Parts for Whirlpool WTW8040DW1: 03 - Console And Dispenser Parts

The Console is an OEM part for Whirlpool front-load washing machines.  Located at the top front of the washer, the console houses all control buttons and a digital display that allows users to set wash cycles and temperature levels. It provides an interface between the user and the inner workings of the washer to start and monitor each cycle.

Causes of a bad console can include damage from liquid leaks or spills, broken or dysfunctional buttons that no longer respond to selections or a faulty digital display. 

Symptoms of a bad console include: 

• Unresponsive or non-functional buttons  
• Inability to select or change wash cycles
• A digital display that does not illuminate or shows error messages
• Damage, cracks, or broken parts

This Whirlpool replacement console is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
 

The Bracket Dryer is an OEM part compatible with Whirlpool dryers. This bracket provides stability and structure by securing the dryer cabinet to the base frame. It is a necessary component that allows for proper mounting and alignment of the dryer. 

Causes of a bad bracket can include cracking, bending, or warping over time and use. Exposure to excessive heat or impact can damage the bracket and compromise its integrity.  

Symptoms of a bad bracket include:

• Vibrating or noisy dryer 
• Loose cabinet that is not firmly mounted
• Difficulty leveling or aligning the dryer
• Stress on other components like doors or panels

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Bracket Dryer is an OEM part compatible with Whirlpool dryers. This bracket provides stability and structure by securing the dryer cabinet to the base frame. It is a necessary component that allows for proper mounting and alignment of the dryer. 

Causes of a bad bracket can include cracking, bending, or warping over time and use. Exposure to excessive heat or impact can damage the bracket and compromise its integrity.  

Symptoms of a bad bracket include:

• Vibrating or noisy dryer 
• Loose cabinet that is not firmly mounted
• Difficulty leveling or aligning the dryer
• Stress on other components like doors or panels

This OEM Whirlpool replacement part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The wire harness is an OEM part for Whirlpool washing machines. This harness is a network of color-coded wires that connect the machine's electrical control module to other components. It allows for the transmission of power and data necessary for operating wash cycle functions.

Causes stem from normal wear over time as wires endure constant motion during every cycle. Accidental cuts or exposed wires from damage can also cause failures.

Symptoms of a bad wire harness include:

• The washer not starting or only partially functioning
• Error codes displaying or cycles not completing properly
• Corrosion or physical damage seen on wire connectors

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.

The Console Clip is an OEM part compatible with Whirlpool dryers. This clip secures the control console assembly to the top panel, ensuring it is firmly mounted during operation. Properly functioning clips are necessary to maintain the correct alignment of controls and prevent detachment. 

Causes of a bad clip can include wear and fatigue from repeated opening and closing of the dryer door. Excessive force or impact could also bend or break the clip over time.

Symptoms of a bad clip include:

• Loose console assembly that is not securely fastened  
• Misaligned or dangling controls that do not sit flush
• Dislodged console at risk of detaching from housing
• Missing clip leaving an open mounting point

This OEM Whirlpool replacement clip is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Rear Panel is an OEM part compatible with Whirlpool washing machines. As the rear housing component, it protects internal mechanisms from debris while providing structure and stability to the cabinet. Its rigid design assists with even weight distribution to minimize vibrations. 

Symptoms of a bad rear panel can include:

• Warping or flexing of the panel material over time
• Cracks developing from pressure changes in the tub area
• Dents compromising the panel's integrity from heavy loads 

Causes of a bad rear panel washer stem from long-term use, with stress and strain accumulating from years of use. Agitator movement and unbalanced loads can warp the panel out of shape.

This OEM Whirlpool replacement rear panel helps restore the washer's protective barrier. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear panel onto the cabinet frame, ensuring a sturdy connection between housing components.  Proper installation is critical for the washer's structural integrity.

Causes of a bad screw include corrosion from repeated water exposure or stresses from years of use. Loosening can occur from vibrations weakening the threads over time. 

Symptoms of a bad screw include:

• Rear panel detaching from frame opening gaps
• Increased noise and vibrations from a compromised seal  
• Stress on other connections from improper mounting points
• Potential leak paths from openings near hoses or tub areas

This OEM Whirlpool replacement screw helps maintain a tight panel closure. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

This replacement seal is the rubber gasket that helps form a watertight barrier between the washer tub and front opening, reducing leaks and keeping laundry contained during cycles. It restores a snug, reliable seal when the original is worn or damaged. What it does:

• Creates a waterproof barrier to prevent water from escaping the tub during wash and rinse cycles
• Helps keep clothes and suds inside the drum for proper operation
• Reduces trapped moisture that can lead to mildew and odors
• Symptoms: visible tears, cracks, flattened or deformed rubber, water pooling on the floor near the door

• Disconnect power and turn off the water supply before starting any repairs
• Inspect the door opening and tub lip; clean surfaces to ensure a proper fit
• Stretch and seat the seal evenly around the tub opening; ensure any retaining bands or clamps are properly positioned

The Power Cord is an OEM component compatible with Whirlpool washing machines. This power cord safely transmits electricity from the wall outlet to internal control boards and heating elements. Maintaining its integrity is vital for safe operation. 

Causes of bad power cord include cracked or worn insulation exposing live wires over multiple years of use. Repeated bending during installation can cause breaks in the internal copper strands.

Symptoms of a bad power cord include: 

• Intermittent power or failure to turn on fully  
• Tripped circuit breakers during heavy usage cycles
• Frayed or cracked areas increase shock/fire hazard
• Discoloration or brittleness indicating advanced breakdown

This Whirlpool replacement cord restores reliable power delivery. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Screw is an OEM component compatible with Whirlpool washing machines. This screw secures the rear bulkhead to the tub, ensuring vibrations are reduced through solid mounting points. Properly installed screws dampen oscillating movement.

