Parts for Whirlpool GC900QPPB7: Container Parts

Replacement refrigerator door handle that restores a secure grip and proper door operation. Installs in place of a broken, cracked or loose handle to make opening and closing the fridge easier and safer. What it does:

• Replaces a damaged or cracked refrigerator door handle so the door can be opened and closed normally.
• Provides a secure gripping surface to reduce slipping and improve user control.
• Stops further damage to the door trim or mounting points caused by a worn, loose, or broken handle.
• Matches original mounting points on compatible appliances for a straightforward replacement.

• Read the appliance manufacturer's instructions before starting; keep original fasteners unless replacements are provided.
• Use basic hand tools; avoid forcing parts—inspecting mounting tabs can prevent additional damage.
• Disconnect power to the appliance before working near electrical components; if the door has integrated wiring (e.g., lights or dispensers), follow manufacturer safety guidance.

This replacement handle restores a secure, comfortable grip on your appliance's front panel, helping you open and close the door or drawer with confidence. It renews both function and appearance when the original handle is cracked or loose.

• Provides the leverage needed to open and close the door/drawer
• Direct replacement for a broken, cracked, worn, or wobbly handle
• Can help resolve difficulty pulling the panel open due to a loose handle
• Refreshes the appliance's exterior appearance

• Disconnect power before servicing
• Support the panel while removing the old handle to avoid stressing hinges
• Align the new handle and reuse the original mounting hardware/end caps as applicable; tighten evenly without overtightening
• Test for a secure fit and smooth operation

This replacement container restores a secure, factory-fit compartment in your appliance. Install a new container when the original is cracked or broken to keep contents properly held and nearby parts aligned as designed.

• Provides the designated compartment to hold contents securely
• Interfaces correctly with its mounting points, guides, or adjoining parts
• Replaces cracked, warped, or broken containers that won't stay seated
• Helps prevent spills, jams, or interference with nearby components

• Disconnect power to the appliance; shut off water supply if applicable
• Wear cut-resistant gloves—damaged plastic edges can be sharp
• Move any screws, covers, or inserts from the old part to the new one
• Align tabs, tracks, or snaps and press into place without forcing

Size: 8-18 x 1/2 inch.

This is a replacement machine screw sized 8-18 x 3/8 that secures panels and components on compatible appliances. It restores proper fastening where a worn, stripped, or missing screw causes loose parts or rattling. What it does

• Fastens control panels, trim pieces, or brackets to the appliance chassis
• Replaces stripped, corroded, or missing screws that cause loose panels or vibrating noise
• Provides correct thread engagement for a secure hold in tapped holes
• Small hardware solution often used during door, console, or interior repairs

• One 8-18 x 3/8 machine screw (quantity: 1)

• Use the correct screw size and thread; do not force a different-size fastener into tapped holes
• Hand-start the screw to avoid cross-threading, then tighten with the appropriate screwdriver
• Disconnect power before accessing internal components or panels on electrical appliances
• If metal threads are damaged, repair with a helicoil or replace the damaged component rather than over-torquing

This door lock latch assembly secures the washer door during operation so cycles can run safely and water stays contained. It replaces a worn or damaged latch to restore proper door locking and cycle start. What it does

• Secures and locks the washer door during wash and spin cycles so the appliance can operate normally.
• Triggers the door-closed sensor/switch that allows the washer to start and continue a cycle.
• Helps prevent accidental door opening and reduces the risk of leaks during operation.
• Common symptoms indicating this part may be needed: washer won't start, door won't latch or lock, or the latch feels loose or broken.

• Always disconnect power to the appliance before inspecting or replacing the door lock latch.
• Handle the door and glass carefully to avoid damage; align the latch with the strike before tightening fasteners.
• After installation, test a short cycle (no clothes) to ensure the door locks and the washer starts properly.

Size: 8 x 1/2 ab.

Color: White

This safety switch actuator engages the door/interlock switch so the appliance senses a closed, secure door and will run as intended. Replacing a worn actuator restores reliable door engagement and control-system signaling. What it does:

• Moves the door latch into position to trip the appliance's safety/interlock switch
• Ensures the control board senses a closed door so cycles can start or continue
• Common symptom: appliance won't start or stops when the door is shut or nudged
• Common symptom: door won't fully latch or feels loose when closing

• One safety switch actuator

• Disconnect power (and water if applicable) before starting any repair
• Remove exterior panels or door assembly as needed to access the actuator; keep fasteners organized
• Verify switch alignment with the actuator and test operation before reassembly
• Wear gloves and eye protection

This container roller bearing supports the trash compactor drawer as it slides on its tracks. Replacing a worn bearing restores smooth, quiet movement and helps keep the container aligned for easy opening and closing.

• Provides low-friction support so the drawer glides smoothly on the tracks
• Helps maintain proper container alignment and stability
• Reduces squeaks, grinding, and sticking during operation
• Common symptoms: drawer hard to open/close, scraping noises, binding or uneven movement, visible wear/flat spots on the bearing

• Disconnect power to the compactor before servicing
• Remove and empty the drawer to access the bearing location
• Install the new bearing in the same orientation; transfer any hardware as needed
• Inspect rollers, axles, and tracks; replace any additional worn parts for best results

Fits 15 and 18 inch compactors. This kit is for securing the compactor bags. Kit contains a set of 4 buttons and screws.