Parts for Kitchenaid KUCV151MMT1: 04 - Container Parts

This stainless container panel replaces a damaged or worn front for the refrigerator's storage container, restoring the compartment's appearance and helping the drawer close cleanly. It matches OEM fit and finish for a factory look. What it does:

• Replaces a scratched, dented, or corroded container/front panel
• Restores the drawer/container appearance and front edge alignment
• Helps the drawer seal and slide as intended when the front is intact
• Fits into the existing container assembly and uses factory mounting points

• One stainless container panel

• Requires basic disassembly of the container/drawer; keep fasteners and clips organized
• Inspect mating edges and clips for damage; replace any broken hardware separately
• Disconnect power only if working near electrical components; follow appliance-specific service manual

This replacement container restores a secure, factory-fit compartment in your appliance. Install a new container when the original is cracked or broken to keep contents properly held and nearby parts aligned as designed.

• Provides the designated compartment to hold contents securely
• Interfaces correctly with its mounting points, guides, or adjoining parts
• Replaces cracked, warped, or broken containers that won't stay seated
• Helps prevent spills, jams, or interference with nearby components

• Disconnect power to the appliance; shut off water supply if applicable
• Wear cut-resistant gloves—damaged plastic edges can be sharp
• Move any screws, covers, or inserts from the old part to the new one
• Align tabs, tracks, or snaps and press into place without forcing

This is a replacement machine screw sized 8-18 x 3/8 that secures panels and components on compatible appliances. It restores proper fastening where a worn, stripped, or missing screw causes loose parts or rattling. What it does

• Fastens control panels, trim pieces, or brackets to the appliance chassis
• Replaces stripped, corroded, or missing screws that cause loose panels or vibrating noise
• Provides correct thread engagement for a secure hold in tapped holes
• Small hardware solution often used during door, console, or interior repairs

• One 8-18 x 3/8 machine screw (quantity: 1)

• Use the correct screw size and thread; do not force a different-size fastener into tapped holes
• Hand-start the screw to avoid cross-threading, then tighten with the appropriate screwdriver
• Disconnect power before accessing internal components or panels on electrical appliances
• If metal threads are damaged, repair with a helicoil or replace the damaged component rather than over-torquing

This replacement foot pedal mounts at the base of the trash compactor to provide hands-free drawer release. Replace a worn, cracked, or missing pedal to restore easy opening, proper latch engagement, and smooth operation. What it does:

• Engages the drawer release mechanism when stepped on
• Enables hands-free access when your hands are full
• Helps ensure the drawer opens and latches correctly
• Helps with symptoms such as a broken/missing pedal, difficulty opening the drawer, or a pedal that feels loose or does not return

• One foot pedal

• Disconnect power to the compactor and empty the drawer before servicing
• Remove the toe panel or mounting screws to access the pedal attachment points
• Reuse existing mounting hardware from the original pedal, aligning the new pedal correctly
• Verify smooth pedal action and proper drawer release before restoring power

Size: 8-32 x 3/8 inch.

This door lock latch assembly secures the washer door during operation so cycles can run safely and water stays contained. It replaces a worn or damaged latch to restore proper door locking and cycle start. What it does

• Secures and locks the washer door during wash and spin cycles so the appliance can operate normally.
• Triggers the door-closed sensor/switch that allows the washer to start and continue a cycle.
• Helps prevent accidental door opening and reduces the risk of leaks during operation.
• Common symptoms indicating this part may be needed: washer won't start, door won't latch or lock, or the latch feels loose or broken.

• Always disconnect power to the appliance before inspecting or replacing the door lock latch.
• Handle the door and glass carefully to avoid damage; align the latch with the strike before tightening fasteners.
• After installation, test a short cycle (no clothes) to ensure the door locks and the washer starts properly.

