Parts for Maytag MVWB755DW0: 03 - Console And Dispenser Parts

This control knob attaches to the appliance's control shaft so you can select settings with a solid, positive feel. Replace a cracked, stripped, or missing knob to restore smooth operation and a clean, finished look.

• Attaches to a switch or valve shaft to select temperatures, burner levels, or cycles
• Transfers your hand turn to the control shaft for accurate setting changes
• Common symptoms: cracked hub, spins without engaging, wobbly/loose, falls off, or missing
• Helps maintain a uniform appearance across the control panel

• Disconnect power (and shut off gas, if applicable) before servicing
• Pull the old knob straight off the shaft; avoid prying against the control panel
• Align the insert with the shaft's flats or splines and press straight on until fully seated
• Match position- and finish-specific knobs to the original on models that use different knobs per location

The Wire Harness is an OEM part for Whirlpool washing machines. It comprises a bundle of wires that transmit electrical signals throughout the washer, connecting components like the control panel, motor, pump, and switches. The carefully designed wire routing within the protective sheathing allows all systems to operate in unison. 

Causes of a bad wire harness can be repetitive motion fatigue or damage to the insulation over many machine cycles. Constant vibration may cause wire breaks or shorts within the harness.

Symptoms of a faulty wire harness include: 

• Intermittent or unexpected operation of components  
• Inability to control wash programs or settings
• Error codes or failure detection messages
• Appliance shutting off unexpectedly 

This OEM Whirlpool part is compatible with Maytag, KitchenAid, and some Kenmore models.

The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment. 

Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.

Symptoms of a bad clip include:

• Loose console assembly that is not securely fastened  
• Misaligned or dangling controls that do not sit flush
• Dislodged console at risk of detaching from housing
• Missing clip leaving an open mounting point

This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Rear Panel is an OEM part compatible with Whirlpool washing machines. As the rear housing component, it protects internal mechanisms from debris while providing structure and stability to the cabinet. Its rigid design assists with even weight distribution to minimize vibrations. 

Symptoms of a bad rear panel can include:

• Warping or flexing of the panel material over time
• Cracks developing from pressure changes in the tub area
• Dents compromising the panel's integrity from heavy loads 

Causes of a bad rear panel washer stem from long-term use, with stress and strain accumulating from years of use. Agitator movement and unbalanced loads can warp the panel out of shape.

This OEM Whirlpool replacement rear panel helps restore the washer's protective barrier. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement screw fastens appliance components securely in place. Use it to replace missing, stripped, or corroded hardware so panels, brackets, and covers stay aligned and rattle-free.

• Secures parts such as panels, brackets, covers, or internal assemblies
• Restores alignment and helps eliminate vibration or rattling from loose hardware
• Replaces lost, rusted, or damaged screws during service
• Maintains safe, stable operation by keeping components tight

• Disconnect power before service; if applicable, also shut off water and/or gas
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Use the correct driver bit to prevent stripping the head

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

The Cord-Power is an OEM part for Whirlpool washing machines. It connects the washer to an electrical power source, supplying necessary voltage to operate components including the motor, heater, and control board. The power cord is constructed with durable gauge wire and insulating material to safely handle current flow.  

Causes of a bad power cord can include fraying, cracking or exposed internal wiring from flexing/bending stresses over time, cuts or abrasions that compromise insulation integrity, or failure of the plug/receptacle.

Symptoms of a bad power cord include:

• Intermittent or unreliable power to washer components
• Unexpected shutdowns or rebooting during cycles
• Tripped breakers or blown fuses at the electrical panel
• Tingling, shocks or other safety issues when touching the washer

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Valve is an OEM part for Whirlpool washing machines. This component controls the flow of water into the washing machine during the fill cycle, ensuring that the proper amount of water enters the machine based on the selected settings. The valve is crucial for regulating water levels and maintaining the efficiency and effectiveness of the washing process.

You should replace the valve if it becomes faulty or malfunctions. Causes of a bad valve can include regular wear and tear from frequent use, mineral buildup from hard water, or damage from electrical issues or surges. These problems can lead to the valve not opening or closing properly, which affects the machine's ability to fill with water.

Symptoms of a bad valve include:

• Washing machine not filling with water or filling slowly
• Washer overfilling or water leaking from the machine
• Inconsistent water levels during wash cycles
• Strange noises during the fill cycle

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Wire Harness is an OEM part for Whirlpool washing machines. The wire harness is responsible for transmitting electrical signals that power components and allow them to communicate during each cycle.

