Electrolux Washer Parts

Unscrewed door latch and replaced it with the new door latch (1-2 min). Unscrewed outer plate from door lock assembly. Removed door lock assembly from its outer plate and unplugged wiring. Replaced with new door lock assembly, plugged back in, tightened some screws, double-checked alignment between latch & lock assembly was good and the project was done. Incredibly easy and saved about $150 not having a repair tech come out to fix it. Read more

• Lid or door will not open
• Won't start
• Lid or door won't close

Just removed the old and put on the new,simple.On this Fridgidare washer you should lift the door as you close it which should make the striker last.. Read more

I ran a diagnostics check on the washing machine and came up with the error code E47 -Board thinks the door PTC circuit is open in spin. The washer thought the door was open and would not finish the spin. I was left with a washer full of very wet clothes. This repair was SO extremely easy. I only needed to uses a pair of needle nose pliers and a screw driver. It took less than 10 minutes, start to finish. Now the new door lock assembly registers correctly and my clothes are completely... Read more

Followed youtube instruction video found independently with searching how to fix the problem. Took the top off of the washer. Took off the face of the washer, removed top and bottom exposed balancing weights. Removed old bellow door boot. Did all steps back in reverse. Had a very hard time getting the bellow reattached to the washer as the video was very non-specific of which grove actually attached back onto the water. Read more

• Will not drain
• Noisy

So, Saturday, the washer wouldn't drain, yes, I tried the Drain/Spin cycle. So I took the clothes out, rinsed them out twice in the laundry sink and dried them. After a quick Google search, I came to the conclusion that the pump was bad and ordered a pump, $125. Over the course of the next four days, expecting the new pump on Thursday, I baled out the washer, pulled it out from the wall and propped up the front (it's HEAVY), removed the front access panel, removed the drain inlet and outlet... Read more

• Spins slowly
• Burning smell
• Pumps but will not spin
• Will not agitate

I replaced the spin bearing, tub seal, washer and drive belt since I had it all apart. The video was extremely helpful...I would have tore the whole thing apart trying to figure out how the agitator came off....but it was very simple. Read more

Disassembled dryer. Installed new belt, drum rollers, idler arm and blower. Read more

Replaced it. Read more

• Shakes and moves
• Noisy

I watched the video posted by Jerrod Sessler on yellow van handyman.com. Then I had to unstack the dryer from the washer, remove all covers, disconnect all hose connections, shock mounts and springs and remove the tub assembly. Then I disassembled the tub assembly and remove seal and both bearings from the rear half. At this point I cleaned everything. I installed new bearings and seal, installed the basket and assembled both tub halves using a new gasket and silicone, and reinstalled the... Read more

New water valve. Read more

After tracing the water dripping back up through the inside of the washer I found the water dispenser inlet valve was leaking. I watched several videos to make sure I understood what was involved. I contacted a local parts company to get the part. I also searched online for the part. I found that AppliancePartsPros.com had it cheaper. I ordered late in the afternoon and it arrived the next day. It was fairly easy to installed and saved me a minimum of $99 "diagnostic" fee plus whatever the part... Read more

Replaced pump. All components are accessible from the front of the machine. You have to remove two screws in the back that hold on the top cover, then slide the cover back. This will allow access to the screws that hold on the control panel. Remove the control panel (unplug cable), then remove the spring/wire that holds on the door bellows to the front panel (removing and installing that is the most difficult part of the job) and carefully remove the bellows from the front panel. Then remove... Read more

Had to replace motor and blower, and both were very easy fixes, both pieces fit just right. The do it yourself videos also helped alot too, so props to them...Thanx alot Read more

• No hot or cold water
• Will not stop filling with water

It was really easy to fix. I just took a screw driver and gently pried up on the top of the clothes washer to open up the top. Then the mixing valve was easy to access. I removed the two screws holding and unplugged the the wires. And pulled the old one free. Then reversed the process to install the old one. Less than thirty minutes start to finish. Read more

• Won't start
• Touchpad does not respond

Replaced old knob with new knob Read more

• Will not drain

Replace the drain pump after watching a video demonstrating the process. The washing machine had run properly and emptied, so I was surprised how much water remained in the pipe after disconnecting the old pump. Plan on having 2-3 large towels underneath before removing it. The most difficult part (and most irritating) was replacing the intake and outtake hoses with the existing spring clamps. The drain hose into the pump took almost twenty minutes to attach properly. If the hardware store was... Read more