This safety switch actuator engages the door/interlock switch so the appliance senses a closed, secure door and will run as intended. Replacing a worn actuator restores reliable door engagement and control-system signaling. What it does:

• Moves the door latch into position to trip the appliance's safety/interlock switch
• Ensures the control board senses a closed door so cycles can start or continue
• Common symptom: appliance won't start or stops when the door is shut or nudged
• Common symptom: door won't fully latch or feels loose when closing

• One safety switch actuator

• Disconnect power (and water if applicable) before starting any repair
• Remove exterior panels or door assembly as needed to access the actuator; keep fasteners organized
• Verify switch alignment with the actuator and test operation before reassembly
• Wear gloves and eye protection

Size: 8-18 x 1/2 inch.

Size: 8 x 1/2 ab.

This container roller bearing supports the trash compactor drawer as it slides on its tracks. Replacing a worn bearing restores smooth, quiet movement and helps keep the container aligned for easy opening and closing.

• Provides low-friction support so the drawer glides smoothly on the tracks
• Helps maintain proper container alignment and stability
• Reduces squeaks, grinding, and sticking during operation
• Common symptoms: drawer hard to open/close, scraping noises, binding or uneven movement, visible wear/flat spots on the bearing

• Disconnect power to the compactor before servicing
• Remove and empty the drawer to access the bearing location
• Install the new bearing in the same orientation; transfer any hardware as needed
• Inspect rollers, axles, and tracks; replace any additional worn parts for best results

Size: 3\8-24 inch.

This E-ring retaining clip secures latch components by locking onto a shaft or pin so the latch assembly stays in place. It's a small but essential metal clip that prevents latch parts from slipping off and causing door or panel issues. What it does:

• Locks onto latch shafts or pins to hold the latch assembly together
• Prevents the latch or related parts from sliding off during operation
• Common symptoms: door or panel won't stay closed, rattling or loose parts near the latch, visible clip missing or deformed
• Helps restore secure engagement of the latch when the clip is intact and correctly positioned

• One E-ring retaining clip

• Disconnect power or unplug the appliance before beginning any repair
• Use pliers or snap-ring tools to remove/install the clip; avoid excessive force that could deform it
• Replace the clip if it is bent, cracked, or worn — do not reuse a damaged clip

This latch plate secures the appliance door to the cabinet, providing the positive engagement needed for proper door closure and operation. It helps restore a door that won't stay closed or won't trigger door switches. What it does:

• Acts as the door strike that the latch engages to hold the door shut
• Ensures the door closes firmly so door switches can register a closed state
• Can stop issues like a loose or misaligned door, or a door that won't remain closed
• Restores proper alignment and engagement without replacing the full latch assembly

• Disconnect power (and gas if applicable) before servicing
• Remove the door or access panel to reach the latch area
• Inspect related latch components and alignment; replace only the damaged part
• Use basic hand tools; tighten fasteners securely but avoid overtightening

This sheet-metal pan-head screw secures appliance panels, brackets, and components to the cabinet or frame. Replacing a missing or damaged screw restores a tight fit and helps stop rattles, misalignment, and loosening.

• Fastens sheet-metal panels, covers, ducts, and brackets to the appliance chassis
• Helps keep components aligned and secure during operation
• Replace if the original is missing, rusted, stripped, or damaged
• Common symptoms: loose or vibrating panels, gaps or misaligned parts, hardware that won't tighten

• Disconnect power; shut off gas or water supply before servicing
• Support the panel or part being attached; hand-start threads to avoid cross-threading
• Use the correct driver bit; tighten snugly but do not overtighten into sheet metal
• If multiple matching screws secure a part, consider replacing them as a set for consistent hold

Fits 15 and 18 inch compactors. This kit is for securing the compactor bags. Kit contains a set of 4 buttons and screws.

The Actuator Switch Kit is an OEM part for Whirlpool trash compactors. This part activates the compaction cycle when the trash compactor's door is shut and locked, ensuring the unit operates safely and effectively. The actuator switch signals the control system to start the compaction process, an essential step in reducing the volume of waste.

Causes of a malfunctioning actuator switch can include prolonged use leading to mechanical wear, electrical failures within the switch itself, or misalignment issues with the compactor's door. 

Symptoms of a bad Actuator Switch Kit include:

• The compactor fails to start the compaction cycle
• The system starts only intermittently or not at all
• Unexpected halting of the compaction process
• The need to manually engage or adjust the switch to start the cycle

This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.