Causes of a bad wire harness can be normal wear and tear over time, pinched or cut wires, or wire insulation breakdown due to heat or moisture exposure.

Symptoms of a bad wire harness include:

• Lights or display not working properly
• Washer not starting cycles
• Sensors or switches malfunctioning
• Intermittent operation

This genuine OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Speaker is an OEM component specifically designed for Whirlpool brand washers. It alerts users with chime tones or voice prompts during cycle operation or any error states. Precise acoustic engineering allows for clear audio reception even amid operating vibrations. 

Symptoms of a bad speaker include: 

• No audio tones or voice prompts were heard  
• Muffled, distorted, or unusually loud sounds
• Speaker making rattling or buzzing noises

Causes can be damage from water damage, defects in the audio circuitry, or aging components. 

This speaker ensures optimal user communication. Without it, you cannot verify cycle progress or troubleshoot issues. Its dependable performance maintains the washer's convenience.

This Whirlpool OEM part fits perfectly while extending the equipment's lifespan. It is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

The Bezel is an OEM part compatible with Whirlpool washing machines. This trim piece secures the control console interface within the cabinet opening. Proper mounting provides seamless integration for an aesthetically pleasing appearance.  

Causes of a bad bezel stem from environmental damages over time like cracks or discoloration from cleaning chemicals near the buttons. Repeated impact nicks and dents compromise structural integrity as well.

Symptoms of a bad bezel include:

• Loose hanging appearance no longer firmly fitted  
• Gaps forming entry points for lint and moisture damage
• Detached sections at risk of falling off entirely
• Visual deterioration marring overall style

This Whirlpool replacement bezel restores the finish and protects internal components. It is compatible with brands including Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

This is a replacement screw fastener used to secure appliance components and panels. It restores proper fastening and helps stop loose parts from vibrating or shifting during operation. What it does:

• Secures panels, brackets, or components in place to maintain appliance stability
• Stops rattling, vibration noise, and intermittent contact caused by loose fasteners
• Restores proper alignment where original screws have stripped, corroded, or been lost
• Functions as a direct-fit hardware replacement when the OEM screw is needed

• One replacement screw (quantity: 1)

• Use appropriate driver and moderate torque to avoid stripping threads or damaging parts
• Disconnect power and follow appliance safety procedures before working on the unit
• Repair or replace the mating component as needed

This replacement nut secures appliance parts and hardware to keep assemblies stable and prevent loose connections. It's a simple, direct replacement for worn or missing fastening hardware to restore proper fit and reduce vibration. What it does:

• Fastens mounting studs, brackets or panels to hold components in place
• Restores secure mechanical connections that can loosen over time
• Helps eliminate rattling, vibration and misaligned panels caused by missing or stripped hardware
• Provides a straightforward, durable replacement for corroded or damaged nuts

• Disconnect power to the appliance before beginning any repair
• Use the correct-size wrench or socket; ensure threads engage smoothly before tightening
• Tighten until snug—avoid overtightening that can strip threads or damage components
• Inspect mating threads and replace any damaged studs or hardware for a reliable repair

This is a genuine replacement mounting screw that secures appliance components and panels so parts stay aligned and stable. Installing the correct screw restores proper fit and helps eliminate vibration or loose panels. What it does:

• Fastens panels, brackets, or small components in place
• Replaces missing, stripped, or damaged screws that cause loose parts
• Helps stop rattling, vibration, or misaligned panels
• Restores secure connections after repairs or part replacement

• One mounting screw

• Unplug the appliance or disconnect power before starting work
• Use the correct screwdriver bit to avoid stripping the head
• Tighten until snug; avoid over-tightening which can strip threads or crack plastic
• Keep removed hardware organized so you can reuse existing screws when applicable

The Dispenser Drawer is an OEM replacement part for Whirlpool washing machines. This component holds and dispenses laundry detergent, fabric softener, and bleach into the washer during the appropriate cycle. It ensures accurate distribution of cleaning agents, contributing to effective washing performance.

Symptoms of a bad Dispenser Drawer include:

• Detergent, bleach, or fabric softener not dispensing properly
• Residue buildup in the drawer after the cycle
• The drawer being stuck, difficult to open or close, or visibly damaged

Causes of a failing Dispenser Drawer can include clogs from detergent residue, warping or cracking from long-term use, or mechanical issues with the drawer’s sliding mechanism. Regular cleaning can help prevent issues but eventual wear may require replacement.

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.