly and safety checks

Broken door latch preventing your washer from starting? This door latch secures and locks the door during cycles. DIY repair takes under 10 minutes.

Washer door hinge assembly that supports and allows the door to open and close smoothly. Replace if hinge is cracked, broken, or no longer securely mounts.

Replacement mounting screw for dryers. Secures panels and internal components. Needed when original screw is stripped, damaged, missing, or causing loose parts.

Secures the front panel to your washer frame. Replace this clip if your panel is loose, rattling, or won't stay in place due to a broken or missing clip.

Replacement mounting screw that secures panels, brackets or small components in compatible appliances. Installs quickly to replace stripped or missing fasteners and help stop rattling and restore proper alignment. What it does:

• Fastens panels, trim pieces, brackets and other small assemblies to the appliance.
• Replaces stripped, corroded or broken screws that can cause loose parts or vibration noise.
• Helps restore proper alignment of doors, drawers or trim when a missing screw allows movement.
• Small appliance fastener sized for original mounting points—use the OEM screw whenever possible.

• Disconnect power and water before starting any repair.
• Start the screw by hand to avoid cross-threading; use the correct screwdriver or bit.
• Tighten snugly but avoid overtightening to prevent stripped threads or damaged plastic.

Replacement mounting screw for washers and laundry centers. Secures internal components and panels. Order a new screw if original is lost or stripped.

Replace your washer's control panel if cracked, damaged, or worn. This panel houses the controls and display on the front of your washing machine.

This is a titanium-colored side panel for a washing machine. It attaches to the side of the washer cabinet to enclose and protect the internal components. Replace this panel if it is dented, rusted, cracked, or damaged during a move or installation.

This metal top panel replaces the upper rear control housing on compatible Frigidaire ranges and stoves, restoring a secure mounting surface for controls and improving cabinet fit and appearance. Ideal for repairing bent, rusted, or damaged panels. What it does

• Replaces the upper rear housing that supports control knobs, switches and the backguard area
• Restores proper alignment and spacing between the cooktop and rear controls
• Stops light leaks and relieves stress from warped or bent panels
• Commonly used when the panel is dented, rusted, cracked, or has broken mounting tabs

• One top panel

• Disconnect power (and gas, if applicable) before starting any work
• Handle sharp sheet-metal edges with gloves; panel edges can be sharp
• Remove control knobs, backguard, or trim as required and save screws for reinstallation
• Align mounting tabs and secure with original hardware; test controls after reassembly

This top panel in white restores the oven/stove's upper exterior, improving appearance and protecting internal components from spills and debris. It's a direct-replacement exterior shell piece designed to match original fit and finish. What it does:

• Replaces a cracked, warped, dented, or discolored upper cabinet panel
• Protects control housing and internal components from grease, spills, and dust
• Restores a flush, finished look to the appliance top and backguard area
• Helps maintain proper alignment for control and trim pieces

• Disconnect power to the appliance before beginning any work
• Typical removal requires removing screws and lifting the old panel straight out; keep mounting hardware
• Handle edges carefully to avoid cuts and protect the painted finish during installation

Replacement base for front-load washers. Provides structural support and stability. Order this part if your original base is cracked, broken, or missing.

This is a protective cover that shields the door lock mechanism on a washing machine. It helps prevent moisture, debris, and damage from reaching the door lock assembly. Replace this cover if it is cracked, broken, or missing, which could leave the door lock exposed and lead to premature lock failure or error codes.

The washer front panel forms the outer cabinet exterior, housing the control panel and door. Replace if cracked, dented, warped, or damaged from impact.

Replace cracked or warped washer control panel trim. Restores finished appearance and protects internal switch assembly. Straightforward installation.

Washer won't power on or turn on? A faulty power cord with frayed wires or damaged plug may be the cause. Direct electrical connection replacement.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This bushing protects the appliance service cord where it passes through the cabinet, reducing wear and preventing chafing that can expose wiring. It's a simple replacement that restores a safe cord entry point. What it does:

• Cushions and centers the service cord at the cabinet opening to prevent abrasion
• Helps keep the cord from rubbing on sharp metal edges that can cause insulation damage
• Reduces risk of shorting, sparking, or intermittent power caused by a worn cord
• Commonly replaced when the existing bushing is cracked, missing, or deformed

• One service cord bushing

• Disconnect power (unplug or switch off breaker) before servicing
• Inspect the cord and surrounding insulation; replace the cord if damage is found
• Push the bushing into the cabinet opening, then route the cord through the bushing until seated
• Reuse only if undamaged; do not force a damaged bushing into place

Adjustable leveling leg for washers. Securely holds machine in place while allowing height adjustment on uneven floors. Replace if stripped or seized.

