Parts for Ge ABS300K2BB: 01 - Control Panel & Cooktop Parts

Replace a worn, cracked, or missing surface burner control knob on your electric range. Restores smooth heat selection and a clean appearance.

Burner not heating or stuck on? This surface element switch controls power to your cooktop burners. Common repair when heat won't adjust properly.

Burner won't shut off or stays on high? The infinite control switch regulates surface burner heat. Easy DIY repair, typically 10-15 minutes to replace.

Indicator light that illuminates when burners or oven are active. Replace if it stays on constantly or fails to light. Verify fit with your model number.

Oven won't heat or cycles incorrectly? This thermostat senses cavity temperature and regulates heat for consistent cooking. Moderate DIY repair.

Black right-side endcap for electric ranges. Covers exposed panel edges for a finished look. Replace if cracked, broken, loose, or missing.

Right-hand end plate for electric ranges. Replaces cracked, bent, or corroded exterior panel. Restores proper support and alignment to side components.

Left side end plate for electric ranges. Replaces cracked, broken, or missing end panels that provide structural support and finished appearance.

Range clock or timer not working? This control board restores display and cooking time functions. DIY-friendly with video guide. Fits electric and gas ranges.

Secures components to your appliance chassis for a rattle-free fit. Replace missing, stripped, or corroded screws to keep panels and brackets aligned.

Black right-side end cap that finishes and secures trim, rail, or channel ends on your range. Replace if cracked, broken, or missing to restore fit.

This pin locator secures a hinge or shaft pin in place to keep linked appliance components aligned and operating smoothly. It's a small replacement part that restores proper positioning where a locating clip or retainer is used. What it does

• Holds a hinge, shaft, or pivot pin in place to prevent lateral movement
• Restores proper alignment of doors, panels, or linked components
• Helps stop rattling, misalignment, or binding caused by a worn or missing locator
• Works as a direct replacement for the same OEM-labeled locating clip/retainer

• One pin locator

• High-level replacement; basic hand tools usually required
• Disconnect power (and water, if applicable) before servicing appliances with electrical components
• Keep track of small parts and orientation for correct reassembly

Pivot pin that connects the oven door hinge to its mounting bracket. Replace if worn, broken, or missing to restore smooth door operation and alignment.

Factory screw secures brackets, panels, trim, or burner components on ranges, cooktops, and wall ovens. Replaces missing, stripped, or corroded fasteners.

Covers the control panel lamp opening to diffuse light and protect from debris. Replace if broken, cracked, or missing to restore clear indicator visibility.

Black mounting screw secures end caps on electric ranges. Replace missing, stripped, or damaged screws to properly fasten decorative end panels.

Burner not heating or burned out? This 6-inch surface element restores cooking function. Easy plug-in installation takes minutes to complete.

Support rod that props up the lift-up top on your range. Holds the top panel securely in the raised position for cleaning or servicing. Replace if bent or missing.

Replacement 6-inch burner bowl for electric ranges and cooktops. Houses the burner element. Replace if cracked, chipped, rusted, or discolored beyond cleaning.

Fix a burner that won't heat with this range surface burner element. Simple plug-in installation takes minutes. Compatible with multiple models.

Porcelain drip bowl that sits beneath the 8-inch heating element to catch spills and drips. Replace if cracked, rusted, or discolored for easier cleanup.

Secures wiring harness to prevent rubbing and loose connections. Replace if worn or broken to restore proper wire routing. Confirm fit with your model.

Houses and protects cooktop wiring connections. Replace when the original box is damaged, corroded, or missing fasteners for safe electrical connections.

Burner won't seat properly or wobbles? This receptacle clip secures the surface element connection for stable, reliable heat. Simple DIY fix.

Burner not heating or terminal block burned? This electric range terminal block kit restores power to surface elements. Easy 10-15 minute DIY repair.