Parts for Lg WT4870CW: Control Panel Assembly Parats Parts

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

This rear cabinet panel replaces the damaged or worn outer back cover on your appliance, restoring structural protection and keeping internal components shielded from dust and debris. It helps maintain safe operation and appliance appearance. What it does:

• Covers and protects internal components at the back of the appliance
• Prevents dust, dirt, and small objects from entering service areas
• Restores proper airflow paths and enclosure integrity when the original panel is dented or missing
• Reduces vibration noise caused by loose or damaged rear panels

• Disconnect power (and water supply if applicable) before beginning any repair
• Use appropriate fasteners and torque to secure the panel; do not overtighten to avoid cracking
• If sharp edges are present, wear gloves and eye protection during installation

Replace your washer's front panel assembly if the exterior panel is cracked, dented, or damaged. This cosmetic component covers the front of the unit.

This knob assembly replaces a worn or broken control knob so you can reliably set and adjust appliance settings. It restores a secure, easy-to-turn interface for the appliance's control shaft. What it does:

• Fits onto the control shaft to allow manual selection of settings and temperatures.
• Replaces cracked, stripped, or loose knobs that no longer grip the control shaft.
• Helps resolve issues where the control won't turn smoothly or slips while changing settings.
• Restores tactile feedback for accurate user control.

• Disconnect power to the appliance before removing or installing the knob.
• Pull the old knob straight off the control shaft.
• Align the knob's internal splines with the control shaft and push until fully seated.
• If knob does not seat or control still slips, inspect shaft splines and replace damaged components as needed.

Designed for use on a washing machine unit, this is a control board. This part manages the washing machine's functions, including filling with water, the wash cycle, draining the tub, and the spinning cycle. This is an essential component for the washing machine and if it is not working properly, nothing will work on the unit.The washing machine may not fill the tub with water or advance through any of the cycles if this part has gone bad. These cycles include washing, draining, and spinning. Unplug the washing machine before performing care or maintenance on the unit. Wearing work gloves is recommended for safety to ensure that the hands are not injured during this process. The control board is sold individually. It comes directly from the manufacturer and is a genuine and durable replacement part. This particular part is compatible with washing machine units that are manufactured by the LG brand.

Protective cover for washer control panel or component housing. Replaces cracked, broken, or missing covers. Shields internal parts from damage.

Molded trim piece that shields and supports the washer guide track assembly. Replace if cracked, broken, or missing to maintain smooth alignment.

Fix DL error code or washer that won't start with this lid switch and lock assembly. DIY repair in about 20 minutes with basic tools and video guide.

Secures internal washer components in proper alignment. Replace this mounting bracket if cracked, rusted, broken, or missing to restore stability.

Dispenses detergent, softener, and bleach during wash cycles. Replace if cracked, clogged, or disintegrated. Confirm fit with your model number.

Replace a cracked or clogged washer nozzle assembly to restore proper water flow and prevent poor cleaning performance. Moderate DIY repair.

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.

Washer won't fill or won't stop filling? This water inlet valve controls water flow into the tub. DIY-friendly repair, typically takes 10-15 minutes.

This inlet hose routes incoming water from the washer's fill valve into the machine to support proper filling. Replace a cracked or leaking hose to stop drips, prevent water damage, and restore reliable fill performance.

• Directs incoming water from the fill valve to the dispenser/tub during wash cycles
• Maintains a sealed path to prevent internal or external leaks
• Helps the washer reach proper fill levels and timing
• Common symptoms of failure: water on the floor, leaks during fill, visible cracks or bulges, long/no fill or IE error

• Unplug the washer and turn off both hot and cold water supplies
• Keep towels or a pan handy; relieve residual water pressure before disconnecting
• Note the original routing; fully seat the hose on fittings and secure with existing clamps
• Restore water and power, then run a quick fill to check for leaks

Fix detergent leaks or dispenser jams with this washer detergent housing assembly. Routes detergent properly and replaces cracked or warped housings.

Fix washer overfilling or not filling issues with a water level pressure switch replacement. Common repair for PE error codes. Takes 10-20 minutes to install.

This snap ring is a small retaining clip that secures shafts, bearings, or other rotating parts in place to prevent lateral movement and maintain correct alignment. It helps keep assemblies stable during normal appliance operation. What it does:

• Holds components on a shaft or in a housing to prevent shifting or coming loose
• Maintains alignment of rotating parts to reduce wear and vibration
• A missing or damaged snap ring can allow parts to move, causing noise, binding, or component failure
• Works as a low-profile, durable mechanical fastener for confined spaces

• Disconnect power before starting any repair and follow appliance-specific safety guidance
• Use proper snap-ring (circlip) pliers to remove and install to avoid deformation or injury
• Inspect the groove and mating parts for wear or damage before installing the new ring

Suppresses electrical interference on your washer's AC power line to protect control boards. Replace if washer won't power on, stops mid-cycle, or controls malfunction. Verify fit by model number.

Fix leaks or poor water flow with a new washer inlet hose. This part channels household water supply into your machine for proper filling and operation.

Fix dispenser overflow or leaking issues with this washer detergent drawer assembly. Channels water through detergent and softener compartments. DIY repair.

Secures hose connections to maintain watertight seals in your washer. Replace if you notice leaks or loose hoses during operation. Verify fit with model number.

This small cover cap conceals an exposed fastener or opening on your appliance, restoring a clean, finished look. It also helps protect the area from dust and splashes for a tidy, long-lasting installation.

• Covers and protects an open screw hole or attachment point on a panel or door
• Restores a clean, factory appearance
• Helps keep dust and moisture out of the opening
• Common signs it's needed: missing cap, cracked/broken cap, loose cap, won't stay clipped

• Disconnect power (and water, if applicable) before servicing exterior panels or doors
• Note the cap's orientation and any retaining tabs before removal
• Use a plastic pry tool to gently release the old cap; press the new cap until fully seated
• Avoid forcing the cap or overtightening any underlying fastener to prevent damage

Dissolves odor-causing residue and mildew buildup in washing machine tubs. Use every 30 washes to maintain freshness. Verify fit with your model.