Causes of a bad screw include damage from water exposure like corrosion or breakage from stress concentrations if the tub bangs around during imbalanced loads. 

Symptoms of a bad screw include:

• Loose or detached rear bulkhead allowing side-to-side play
• Excessive noise and shaking felt through the surrounding walls   
• Development of micro-cracks around screw holes over time
• Potential leak paths if holes are no longer sealed 

This Whirlpool replacement screw restores a stable suspension system. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Water Inlet Valve is an OEM component compatible with Whirlpool washing machines. This valve controls water flow into the tub by opening at predetermined points in the cycle. Proper water regulation is necessary for optimum cleaning performance.

Symptoms of a bad water inlet valve include:

• Slow or inconsistent filling during initial cycle phases   
• Premature displays of out-of-balance errors due to low water levels
• Inoperable cycles missing crucial wash or rinse stages 

Causes stem from mineral buildup obstructing valve ports over time. Mechanical failure could also prevent actuation from electrical commands sent by the control board.

This Whirlpool replacement valve restores accurate flow control. It is compatible with additional brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Wire Harness is an OEM part for Whirlpool washers. Found running throughout the washer cabinet, this bundle of electrical wires safely routes power between key mechanisms. 

Symptoms of a bad wire harness include:

• Buttons/controls failing to function properly  
• Cycle programs or options not responding
• Compressor or motor randomly cutting off
• Circuit board issues due to loose connections

Causes can be wear over time from vibration in the washer leading to insulation cracks, wire breaks or loose connections that disrupt current flow. Accidental splices during repairs are also possible.

This OEM replacement harness is compatible with Maytag, KitchenAid, and more appliance brands.

The Speaker is an OEM component specifically designed for Whirlpool brand washers. It alerts users with chime tones or voice prompts during cycle operation or any error states. Precise acoustic engineering allows for clear audio reception even amid operating vibrations. 

Symptoms of a bad speaker include: 

• No audio tones or voice prompts were heard  
• Muffled, distorted, or unusually loud sounds
• Speaker making rattling or buzzing noises

Causes can be damage from water damage, defects in the audio circuitry, or aging components. 

This speaker ensures optimal user communication. Without it, you cannot verify cycle progress or troubleshoot issues. Its dependable performance maintains the washer's convenience.

This Whirlpool OEM part fits perfectly while extending the equipment's lifespan. It is compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and select Kenmore washers.

This replacement screw secures panels, brackets, and other components in your appliance to keep them aligned and rattle-free. Replacing worn, stripped, or missing hardware restores a tight fit and helps maintain safe, quiet operation.

• Fastens panels, brackets, or internal parts to the cabinet/frame
• Helps maintain alignment to reduce vibration and rattling
• Replaces lost, stripped, or corroded screws
• Common symptoms: loose panels/trim, rattles, or a screw that won't tighten

• Disconnect power; shut off water or gas if applicable
• Match thread and length to the original; replace one at a time to keep alignment
• Start threads by hand to avoid cross-threading; use the correct driver
• Tighten snugly—do not overtighten, especially into plastic or thin sheet metal

The Bezel is an OEM part compatible with Whirlpool washing machines. This trim piece secures the control console interface within the cabinet opening. Proper mounting provides seamless integration for an aesthetically pleasing appearance.  

Causes of a bad bezel stem from environmental damages over time like cracks or discoloration from cleaning chemicals near the buttons. Repeated impact nicks and dents compromise structural integrity as well.

Symptoms of a bad bezel include:

• Loose hanging appearance no longer firmly fitted  
• Gaps forming entry points for lint and moisture damage
• Detached sections at risk of falling off entirely
• Visual deterioration marring overall style

This Whirlpool replacement bezel restores the finish and protects internal components. It is compatible with brands including Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

The Detergent Dispenser Drawer is an OEM part for Whirlpool washing machines. It is responsible for holding and dispensing detergent and other laundry additives during the wash cycle. The dispenser drawer ensures that these cleaning agents are released at the appropriate times for optimal washing performance.

Over time, the detergent dispenser drawer can become clogged or damaged due to residue buildup, improper use, or general wear and tear. Such issues can hinder the proper dispensing of detergent, affecting the cleanliness of your laundry.

Symptoms of a bad detergent dispenser drawer include:

• Detergent not dispensing properly
• Water not flowing into the drawer
• Leaks from the dispenser area
• Stuck or difficult-to-open drawer

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This replacement screw fastens appliance components securely in place. Use it to replace missing, stripped, or corroded hardware so panels, brackets, and covers stay aligned and rattle-free.

• Secures parts such as panels, brackets, covers, or internal assemblies
• Restores alignment and helps eliminate vibration or rattling from loose hardware
• Replaces lost, rusted, or damaged screws during service
• Maintains safe, stable operation by keeping components tight

• Disconnect power before service; if applicable, also shut off water and/or gas
• Start threads by hand to avoid cross-threading; tighten snugly without over-torquing
• Use the correct driver bit to prevent stripping the head

This Control Panel is an OEM part for Whirlpool Washers. It houses the buttons and controls for operating the washing machine. Continuous use or water exposure can cause issues with this part.

What Causes a Bad Control Panel:
Continuous use, water exposure, or electrical faults can cause malfunctioning buttons, display errors, or control issues.

Symptoms of a Bad Control Panel:

• Non-responsive buttons or control panel
• Display errors or flickering
• Water leaks from the control panel area

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.