Parts for Ge PGB935SET2SS: 02 - Control Panel & Cooktop Parts

This right-side end support secures and centers the appliance's rotating assembly so the motor and blower run smoothly. It restores proper alignment and reduces rubbing or wobble that can cause noise or airflow issues. What it does:

• Holds the motor shaft or fan spindle in place to maintain correct rotation alignment
• Keeps the blower/fan wheel properly seated to prevent contact with housing
• Helps reduce vibration and audible noise from a loose or worn support
• Supports reliable airflow by preserving correct component spacing

• One right-side end support

• Disconnect power before starting any repair
• Access may require removing panels or components; keep fasteners organized
• Inspect mating surfaces and brush away debris before installing to ensure a secure fit

This end support is a small mounting bracket that secures the freezer/refrigerator end panel and helps keep the cabinet aligned for smooth door operation and proper seal. It replaces a worn or broken support to restore stability and reduce rattling. What it does:

• Supports and anchors the end panel at the left-front corner of the cabinet
• Maintains correct panel alignment to help doors and seals close properly
• Reduces vibration, shifting, or rattling caused by a damaged or missing support
• Fits into mating slots/tabs on the cabinet frame as the OEM bracket does

• One end support (left-front)

• Basic hand tools required; remove power to appliance before service
• Handle parts carefully to avoid scratching painted surfaces
• Inspect adjacent clips, screws and panels and replace any damaged fasteners

This control trim is the replacement decorative bezel that fits around the appliance control area to restore a finished appearance and cover mounting hardware. It helps keep the control area looking clean and undamaged. What it does

• Replaces cracked, dented or missing control bezel trim to restore the appliance's exterior finish
• Covers control hardware and gaps to improve appearance and reduce dirt buildup
• Provides a snug fit around the control assembly so adjacent panels line up correctly
• Compatible with the original control mounting locations to maintain proper panel alignment

• One control trim piece as shown

• Disconnect power to the appliance before performing any service
• Remove nearby knobs and fasteners as needed; trim typically snaps or screws into place
• Handle trim carefully to avoid scratching the finish during installation

Lower back cover panel for gas ranges. Protects internal components at the rear base. Replace if cracked, damaged, or missing to restore appearance.

Secures components to your appliance chassis for a rattle-free fit. Replace missing, stripped, or corroded screws to keep panels and brackets aligned.

If burners won't ignite automatically but light with a match, the spark module likely failed. Accessed from the back of the range, moderate difficulty.

Cast iron grate for gas range cooktops. Supports cookware over burner. Replace if cracked, chipped, warped, or enamel coating is damaged or worn.

Cast iron center grate for gas range cooktops. Replaces cracked, chipped, or missing middle grate to restore stable support for pots and pans.

Cast iron grate that supports pots and pans over the burner. Replaces a cracked, broken, or missing cooktop grate to restore a stable cooking surface.

Pin locator for gas ranges. Secures and aligns burner components in proper position. Replace if broken, missing, or worn to restore proper burner assembly.

Single fastening screw for range components. Replaces missing, stripped, or damaged screws that secure panels, brackets, and trim pieces in place.

Factory screw secures brackets, panels, trim, or burner components on ranges, cooktops, and wall ovens. Replaces missing, stripped, or corroded fasteners.

Secures cooktop panels, brackets, and components on your gas range. Replace missing, stripped, or damaged screws to eliminate rattles and restore alignment.

Replace your range's control panel glass and circuit board assembly when the display glass is cracked, broken, or the touchpad interface is damaged or unresponsive.

Medium burner cap for gas cooktops and ranges. Sits atop the burner head to distribute flame evenly. Replace if cracked, chipped, or worn from use.

Burner cap sits atop the burner base on gas ranges and cooktops. Replace if cracked, chipped, discolored, or missing to restore a clean appearance.

Replacement burner cap for gas cooktops and ranges. Sits atop the burner head to distribute flame evenly. Replace if cracked, chipped, or worn.

Central burner cap for gas cooktops. Covers the center of the burner to shape flame and protect the burner head. Replace if cracked, worn, or missing.

Replacement small surface burner for gas ranges and cooktops. Installs on stovetop to provide heat for smaller pots. Replace if damaged, discolored, or missing.

Burner base holds and secures the gas burner assembly on your cooktop. Replace if cracked, warped, or corroded to restore proper burner seating.

The Tri-Ring Burner Assembly is an OEM part for GE gas cooktops and ranges. It contains the three front right burners, grates, and supporting brackets.

Causes of a bad burner assembly can include cracked or warped burner heads from prolonged heat exposure. Deterioration of internal gas pipes and orifices may also diminish flame and heating performance.

Symptoms of a bad Tri-Ring Assembly include:

• Unstable, yellowish, or excessively large flames that cannot be adjusted
• Burners that cannot be ignited or controlled independently
• Improper alignment causing imbalanced pans or spills
• Leakage or gas smells detected around the burner cavities

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore branded appliances.

Oval burner assembly for gas range cooktops. Replace if your burner head or cap is cracked, clogged, damaged, or missing. Includes both burner and cap.

The Medium Surface Burner is an OEM part for GE ranges and cooktops. This burner is essential for a wide range of cooking tasks, from simmering sauces to sautéing vegetables. The medium surface burner ensures even heat distribution and efficient fuel consumption, contributing to the overall cooking performance of your appliance.

Causes of a bad Medium Surface Burner can range from clogged burner ports, which impede gas flow and affect flame consistency, to wear and tear on the igniter or the burner assembly that prevents proper operation.

Symptoms of a malfunctioning Medium Surface Burner include:

• Inconsistent flame size or failure to ignite
• Uneven heating or hot spots on the cookware
• Visible damage or corrosion on the burner itself

This OEM GE part is also compatible with Hotpoint, RCA, and some Kenmore models.

Outer burner cap for sealed gas cooktop burners. Shapes flame distribution around the outer ring. Replace if cracked, warped, or missing.

Package of 12

Replacement mounting screw secures panels, brackets, and trim on ranges and cooktops. Install to replace missing, stripped, or rusted fasteners.

Reversible cast iron griddle for gas ranges with flat cooking surface on one side and ridged grill on the other. Replace worn, damaged, or missing griddle.

Hex washer head screw for electric ranges. Secures panels, brackets, and internal components. Replace if screw is stripped, missing, or damaged.