Suspension spring for front-load washers. Supports the drum and absorbs vibration during spin cycles. Replace if broken, detached, or stretched out.

This replacement refrigerator door magnet helps the door stay tightly closed so the appliance maintains proper temperature and efficiency. It restores the magnetic seal that keeps cold air in and warm air out. What it does:

• Replaces a worn or broken door magnet to improve door sealing and reduce temperature loss
• Helps stop frequent compressor cycles caused by a poor seal
• Can reduce frost buildup and prevent food spoilage related to a leaking seal
• Works with the door gasket to maintain proper closing force

• Disconnect power to the appliance before starting any repair
• Clean the magnet channel and surrounding area so the magnet seats properly
• Press or slide the magnet into place; some applications use clips or adhesive—verify fit before final installation

Replacement control panel button for front-load washers. Installs on the console to restore operation when original button is cracked, broken, or missing.

Mounting bracket for front-load washers. Secures internal components in place. Replace if bracket is cracked, bent, broken, or missing hardware slots.

Suspension spring bushing absorbs vibrations and stabilizes the washer tub during operation. Replace if experiencing excessive noise or movement. Verify fit.

Sound dampening insulation that reduces vibration and noise in your washer. Replace if worn, torn, or missing to restore quiet operation and protect components.

Pan head mounting screw for dryers. Secures internal components and panels. Replace if stripped, missing, or damaged during appliance maintenance.

Replacement mounting screw that secures panels, brackets, and trim pieces on your washer. Needed when original fasteners are missing, stripped, or damaged.

This metal mounting bracket secures an internal appliance component to the cabinet or frame, restoring proper alignment and preventing vibration. Use this replacement to stabilize loose parts and reduce noise or movement. What it does

• Provides a stable attachment point to hold internal components in place
• Helps stop rattling, vibration, or shifting caused by a broken or bent mount
• Restores correct alignment so connected parts operate smoothly
• Works where a small structural support or fastener anchor is required

• Disconnect power and water before beginning any repair
• Use common hand tools; retain and reuse original fasteners unless damaged
• Handle edges carefully; wear gloves and eye protection when needed
• Verify proper alignment and torque of mounting screws during reassembly

Replace a worn, broken, or missing washer cabinet damper to restore smooth counterweight action and controlled movement. Installs on cabinet assembly.

Replace your washer's water deflector if it's cracked, broken, or missing. This part mounts inside the drum to guide water flow during wash cycles.

Wire harness for front-load washers. Connects electrical components to the control board. Replace if wires are frayed, connectors damaged, or broken.

Fix intermittent power issues, control failures, or non-functioning components in your washer. This wiring harness assembly restores electrical connections.

Secures and organizes wires inside your appliance. Replace if broken, loose, or missing to prevent wire damage. Verify fit with your model number.

Mounting screw for washer cabinet and component assembly. Replace if screw is stripped, missing, or damaged during disassembly. Essential hardware piece.

Plastic hole plug for washer cabinet or panel. Covers unused mounting holes or ports. Replace if cracked, missing, or broken to maintain a finished look.

This door gasket is the flexible seal that fits around a refrigerator/freezer door to help keep cold air inside and warm air out, preserving temperature control and reducing energy loss. What it does:

• Seals the door perimeter to maintain proper interior temperature and efficiency
• Helps prevent moisture and warm air from entering the cabinet, reducing frost buildup
• Stops food spoilage and compressor overwork caused by a damaged or loose seal
• Symptoms of a failing gasket: visible gaps, torn or brittle rubber, condensation or frost inside the compartment, or higher-than-normal temperatures

• Disconnect power to the appliance before starting any work
• Remove the old gasket and clean the door channel before installing the new seal
• Align the gasket evenly around the door and press it fully into the channel for a snug fit
• If needed, warm the gasket slightly to make it more pliable for installation; avoid heat sources that could damage the rubber

Phillips pan head screw for securing panels and components in appliances. Replace missing, stripped, or corroded screws during repairs or maintenance.

Metal sheet-metal screw secures panels, brackets, and internal components. Replace when missing, stripped, or damaged to restore proper fit.

Size: 6-20 x 0.312 inch.

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.