Columbia Lawn Mower Parts

This damper cylinder is a genuine MTD part, sold individually. This damper cylinder can be used as a replacement part in a lawnmower. The purpose of the damper cylinder in a lawnmower is to facilitate the propelling components of the lawnmower while in operation through the engagement of the pedals.The damper cylinder in a lawnmower might have to be completely replaced within the typical lifespan of the appliance, and this could occur if the damper cylinder is damaged from general wear and tear over long-term usage or as the result of collision with a hard object. If the damper cylinder is damaged, it should be replaced by this genuine OEM replacement part before using the lawnmower again. Remember to always wear gloves when handling, repairing, and operating outdoor equipment. Always unplug the appliance before performing any kind of repair or replacement.Sourced directly from the manufacturer, this component is a genuine replacement part that is sold individually. This damper cylinder is compatible with the following outdoor appliance brands: MTD and Craftsman.

This discharge chute is a genuine MTD part, sold individually. This discharge chute can be used as a replacement part for a snowblower. This discharge chute provides a channel for the passage of snow that has been cleared out of the way by the snowblower so that the snow does not pack up tightly or blow in the face of the operator. The discharge chute of a snowblower might have to be replaced if it is not properly collecting and discharging snow or if the snow is packed too tightly to discharge properly. This could occur if the discharge chute has undergone too much scraping, scratching, or collision with the hard surfaces upon which it might be dragging. If this is the case, the discharge chute should be removed and replaced with this genuine OEM replacement part. Remember to wear work gloves as a safety precaution while repairing or replacing parts within an outdoor appliance. This is an OEM part sourced directly from the manufacturer. It is sold individually. This discharge chute is compatible with the following outdoor appliance brands: MTD and Craftsman.

This part is a replacement sphere bearing assembly. This is a genuine OEM part made by MTD and has been sourced directly from the manufacturer. This part can be used to replace a worn out, damaged, or defective sphere bearing in a variety of outdoor power equipment.Sphere bearings have a variety of uses. They are particularly useful for equipment with a high load capacity that also requires high tolerance and self-aligning ability. They can be found in a wheel assembly, transmissions, or other machinery parts. Sphere bearings are subject to significant wear and tear, requiring replacement. When working on or near to an engine, ensure the equipment is powered off and completely cooled down before starting any repairs. For more accurate information on how and where to install this sphere bearing assembly, the appropriate owner's manual and equipment diagrams should be referenced. As an authentic replacement part, this sphere bearing assembly is suitable for use on several different models of small engine outdoor power equipment manufactured by MTD, Yard Machines, Cub Cadet, Yard Man, Bolens, and Troy-Bilt. This is a genuine part made of high-quality, durable materials and is sold individually.

An oil drain plug keeps the oil where it is supposed to be in the machine. It is designed for use with pieces of outdoor lawn and garden power equipment that have small engines, such as a snow blower, a chipper, a shredder, a lawn mower, and a log splitter. It is compatible with products by brands such as Cub Cadet, Troy-Bilt, and MTD.The oil drain plug part is crucial in preventing oil from leaking when it is not supposed to as well as clearing the path upon removal for any needed oil changes. It is removed when the oil needs to be drained. The replacement or repair process of the oil drain plug should be straightforward, though it may be helpful if the owner or operator uses a socket wrench to aid in the replacement process. The user replacing the part should always be sure to wear gloves during any assembly, replacement, or installation processes. The user should also refer to the owner's manual of their equipment and any guiding diagrams that clarify the placement location.This oil drain plug is made out of threaded metal. This oil drain plug is an original OEM part sourced directly from the manufacturer, MTD. It is sold individually.

This wheel assembly is a durable replacement part created for use with snowblowers, lawnmowers, and other yard equipment. The wheel is the component on the machine that makes it easy for it to be transported and moved around a location. On lawnmowers, it helps with cutting height adjustment to ensure the grass is cut to the right length. It comes with all the components needed to replace the wheel with the exception of required tools.Sometimes wheels can become damaged or will malfunction and require replacement. A visual inspection of each of the wheels will give information about whether a replacement is required. If there is lots of damage or the wheel is broken, it has to be replaced before the lawn tool can be used. The old wheel will need to be removed before the other wheel can be placed. This may require the use of a socket set, wrench set, and screwdriver.This is a genuine OEM replacement part sourced directly from the manufacturer. It's made of durable plastic and is sold individually. The wheel assembly is compatible with lawnmowers, snowblowers, and tillers by MTD, Craftsman, Huskee, Yard-Man, Yard Machines, Bolens, and Troy-Bilt.

