Parts for Frigidaire DG250EXF1: 03 - Console, Controls, Top Panel, Misce Parts

This part has been discontinued by the manufacturer and is no longer available.

Replace your dryer's timer dial if it's cracked, broken, or won't turn properly. This control dial mounts on the timer shaft to set drying cycles.

This is a replacement mounting screw used to secure a solenoid valve or solenoid assembly in appliances. It provides a durable fastening point so the solenoid stays properly positioned and functions reliably. What it does:

• Secures solenoid valves or solenoid assemblies to the appliance frame or bracket
• Helps maintain correct alignment for valve operation and connections
• Prevents loosening from vibration or normal use
• Suitable where the OEM fastener is required for a proper fit

• Use the matching screw size and thread pattern listed in the appliance parts diagram
• Tighten to snug only; overtightening can strip threads or damage the solenoid housing
• Disconnect power and shut off water before servicing the appliance
• If other fasteners or damaged components are present, inspect and replace as needed

This small clip secures the wire harness inside the dryer, keeping it routed properly and preventing it from contacting moving parts or heat sources. It snaps onto the frame or panel to hold wiring bundles in place. Replace this clip if it has broken or gone missing during a previous repair, leaving wiring loose or unsecured.

This part has been discontinued by the manufacturer and is no longer available.

Hex washer head ,10-32 x 0.375. Ground

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This is a flexible, putty-like sealing compound strip used to create airtight and watertight seals on refrigerators and ice machines. It is typically applied around joints, tubing connections, or panel seams to prevent air and moisture leaks. Replace this sealing strip if you notice frost buildup, condensation, or temperature fluctuations caused by a deteriorated or missing seal.

This part has been discontinued by the manufacturer and is no longer available.

This part has been discontinued by the manufacturer and is no longer available.

This is a flexible, putty-like sealing compound strip used to create airtight and watertight seals on refrigerators and ice machines. It is typically applied around joints, tubing connections, or panel seams to prevent air and moisture leaks. Replace this sealing strip if you notice frost buildup, condensation, or temperature fluctuations caused by a deteriorated or missing seal.

The High Temp Lubricant Tube is an OEM part for Frigidaire appliances, specifically designed to withstand and operate under high temperature conditions. This lubricant is essential for the proper maintenance and functionality of various Frigidaire appliances, offering protection against heat and friction. 

Over time, the lubricant can degrade or become contaminated, which can compromise its effectiveness. Causes of a bad high temp lubricant include exposure to extreme temperatures, accumulation of dirt and debris, or simply the natural breakdown of the lubricant over prolonged use.

Symptoms of needing a new High Temp Lubricant Tube include:

• Increased noise during appliance operation
• Reduced efficiency or performance of the appliance
• Harder movement of parts that should glide smoothly

This OEM Frigidaire part is also compatible with Electrolux, Gibson, Kelvinator and some Kenmore models.

The High Temperature Adhesive is an OEM part for Frigidaire appliances. This adhesive is specifically formulated to withstand high temperatures and is used in various repair applications within appliances such as ovens, ranges, and dryers.The 1-ounce tube contains adhesive formulated to withstand the extreme heat inside dryer drums and cabinets

Causes of a bad adhesive can include exposure to extremely high temperatures over extended periods, contamination by dirt or grease, or the natural aging and drying out of the adhesive.

Symptoms of a bad high temperature adhesive include:

• Components or parts becoming loose or detached
• The adhesive becoming brittle or cracked
• Inability to properly bond surfaces exposed to high heat
• Visible deterioration or peeling of the adhesive

This OEM replacement is also compatible with Electrolux, Gibson, Kelvinator, and Kenmore models.

Supports and allows smooth drum rotation in your dryer. Replace if you hear squealing, grinding, or rattling noises during operation. Verify fit with your model.