Parts for Frigidaire GL27M6WXFA: 04 - Console And Control Parts

Color: white. Measures about 1-1/2 inches in diameter.

This mechanical temperature control thermostat regulates refrigerator temperature to keep food cold and cycling the compressor as needed. Replaces a faulty control to restore proper cooling performance and temperature stability. What it does:

• Senses cabinet temperature and opens/closes the compressor circuit to maintain set temperature.
• Stops the compressor when the refrigerator reaches the selected temperature and restarts it as needed.
• Commonly replaced when the fridge runs continuously, won't reach set temperature, or has erratic cooling cycles.
• May produce a clicking sound when switching or fail to make electrical contact, causing cooling loss.

• Disconnect power to the appliance before starting any repair.
• Access may require removing interior panels or control housing; keep track of fasteners and wire locations.
• Verify wiring and operation with a multimeter; replace only with the correct OEM part.

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This vane screw secures the internal drum baffle (vane) to the drum, keeping loads turning properly and preventing rattles or snags. Replace a missing or stripped screw to restore a tight, stable baffle during cycles.

• Fastens the drum baffle/lifter (vane) to the rotating drum
• Helps maintain proper tumble and load turnover
• Common symptoms: loose or wobbly baffle, rattling or clunking noises, items catching on a raised baffle edge, or a baffle that detaches
• Visual cues: missing screw or stripped/damaged threads at the baffle mounting holes

• Disconnect power before servicing; shut off gas
• Access the baffle from inside the drum; align holes and start the screw by hand to avoid cross-threading
• Tighten firmly but do not overtighten to prevent stripping the drum or cracking the baffle
• Start all screws before final tightening to seat the baffle evenly

This factory 8-18 screw secures appliance panels, brackets, and components. Replace missing or stripped hardware to restore a tight, rattle-free assembly and dependable operation.

• Fastens components to frames, brackets, and covers
• Replaces missing, damaged, or rusted screws
• Helps reduce looseness, vibration, and rattling noises
• Restores proper alignment of panels and assemblies

• Disconnect power before servicing; shut off gas/water if applicable
• Start the screw by hand to avoid cross-threading; use the proper driver
• Tighten snugly—do not overtighten to prevent stripping metal or plastic

This replacement timer knob mounts to the control timer shaft, allowing you to select cycles and settings with a positive, secure feel. Replacing a cracked or stripped knob restores smooth, accurate control of the timer.

• Attaches to the timer shaft so you can rotate and set the desired cycle
• Restores function when the original knob is cracked, loose, or stripped
• Helps resolve issues like the knob spinning freely, wobbling, or falling off
• Provides firm, reliable engagement for precise timer adjustments

• Disconnect power to the appliance before servicing
• Pull the old knob straight off the timer shaft; retain and transfer any inner spring clip if present
• Align the new knob with the flat side or splines of the shaft and press on until fully seated
• Support the control panel during removal/installation and avoid excessive force

PPH ab st/z/ch `6 - 18x.60

A replacement mounting screw used to secure components on compatible Frigidaire appliances. This genuine-style fastener restores proper fit where the original screw is missing, stripped, or damaged for safe operation. What it does:

• Secures trim, panels, brackets, or components to prevent rattling and misalignment
• Restores a proper mechanical connection when the original screw is lost or worn
• Helps eliminate vibration noise caused by loose fasteners
• Compatible with specific Frigidaire assemblies that use this style of screw

• Screw only

• Use the correct screw location and size—do not force or overtighten to avoid stripping threads or cracking plastic parts
• Turn off power or disconnect appliance from power source before accessing internal components
• Wear safety glasses and handle small parts carefully to avoid injury or loss

This wiring clip secures a refrigerator's wire harness to the cabinet or components to prevent chafing and keep wires organized. It helps maintain safe routing and reduces strain on electrical connections. What it does

• Holds wiring harness in place to prevent rubbing against sharp edges or moving parts
• Keeps wires organized to reduce the risk of pinching or accidental disconnection
• Helps prevent intermittent electrical faults caused by loose or strained wiring
• Commonly used near compressor, fan, control box, or rear cabinet areas

• Install by snapping the clip onto the cabinet flange or component and routing the harness through the retainer
• Disconnect power before accessing electrical components or wiring
• Inspect surrounding wiring and insulation; replace any damaged wire or harness tape before reinstalling the clip