The shear pin’s purpose is to stop the engine when it is broken. If the machinery hits something hard, the shear pin will break. This prevents injuries that could be fatal. If something large or small becomes clogged or jammed in the auger, the shear pin is meant to snap in half, rendering the auger useless. This happens once the auger reaches a certain point in pressure load, which also prevents damage to the rest of your equipment. The auger part of your machinery cannot turn without a shear pin. Since the purpose of the shear pin is to break on impact, it's a good idea to have several of these on hand for quick replacements. There’s nothing like having your equipment break down in the middle of a job. Repair is simple. Just remove the broken shear pin, line up the auger’s holes, and insert your new shear pin. Use the cotter pin to secure your shear pin. This genuine OEM auger shear pin works in conjunction with small engine equipment with augers made by Craftsman, Cub Cadet, MTD, Troy-Built, Yard Machines, and Yard-Man. This part is sold individually. Consider also ordering an MTD Pin-Bow Tie Cotter or retaining clip.

The snowblower auger cable initiates operation of the snowblower’s auger similar to the cable on the handle of a push mower. To start the snowblower, the control handle must be squeezed. This engages the snowblower auger cable to allow the auger to begin turning. When the snowblower auger cable is broken, the snowblower cannot work because the auger will not turn. The length of this snowblower auger cable is 47.48 inches. It is made from high-quality rubber insulation of a metal wire. A pair of pliers and a wrench are needed to complete the repair. If the snowblower still does not work after replacing the snowblower auger cable, check the shear pin as these are prone to breaking and will also prevent the auger from turning. This genuine OEM snowblower auger cable is compatible with snowblowers manufactured by Craftsman, Cub Cadet, Husky, MTD, Troy-Bilt, Yard Machines, and Yard-Man. This part is sold individually. You will need to order any hardware, housing, and the trigger separately if these items also need repair or replacement.

The carburetor gasket is installed between the engine and the carburetor body, providing an airtight seal so that all fuel and air going into and out of the carburetor are delivered at optimal pressure for peak engine performance. This gasket can wear down over time and create leaks in the seal, which allows air to escape and can affect the operation of the engine. In the event that the engine won’t stay engaged or isn’t running properly, there may be a problem with the gasket seal. Be sure to let the engine cool completely before working on this part. Drain the gas tank and work in a well-ventilated area. This genuine OEM carburetor gasket replacement will offer an exact fit for compatible lawn and garden equipment engines, including those from MTD, Craftsman, Troy-Bilt, Yard-Man, Husky, and Cub Cadet. This gasket is sold individually as a single part.

In a snowblower, the driveshaft is connected to a part called a worm gear. The worm gear turns the auger blades which eject the snow. The worm gear is connected to the worm shaft, which causes the auger blade to turn rapidly. Eventually, the incredible torque inside the machine, plus the occasional bumps and bruises experienced by the machine in operation and when being stowed, may cause the worm gear to malfunction. When the snowblower is erratic in its operation and fails to remove snow completely, there is a good chance the problem is the worm gear. To replace the worm gear, remove the housing to get to the worm shaft. Remove the entire worm assembly. Next, remove the blower fan and remove the worm gear. Grease the auger assembly before installing the new gear. Reverse the order to reassemble. While the snowblower is disassembled, it's the best time so exam the auger, driveshaft, sheer bolts, and tires for wear. You may find other parts that need to be updated. Make sure to replace the worm bolt and any other necessary parts with a genuine OEM manufactured part such as this one. This gear can be used in a number of snowblowers, including machines made by Yard Machines, Craftsman, Bolens, Yard-Man, Troy-Bilt, Cub Cadet, Ryobi, Montgomery Wards, Huskee, and MTD. Part sold individually.